8800 Series 100-240VAC PSU XCM88PS1 Hardware Installation Guide 350 East Plumeria Drive San Jose, CA 95134 USA February 2011 201-13472-02 1.
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide © 2011 NETGEAR, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc. Technical Support Thank you for choosing NETGEAR. To register your product, get the latest product updates, or get support online, visit us at http://support.netgear.com.
Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Power Supply Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pre-Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100-240VAC PSU XCM88PS1 Installation Note This installation note provides important safety information, specifications, and instructions for installing and removing the NETGEAR 8800 Series 100-240VAC PSU XCM88PS1. This power supply unit can be installed only in NETGEAR 8800 Series switches. This note applies only to the 8800 Series 100-240VAC PSU. For detailed information about NETGEAR switches and all of their compatible PSUs, see the product data sheets available online at www.netgear.com.
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide Before installing an 8800 Series 100-240VAC PSU into your network: • Read the latest installation and safety information provided in the hardware installation guide that describes your switch. • See Appendix A of the hardware installation guide that describes your switch for additional information regarding regulatory compliance certifications. You can download hardware installation guides from www.netgear.com.
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide Power Supply Cords The following power supply cords are provided in the package with the PSU: Table 1.
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide Installing an 8800 Series 100-240VAC PSU CAUTION: Make sure that the PSU circuit is not overloaded. Use proper over-current protection, such as a circuit-breaker, to prevent over-current conditions. To install an 8800 Series 100-240VAC PSU: 1. Attach an ESD-preventive wrist strap to your bare wrist and connect the metal end to the ground receptacle, at the top left corner of the switch front panel. 2.
800 Series 100-240VAC PSU XCM88PS1 Installation Guide Figure 2. Installing a 8800 Series 100-240VAC PSU 4. Secure the PSU by pushing down on the locking handle until it clicks into place. 5. If you are replacing a power supply, you do not need to unplug the AC power cord. For a newly installed power supply, connect an appropriate AC power cord as follows: a. If necessary, remove the power cord retaining bracket as described in the hardware installation guide for your switch. b.
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide Removing an 8800 Series 100-240VAC PSU CAUTION: An operating AC PSU may be hot to the touch; use thermal protective gloves when handling the 8800 Series 100-240VAC PSU during removal. To remove a PSU: 1. Attach an ESD-preventive wrist strap to your wrist. If it is not already attached, connect the metal end to the ground receptacle at the top-left corner of the switch front panel. 2.
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide Front Panel LEDs The front panel of the 8800 Series 100-240VAC PSU provides status LEDs. The following table describes the operation of these LEDs. Table 2.
8800 Series 100-240VAC PSU XCM88PS1 Installation Guide More PSUs are needed to support the load if the low-line power range is used to power the switch. The software determines the maximum available power required for the switch and enables the modules accordingly. The following table lists the specifications for the 8800 Series 100-240VAC PSU. Table 3.
