Wireless Laser Scanner Manual Long distance wireless communication Fast decoding speed with a large battery capacity Built-in FLASH memory, supports breakpoint resume Store 2000 pieces Code-128 codes under store mode Supports Windows XP, Win7/8/10, Wince etc. Package included: * Scanner x 1 * USB Cable x 1 * Receiver x 1 * Manual x 1 Ver2.
Barcode Scanner Overview Our wireless scanner integrates a high-performance processor with an effective decoding board, combining a fast decoding speed, high precision and a high anti-interference ability in one device .The device can easily read barcodes on paper with lightning fast scanning speed, a powerful reading ability and high accuracy. Operation Instruction: 1. Choose Communication Mode Working via USB Cable Connect scanner with your device via USB cable.
. LED and Beeper Indication Successful Scan Buzzer LED Yes One beep Light On then OFF Three beeps Light flash once then OFF Continuous beeps Light OFF Failed Important Note: When scanner make continuous beeps please configure the channel for it. Refer to 'Configure Working Channel'. Barcode Programming Our barcode scanners are factory programmed for common terminal and communications settings.
Keyboard Language In order to let scanner output the codes in a correct way, you have to configure the keyboard language before you use it. For example If you use French Keyboard, scan barcode of "French Keyboard", after that scanner will output barcodes according to French keyboard layout. US Keyboard is set by default, if you use a US keyboard you can just skip this part.
Scanning Mode Trigger Mode (Default) Scanning this bar code will enable the scanner to enter manual trigger mode. Trigger Mode Continuous Mode This mode enables the engine to scan/capture, decode and transmit over and over again. Terminator The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF and enabling it by scanning the appropriate barcode below.
Working Mode If you are heading for a working area which lies outside the signal range, you may activate store mode of the scanner. Under store mode, all scanned data will be stored directly into the buffer memory of the device. Furthermore, the data entries will be permanently saved in the buffer memory prior to the manual upload into the working station, so that you may upload them time and again to your liking. 1). By scanning the following barcode, the store mode will be activated Store Mode 2).
5). By scanning the following barcode, the device leaves the store mode, data will be outputed immediately the moment when you scan a barcode. (By default) Quick Store Mode Configure Idle time Important Note-only apply for scanner working via 2.4Ghz channel Scanner will stay awake during the idle time that you set for it and turn to sleep if you haven't used it during the whole idle time.
Configuration Working Channel If there are several scanners working in the same environment, you have to configure the working channel for each scanner, otherwise the data will get crossed when they are working in the same time. Configure Channel 1. Scan one of below channel 2. Scan will make beep beep beep beep ... sound 3.Plug the USB receiver, the beep sound will stop immediately.
Factory Restore Configure the scanner to revert all settings to factory defaults when unkown issues have happened . Factory Restore Start Wireless Scan If there's beep sound, but can not ouput any data please scan below command barcode to start wireless scan. Start Wireless Scan Check scanner Version Scanner below command bercode to check the scanner's version.
Configure Code ID A code ID character identifies the code type of a scanned bar code. This can be useful when decoding more than one code type. The code ID character is inserted between the prefix character (if selected) and the decoded symbol.
Symbologies Users usually need to know barcode type in the process of scanning Code 11 Enable Code 11 Disable Code11 Enable Code11 Multi-Verification Disable Code11 Multi-Verification Code 39 Enable Code39 Disable Code39 Enable transmit Code39 check digit Disable transmit Code39 check digit - 10 -
Enable FULL ASCII Disable FULL ASCII Transmit Code 39 Start/Stop Character Do not Transmit Code 39 Start/Stop Character Enable Code39 Multi-Verification Disable Code39 Multi-Verification Code 32 Enable Code32 Disable Code32 Code 93 Enable Code93 Disable Code93 - 11 -
Enable Code93 Multi-Verification Disable Code93 Multi-Verification Code 128 Enable Code128 Disable Code128 Enable Code128 Multi-Verification Disable Code128 Multi-Verification Codabar Enable Codabar Disable Codabar - 12 -
Transmit Codabar Start/Stop Character Do not Transmit Codabar Start/Stop Character Enable Codabar Multi-Verification Disable Codabar Multi-Verification Interleaved 2 of 5 Enable Interleaved 2 of 5 Disable Interleaved 2 of 5 Enable Interleaved 2 of 5 Multi- verification Disable Interleaved 2 of 5 Multi- verification Industrial 2 of 5 Enable Industrial 2 of 5 Disable Industrial 2 of 5 - 13 -
Enable Industrial 2 of 5 Multi- verification Disable Industrial 2 of 5 Multi-verification China Post Enable China Post Disable China Post MSI Enable MSI Disable MSI Enable MSI Multi-Verification Disable MSI Multi-Verification EAN-8 Enable EAN-8 Disable EAN-8 - 14 -
Transmit EAN-8 check digit Do not transmit EAN-8 check digit EAN-13 Enable EAN-13 Transmit EAN-13 Check Character Disable EAN-13 Do not Transmit EAN-13 Check Character Enable Convert EAN-13 to ISBN Disable Convert EAN-13 to ISBN Enable Convert EAN-13 to ISSN Disable Convert EAN-13 to ISSN - 15 -
UPC-A Enable UPC-A Transmit UPC-A check digit Enable Convert UPC-A to EAN-13 Disable UPC-A Do not transmit UPC-A check digit Disable Convert UPC-A to EAN-13 UPC-E Enable UPC-E Disable UPC-E Transmit UPC-E check digit Do not transmit UPC-E check digit - 16 -
Enable Convert UPC-E to UPC-A Disable Convert UPC-E to UPC-A UPC/EAN Add-on Digits *Disable UPC/EAN Add-on Digits Enable UPC/EAN 2-Digit Add-on Code Enable 5-Digit Add-On Code Enable UPC/EAN 2 or 5 Digit Add-on Code Enable UPC/EAN Multi- verification Disable UPC/EAN Multi-verification - 17 -
Configure Prefix or Suffix Add Prefix 1. Scan code 'add prefix'. This step will clear all previous prefix configuration. Maximum you can add 32 codes. Add Prefix 2. Scan related prefix codes to configure the prefix. For example : ① If you want to add 'MG' as prefixes, first scan code of M then scan Code of G. M G ②Scan 'Test' , there're prefixes of MG before Test. That's MGTEST.
Add Suffix 1. Scan code 'add suffix'. This step will clear all previous suffix configuration. Maximum you can add 32 codes. Add Suffix 2.Scan related suffix codes to configure the suffix. For example : ①If you want to add 'MG' as suffixes, first scan code of M then scan Code of G. M ② G Scan 'Test' , there're suffixes of MG after Test. That's TESTMG.
Hide Front/Back Codes Hide Front Codes Scan barcode of ' Hide Front Codes'. All previous configuration will be cleared. Scan the number that you want to hide. Maximum can hide 32 codes. For example If you want to hide front 2 codes, scan code of $02 Scan test code '123456789' then you will get the result 3456789 Hide Back Codes Scan barcode of ' Hide Back Codes'. All previous configuration will be cleared. Scan the number that you want to hide. Maximum can hide 32 codes.
Hide Number xth Code from the front Scan barcode of ' 0C005'. All previous configuration will be cleared. Scan the number code of the position that you want to hide. For example If you want to hide the second code from the front, scan code of $02 Scan test code '987654321' then you will get the result 97654321.
Appendix A No.
Appendix B： - 23 -
- 24 -
- 25 -
- 26 -
- 27 -
- 28 -
- 29 -
FAQ 1. Some barcodes can not be read, why ? a. Dirty or unclear barcodes might not be read. b. Digital barcode displayed on phone, computers or tablets can’t be read by laser scanner. c. The possible reason is that the configuration for some barcode types are not commonly used is off by default. You need to activate a specific barcode type to get it to work. Please contact the supplier that you’ve purchased it from. 2. The data can not be sent to my computer. Why? a.
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
