WN1000RP WiFi Booster for Mobile Installation Guide
Contents Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Meet Your WiFi Booster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Front Panel and Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Bottom Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Button Descriptions . . . . . . . . . . . . . .
Getting Started The NETGEAR WiFi Booster for Mobile increases the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall signal quality over long distances. A WiFi booster repeats the signals from an existing WiFi router or access point. WiFi Booster Boosts the range of your existing WiFi and creates a stronger signal in hard-to-reach areas. Existing WiFi Sometimes your router does not provide the WiFi coverage you need.
Meet Your WiFi Booster Before you install your WiFi booster, familiarize yourself with its LEDs and buttons.
LED Descriptions Use the LEDs during installation to find the best location for the WiFi booster or to monitor the WiFi booster performance. Link Rate LED This LED indicates a wireless connection between the WiFi booster and the router. • Solid green. Best connection. • Solid amber. Good connection. • Solid red. Poor connection. • Off. No connection Status LED This LED is lit when the WiFi booster is powered on.
Button Descriptions The side panel has the following features: • • On/Off button. Turns the device on and off. WPS button. Press the WPS button to wirelessly connect the WiFi booster to your router. All LEDs blink when the WPS connection starts. The bottom panel has the Factory Reset button.To use this button, insert a paper clip into the reset hole and hold it until the Status LED blinks. Then wait for the booster to reboot.
Install the WiFi Booster Place the WiFi booster, apply power, and connect it to your WiFi network. Place the WiFi Booster 1. Place your WiFi booster in the same room as your WiFi router. Note: Proximity to the WiFi router is required only during the initial setup process. 2. Plug the WiFi booster into an electrical outlet and wait one minute. The Status LED lights green. If the Status LED does not light, press the On/Off button.
Connect with WPS Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network name and password. The WPS button is a physical button on the router or access point. WPS does not support WEP network security. If you are using WEP security, see Connect with NETGEAR genie Smart Setup on page 10. To connect with WPS: 1. Press the WPS button on the WiFi booster. 2. Within two minutes, press the WPS button on your WiFi router, gateway, or access point.
3. Find the new WiFi booster network name. The WiFi booster’s network name (SSID) changes to your existing WiFi network name, with _EXT at the end of the name. For example: • Existing WiFi network name. MyNetworkName • New extended network name. MyNetworkName_EXT 4. Connect your existing WiFi devices to the new extended network (MyNetworkName_EXT). Use the same WiFi password that you use for your WiFi router. 5.
Connect with NETGEAR genie Smart Setup 1. Use a WiFi network utility on a computer or mobile device to find and connect to the NETGEAR_EXT (SSID) WiFi network. After the connection with the computer or mobile device is established, the WiFi Device to Booster LED turns green.
2. Open a web browser window from the same computer or mobile device. The browser takes you directly to the NETGEAR genie® Smart Setup. Note: If you are not automatically directed to NETGEAR genie, launch an Internet browser and type www.mywifiext.net in the address field of the browser. Enter admin for the user name and password for the password. 3. Select an existing WiFi network to extend and click the Continue button.
4. Type the network passphrase (also called password or security key) in the PassPhrase field and click the Continue button. 5. Type the name (SSID) for your WiFi booster network in the 2.4GHz Network Name (SSID) field and click the Continue button. Note: You can use the same security settings as your existing network by selecting the check box.
The WiFi booster settings are applied and the following screen displays: 6. Use a WiFi network manager on the computer or mobile device to connect to the WiFi booster’s newly created WiFi network. Repeat this step for all of your computers and mobile devices.
7. Select the check box and click the Continue button.
8. Unplug the WiFi booster and move it to a new location closer to the area with a poor WiFi signal. The location you choose must be within the range of your existing WiFi router network. DO DON’T 9. Plug the WiFi booster into an electrical outlet and wait one minute. The Status LED lights green. If the Status LED does not light, press the On/Off button. Use the Link Rate LED on the front panel to help you choose a spot where the WiFi booster-to-router connection is optimal.
Access WiFi Booster Settings After installation, you can log in to the WiFi booster to view or change the WiFi booster’s settings. To log in to the WiFi booster after the initial set up: 1. Connect a computer or mobile device to the WiFi booster’s network. 2. Launch an Internet browser. 3. Type www.mywifiext.net or www.mywifiext.com in the address field of the browser. A login screen displays. 4. Enter admin for the user name and password for the password.
Frequently Asked Questions You can find more information about your product in the user manual, which is available at http://support.netgear.com. The web browser setup guide keeps asking me for my network security key (passphrase), and I am sure I have entered the correct passphrase. What can I do? The WiFi booster is probably placed at the borderline of the range covered by the router. For more information, see Place the WiFi Booster on page 7.
What are the user name and password to log in to the WiFi booster? The user name is admin and the default password is password. Both are case-sensitive. I have enabled a wireless MAC filter (wireless access control ACL) on my router. What should I do when installing the WiFi booster? When the wireless device connects through the WiFi booster to your router, the MAC address of the wireless device shown on the router is translated to another MAC address.
3. Make sure that the Link Rate LED remains lit. 4. Log in to your router and check the attached devices on the Attached Devices screen. 5. Add any MAC addresses that begin with 02:0F:B5 to your router’s MAC filter table.
Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. NETGEAR recommends that you use only the official NETGEAR support resources.
