User's Manual
Table Of Contents
- Contents
- 1. Overview
- Supported Orbi Pro WiFi 6 models
- Orbi Pro WiFi 6 router and satellite hardware overviews
- LED behavior
- Wall mount your Orbi Pro WiFi 6
- Orbi Pro WiFi 6 router label and Orbi Pro Wifi 6 satellite label
- Connect your Orbi Pro WiFi 6 router
- Place your Orbi Pro WiFi 6 satellite
- Sync your Orbi Pro WiFi 6 satellite
- Set up your Orbi network with the NETGEAR Insight app
- 2. Connect to the Orbi Pro WiFi 6 Network and Access the Router
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Manage an IPv6 Internet connection
- Requirements for entering IPv6 addresses
- Specify IPv6 Internet connections
- Use auto detection for an IPv6 Internet connection
- Use auto configuration for an IPv6 Internet connection
- Set up an IPv6 6rd tunnel Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up an IPv6 fixed Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Change the MTU size
- 4. Control Access to the Internet
- Manage MAC access control lists for WiFi networks and the LAN
- Manage the Orbi network access control list
- Use keywords to block Internet sites
- Delete keywords that are used to block Internet sites
- Avoid blocking on a trusted computer
- Block services from the Internet
- Schedule when to block Internet sites and services
- Set up security event email notifications
- 5. Specify Network Settings
- View or change WAN settings
- Change the WAN port speed
- Manage Dynamic DNS
- Set up a default DMZ server
- Change the router’s device name
- Manage the LANs
- Use the router as a DHCP server
- Disable a DHCP server feature in the router
- Manage reserved LAN IP addresses
- Manage custom static routes
- Change the admin WiFi network settings
- Manage the employee WiFi network settings
- Manage the IoT WiFi network settings
- Set up a guest WiFi network and captive portal
- Manage the download bandwidth per SSID
- View or change advanced WiFi settings
- Use the router as a WiFi access point
- Set up router mode
- Generate a new backhaul password
- Enable or disable MU-MIMO
- Enable or disable fast roaming
- Enable or disable Protected Management Frames
- Check your Internet bandwidth
- Manage the VLANs
- Improve network connections with Universal Plug and Play
- 6. Manage Your Network
- Update the router and satellite firmware
- Change the admin password
- Enable admin password reset
- Reset the admin password
- View router status and usage information
- Display Internet port statistics
- Check the Internet connection status
- View satellites, WiFi devices, and wired devices connected to the Orbi network
- View satellite status
- View and manage logs of router activity
- Set up a syslog server
- Monitor Internet traffic
- Set Your Time Zone
- Change the NTP Server
- Manage the router configuration file
- Set up remote management
- Use remote access
- 7. Customize Internet Traffic Rules for Ports
- 8. Use VPN to Access Your Network
- 9. Troubleshooting
- A. Supplemental Information
You can now add and manage devices on the MAC ACL. For more information, see the
following sections:
•
Add automatically detected devices to a MAC ACL on page 49
•
Manually add, remove, or change the information for a device on a MAC ACL on
page 50
Add automatically detected devices to a MAC ACL
After you set up a MAC ACL for a network and specify the default policy for the MAC
ACL, the router automatically detects devices that are connected or were connected to
the network for which you set up the MAC ACL.
You can select one or multiple devices from the detected list and add them to the MAC
ACL.
To add automatically detected devices to a MAC ACL:
1.
Launch a web browser from a computer or mobile device that is connected to the
access point/router network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the router admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select ADVANCED > Security > MAC ACL.
The MAC ACL page displays.
5.
Go to the section for the network for which you want to manage the MAC ACL.
The first section is for the admin WiFi network, the second for the employee WiFi
network, the third for the IoT WiFi network, the fourth for the guest WiFi network,
and the fifth for the wired network.
6. Click the ADD DEVICE button.
The Manual Access Management pop-up window opens.
7.
Select the check boxes for the devices that you want to add to the MAC ACL.
8. Click the ADD button.
User Manual49Control Access to the Internet
Orbi Pro WiFi 6 Router SXR80 and Orbi Pro WiFi 6 Satellite SXR80