User Manual
Table Of Contents
- Contents
- 1. Access the AirBridge and Use the Easy Setup Method
- Related documentation
- Overview
- About NETGEAR Insight
- AirBridge label
- Operation mode: AirBridge Master, AirBridge Satellite, Access Point, or Client Bridge
- AirBridge mode
- Access the AirBridge for initial configuration
- Connect over WiFi using the NETGEAR Insight app on an iOS or Android mobile device
- Connect over the Internet using the NETGEAR Insight Cloud portal
- Connect over WiFi using a WiFi-enabled computer or mobile device
- Connect over Ethernet using a computer connected to the same network
- Connect over Ethernet using a directly connected computer
- Operation mode and default settings after the Day Zero Easy Setup configuration
- Log in to the AirBridge after initial setup
- Change the language of the local browser UI
- 2. Manually Configure or Change the Operation Mode
- 3. Manage the Wired Network Settings
- 4. Manage the WiFi and Radio Features
- Recommended configuration order
- Change the device name of the AirBridge
- Change the country and region of operation
- Change the AirBridge mode
- Scan for neighboring access points
- Specify the approximate distance for the WiFi connection
- Manage the 5 GHz SSIDs and WiFi security
- Change the 5 GHz SSID or WiFi security mode for a satellite
- Change or configure a new 5 GHz SSID for a master with the AirBridge mode enabled
- Change or configure a new 5 GHz SSID for a master with the AirBridge mode disabled
- Change the 5 GHz SSID or WiFi security mode for a client bridge
- Change or configure a 5 GHz SSID for an access point
- Configure a guest network on an access point
- Set up WPA2-Enterprise security on a master or access point
- Set up WPA2-Enterprise security on a satellite or client bridge
- Manage the settings for the 2.4 GHz management SSID
- 5. Manage Advanced WiFi and Radio Features
- Recommended configuration order
- Manage the channel high throughput mode
- Manage the channel or channels
- Manage the radio transmit power
- Change the bit rate
- Manage client limits
- Manage time slot assignments to satellites
- Manage the satellite priority
- Set up a WiFi on/off schedule for a 5 GHz SSID
- Set up a MAC filter for a 5 GHz SSID
- Set up a RADIUS accounting server on a master or access point
- Manually block a WiFi client or connection from a 5 GHz SSID
- Configure traffic shaping for a 5 GHz SSID
- Change the DHCP server settings for a guest WiFi network
- 6. Maintain the AirBridge
- Change the management mode to NETGEAR Insight Mode or Standalone Mode
- Upgrade the firmware on the AirBridge
- Reboot the AirBridge from the local browser UI
- Schedule the AirBridge to reboot
- Manage the configuration file of the AirBridge
- Reset the AirBridge to factory default settings
- Manage the date and time settings
- Configure and view the logs
- Set up email alerts
- Manage access security settings
- Specify a management VLAN
- 7. Monitor the AirBridge and its Network Connections
- 8. Perform Diagnostics and Troubleshooting
- Send a ping
- Send a traceroute request
- Send a name server lookup request
- Perform a speed test
- Quick tips for troubleshooting
- Troubleshoot with the LEDs
- Troubleshoot the WiFi connectivity
- You cannot log in to the AirBridge over a LAN connection
- Changes are not saved
- Troubleshoot your network using your computer ping utility
- A. Factory Default Settings and Technical Specifications
7.
Enter the settings that are described in the following table.
DescriptionSetting
From the menu, select the country and region in which the AirBridge is operating.
Note: Make sure that the country is set to the location where the device is operating. You
are responsible for complying with the local, regional, and national regulations that are
set for channels, power levels, and frequency ranges.
Note: It might not be legal to operate the AirBridge in a region other than the regions
listed in the menu. If your country or region is not listed, check with your local government
agency.
Country/Region
From the menu, select the time zone for the country and region in which the AirBridge is
operating.
Time Zone
By default, the DHCP client of the AirBridge allows the AirBridge to receive an IP address
from a DHCP server (or router that functions as a DHCP server) in your network.
To set up the AirBridge with a static (fixed) IP address, do the following:
a. Select the Disable radio button.
Additional fields display.
b. Specify the IP address, IP subnet mask, IP address of the default gateway, and IP address
of the DNS server.
DHCP Client
As an option, enter a new device name for the AirBridge. The name must contain
alphanumeric characters, cannot be longer than 15 characters, and cannot contains spaces.
The name can contain hyphens, but cannot start or end with a hyphen.
By default, the device name is WBC502, which is the AirBridge’s model number.
AP Name
Enter a new local device password. This is the password that you must use to log in to the
AirBridge’s local browser UI. (It is not the password that you use for WiFi access.)
The password must be 8 to 32 characters in length and must contain at least one uppercase
letter, one lowercase letter, and one number. The following special characters are allowed:
! @ # $ % ^ & * ( )
Write down and save the password for future use.
AP Login New
Password
Enter exactly the same password that you entered in the AP Login New Password field.Confirm New
Password
User Manual30Access the AirBridge and Use
the Easy Setup Method
Insight Instant AirBridge WBC502 User Manual