User Manual
Table Of Contents
- Contents
- 1. Overview
- 2. Connect to the Network and Access the Router
- 3. Specify Your Internet Settings
- Manually set up the Internet connection
- Manage an IPv6 Internet connection
- Requirements for entering IPv6 addresses
- Specify IPv6 Internet connections
- Use auto detection for an IPv6 Internet connection
- Use auto configuration for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up an IPv6 fixed Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Set up an IPv6 6rd tunnel Internet connection
- Change the MTU size
- 4. Control Access to the Internet
- Manage NETGEAR Armor
- Allow or block access to your network
- Manage network access control lists
- Use keywords to block Internet sites
- Delete keywords that are used to block Internet sites
- Avoid blocking on a trusted computer
- Block services from the Internet
- Schedule when to block Internet sites and services
- Set up security event email notifications
- 5. Specify Network Settings
- About the WiFi networks
- Manage the settings for the main WiFi network
- Manage WiFi settings for the 6 GHz-only WiFi network
- Manage IoT WiFi settings
- Set up a guest WiFi network
- Change your region
- View or change WAN settings
- Manage the WAN preference
- Manage Dynamic DNS
- Set up a default DMZ server
- Change the router’s device name
- Change the LAN TCP/IP settings
- Use the router as a DHCP server
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Manage custom static routes
- Enable or disable 20/40 MHz coexistence for the 2.4 GHz radio
- Enable or disable Wi-Fi Multimedia Quality of Service
- Change the CTS/RTS threshold and preamble mode for a radio
- Change the Transmission Power Control
- Use the router as a WiFi access point only
- Set up router mode
- Generate a new backhaul password
- Improve network connections with Universal Plug and Play
- Set up a bridge for a port group or VLAN tag group
- 6. Manage Your Network
- Update the router and satellite firmware
- Change the admin password
- Enable admin password reset
- Reset the admin password
- Always use HTTPS to access the router
- View router status and usage information
- Display Internet port statistics
- Check the Internet connection status
- View and manage logs of router activity
- View devices connected to the network or edit device information
- View satellites connected to the network or edit satellite information
- View the satellite status
- Check your Internet bandwidth
- Monitor Internet traffic
- Change the NTP server
- Set the time zone
- Manage the router configuration file
- 7. Customize Internet Traffic Rules for Ports
- 8. Use OpenVPN to Access Your Network
- 9. Troubleshooting
- A. Factory Settings and Technical Specifications
Change the 2.4 GHz, 5 GHz, or 6 GHz WiFi channel
You can change the 2.4 GHz, 5 GHz, or 6 GHz WiFi channel.
In some regions, not all channels are available. Do not change the channel unless you
experience interference (shown by lost connections or slow data transfers). If this
happens, experiment with different channels to see which is the best.
When you use multiple access points, it is better if adjacent access points use different
channels to reduce interference. The recommended channel spacing between adjacent
access points is four channels (for example, for the 2.4 GHz radio band, use Channels
1 and 5, or 6 and 10).
Note: If you change the 2.4 GHz or 5 GHz channel, the change also applies to the IoT
network and the guest network. If you change the 6 GHz channel, the change also
applies to the separate 6 GHz-only network.
To change the WiFi channel:
1.
Launch a web browser from a computer or mobile device that is connected to your
Orbi network.
2. Enter orbilogin.com.
A login window opens.
3. Enter the Orbi admin user name and password.
The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.
The BASIC Home page displays.
4. Select Wireless.
The Wireless Settings page displays.
5.
To change the 2.4 GHz, 5 GHz, or 6 GHz WiFi channel, select a number from one of
the following menus:
•
2.4 GHz Channel
•
5 GHz Channel
•
6 GHz Channel
Note: You can change the channel for one, two, or all three radio bands.
6. Click the Apply button.
Your settings are saved. The router sends the new settings to the satellite.
User Manual60Specify Network Settings
Orbi Quad-Band Mesh WiFi 6E System