NT033 Package Included: 1 x Scanner; 1 x USB Cable; 1 x USB Dongle; 1 x Retractable Clip; 1 x Clip; 1 x Quick Setup Guide; For a complete user guide: https://www.netum.
Product Description Scan Button Battery Light/Read Indicator Light (Green/Blue/Red) Scanning Window Power On Button/ Scan button Scan button Lanyard Eyelet USB Type C (2)
Back Clip peel off the �ilm from back of the clip and stick it to the back of your remote device (3)
Charge the scanner Connect Scanner with your host through USB cable (provided by Netum) or take a DC plug and charge it on an electrical wall outlet. · Red Light - Charging · Green Light - Fully charged · Improtant Notes: DC Plug：V: 5V; A>500mA Warning Tone： Low battery warning - 2 beeps, LED in red �lashing twice Running out of battery - 5 beeps, LED in red �lashing 5 times Scanning will not read any barcodes when it’s running out of battery.
Factory Defaults Scanning the following barcode will restore the scanner to the factory. Scanner will power off after you scanning Factory Restore. %#IFSN0$B Barcode Programming Factory Restore Netum barcode scanners are factory programmed for the most common terminal and communication settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.
USB Wireless Connection 1) Plug USB dongle into your computer. 2) Setup keyboard language. For example if you use French keyboard, just scan “French keyboard” from keyboard language setcion in page 9. 3) Locate cursor on the place where you want scanner to output the characters then you can start to scan. %#IFSN0$1 *Wireless Transmit Bluetooth Connection 1) By scanning “Bluetooth Transmit”, scanner powers off immediately. Press power on button. Blue LED will start to �lash.
Basic Mode (HID) * • NO software installation needed • Connects to most devices • Scanner interacts with host device like a keyboard AT+MODE=2 Applicatin Mode (Apple Speci�ic Serial Pro�ile) • For iOS Devices • If you have an iOS application that supports our Scanners this is the mode to use. AT+MODE=3 Application Mode (Serial Port Pro�ile) • For Android or Windows • Software installation is required. • If you have an application that supports this is the mode recommended.
Transmission Speed Via Bluetooth Connection By scanning the appropriate barcode will change bluetooth transmit speed. AT+HIDDLY=10 *Medium Speed AT+HIDDLY=4 High Speed AT+HIDDLY=25 Low Speed POP OUT IOS Keyboard IOS Keyboard will be disabled when pairing scanner to IOS device. By pressing scanning button in the middle for 4 seconds then release it, will pop out the IOS keyboard.
Scan Mode: Continue Scan Mode This mode enables the scanner to scan/capture, decode and transmit over and over again. By clicking scan button in the middle will turn off/on the continuous scan Mode. continuous Scan Mode Trigger Mode Scanning this bar code will enable the scanner to enter manual trigger mode.
Keyboard Language For example If you use French Keyboard, scan command barcode of “French keyboard ”. US keyboard was setup by default.
$LAN#TK Turkey Q keyboard $LAN#TF Turkey F keyboard Working Mode If you are heading for a working area which lies outside the Bluetooth signal range, you may activate scanner’s store mode, following step described below. Under this mode, all scanned data will be stored directly into buffer memory of the device. Furthermore, data entries will be permanently saved in the buffer memory prior to the manual upload into the working station, so that you may upload them when you are near your working device.
Idle Time Time period set for scanner from idle to sleep.
Beep Volume By scanning the appropriate barcode below will change the beep volume. $BUZZ#1 *High Volume $BUZZ# Low Volume $BUZZ#0 Mute Function Key Mapping When Function Key Mapping is enabled, function characters are sent over the keypad.
LED Activity/Prompt Tone /Indication under different Connections Wireless Connecton: LED Activity Beep Pattern Blue LED On and Off Beep Once Blue LED On and Off Beep Once Blue LED Flash three times Beep Once Working Mode Successful Scan Normal Mode Successful Scan Store Mode Data transmit failed 3 Beeps Blue LED ON and then OFF, Green LED Flashing Indication Wake up from sleep Mode Bluetooth Connection: LED Activity Beep Pattern Blue LED Off→On Beep Once Wake up from sleep Mode 3 Beeps
FAQ 1. Some barcodes cannot be read, why ? a. Dirty or unclear barcodes might not be read. b. The possible reason is that setting for some barcode types not commonly used is off by default. You need to activate a speci�ic barcode type to get it to work. Please contact us for help or you may go to our of�icial website ”www.netum.net” to download the manual and then refer to the section of “Symbologies”. 2.
8. How to turn off the scanner ? Press scan button in the middle for 10 secs will turn off the scanner. 9. Why dose the scanner turn off if I haven’t used it for more than 3mins ? Scanner will enter sleep mode if you haven’t used it in 3mins. (Default idle time- 3 mins) Please do not hesitate to contact us if you need any other con�igurations. Contact Information Tel.: +0086 20-3222-8813 Whatsapp: +86 188 2626 1132 Email: service@netum.net Addr.:Room 301, 6th Floor and full 3rd Floor, Building 1, No.
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
