User Manual
Table Of Contents
- Contents
- 1. Access the AirBridge and Use the Easy Setup Method
- Related documentation
- Overview
- About NETGEAR Insight
- AirBridge label
- Operation mode: AirBridge Master, AirBridge Satellite, Access Point, or Client Bridge
- AirBridge mode
- Access the AirBridge for initial configuration
- Connect over WiFi using the NETGEAR Insight app on an iOS or Android mobile device
- Connect over the Internet using the NETGEAR Insight Cloud portal
- Connect over WiFi using a WiFi-enabled computer or mobile device
- Connect over Ethernet using a computer connected to the same network
- Connect over Ethernet using a directly connected computer
- Operation mode and default settings after the Day Zero Easy Setup configuration
- Log in to the AirBridge after initial setup
- Change the language of the local browser UI
- 2. Manually Configure or Change the Operation Mode
- 3. Manage the Wired Network Settings
- 4. Manage the WiFi and Radio Features
- Recommended configuration order
- Change the device name of the AirBridge
- Change the country and region of operation
- Change the AirBridge mode
- Scan for neighboring access points
- Specify the approximate distance for the WiFi connection
- Manage the 5 GHz SSIDs and WiFi security
- Change the 5 GHz SSID or WiFi security mode for a satellite
- Change or configure a new 5 GHz SSID for a master with the AirBridge mode enabled
- Change or configure a new 5 GHz SSID for a master with the AirBridge mode disabled
- Change the 5 GHz SSID or WiFi security mode for a client bridge
- Change or configure a 5 GHz SSID for an access point
- Configure a guest network on an access point
- Set up WPA2-Enterprise security on a master or access point
- Set up WPA2-Enterprise security on a satellite or client bridge
- Manage the settings for the 2.4 GHz management SSID
- 5. Manage Advanced WiFi and Radio Features
- Recommended configuration order
- Manage the channel high throughput mode
- Manage the channel or channels
- Manage the radio transmit power
- Change the bit rate
- Manage client limits
- Manage time slot assignments to satellites
- Manage the satellite priority
- Set up a WiFi on/off schedule for a 5 GHz SSID
- Set up a MAC filter for a 5 GHz SSID
- Set up a RADIUS accounting server on a master or access point
- Manually block a WiFi client or connection from a 5 GHz SSID
- Configure traffic shaping for a 5 GHz SSID
- Change the DHCP server settings for a guest WiFi network
- 6. Maintain the AirBridge
- Change the management mode to NETGEAR Insight Mode or Standalone Mode
- Upgrade the firmware on the AirBridge
- Reboot the AirBridge from the local browser UI
- Schedule the AirBridge to reboot
- Manage the configuration file of the AirBridge
- Reset the AirBridge to factory default settings
- Manage the date and time settings
- Configure and view the logs
- Set up email alerts
- Manage access security settings
- Specify a management VLAN
- 7. Monitor the AirBridge and its Network Connections
- 8. Perform Diagnostics and Troubleshooting
- Send a ping
- Send a traceroute request
- Send a name server lookup request
- Perform a speed test
- Quick tips for troubleshooting
- Troubleshoot with the LEDs
- Troubleshoot the WiFi connectivity
- You cannot log in to the AirBridge over a LAN connection
- Changes are not saved
- Troubleshoot your network using your computer ping utility
- A. Factory Default Settings and Technical Specifications
Perform a speed test
You can perform a speed test between the AirBridge and an IPv4 address or host name
and view the results of the speed test. You can also use this option to determine the
general network performance. The maximum speed that the AirBridge can measure is
100 Mbps.
Use the speed test to determine the point-to-point link speed between a master and a
satellite or between an access point and a client bridge. For example, after the
point-to-point link between a master and a satellite is established, you can do the
following:
•
On the master, enter the IP address of the satellite, and perform the speed test to
determine the speed of the downlink, which is the link from the master to the satellite.
•
On the satellite, enter the IP address of the master, and perform the speed test to
determine the speed of the uplink, which is the link from the satellite to the master.
To perform a speed test:
1.
Open a web browser from a computer that is connected to the same network as the
AirBridge or directly to the AirBridge through an Ethernet cable or WiFi connection.
2. Enter the IP address that is assigned to the AirBridge.
The login page displays.
If your browser does not display the login page but displays a security message and
does not let you proceed, see Log in to the AirBridge after initial setup on page 34.
3. Enter the AirBridge user name and local device password.
The user name is admin. The local device password is the one that you specified
the first time that you logged in. The user name and password are case-sensitive.
If you previously managed the AirBridge through the NETGEAR Insight app or Insight
Cloud portal, enter the Insight network password for the Insight network location to
which the AirBridge was assigned (see Connect over WiFi using the NETGEAR Insight
app on an iOS or Android mobile device on page 15).
The Device Status page displays the Device Information section and other sections.
4. Under Management, select Tools.
By default, the Ping tab is selected and the Ping Test Parameters page displays.
5. Select the Speed Test tab.
The Speed Test Parameters page displays.
6.
In the Target IP / Domain Name field, enter the IP address or domain name for
which you want to perform a speed test.
User Manual145Perform Diagnostics and
Troubleshooting
Insight Instant AirBridge WBC502 User Manual