User Manual
Table Of Contents
- Contents
- 1. Overview
- 2. Connect to the Network and Access the Router
- 3. Specify Your Internet Settings
- Manually set up the Internet connection
- Manage an IPv6 Internet connection
- Requirements for entering IPv6 addresses
- Specify IPv6 Internet connections
- Use auto detection for an IPv6 Internet connection
- Use auto configuration for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up an IPv6 fixed Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Set up an IPv6 6rd tunnel Internet connection
- Change the MTU size
- 4. Control Access to the Internet
- Manage NETGEAR Armor
- Allow or block access to your network
- Manage network access control lists
- Use keywords to block Internet sites
- Delete keywords that are used to block Internet sites
- Avoid blocking on a trusted computer
- Block services from the Internet
- Schedule when to block Internet sites and services
- Set up security event email notifications
- 5. Specify Network Settings
- About the WiFi networks
- Manage the settings for the main WiFi network
- Manage WiFi settings for the 6 GHz-only WiFi network
- Manage IoT WiFi settings
- Set up a guest WiFi network
- Change your region
- View or change WAN settings
- Manage the WAN preference
- Manage Dynamic DNS
- Set up a default DMZ server
- Change the router’s device name
- Change the LAN TCP/IP settings
- Use the router as a DHCP server
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Manage custom static routes
- Enable or disable 20/40 MHz coexistence for the 2.4 GHz radio
- Enable or disable Wi-Fi Multimedia Quality of Service
- Change the CTS/RTS threshold and preamble mode for a radio
- Change the Transmission Power Control
- Use the router as a WiFi access point only
- Set up router mode
- Generate a new backhaul password
- Improve network connections with Universal Plug and Play
- Set up a bridge for a port group or VLAN tag group
- 6. Manage Your Network
- Update the router and satellite firmware
- Change the admin password
- Enable admin password reset
- Reset the admin password
- Always use HTTPS to access the router
- View router status and usage information
- Display Internet port statistics
- Check the Internet connection status
- View and manage logs of router activity
- View devices connected to the network or edit device information
- View satellites connected to the network or edit satellite information
- View the satellite status
- Check your Internet bandwidth
- Monitor Internet traffic
- Change the NTP server
- Set the time zone
- Manage the router configuration file
- 7. Customize Internet Traffic Rules for Ports
- 8. Use OpenVPN to Access Your Network
- 9. Troubleshooting
- A. Factory Settings and Technical Specifications
Connect your router
Note: If both your Internet service provider (ISP) and modem support a speed of
10 Gbps, the router’s Internet connection also functions at 10 Gbps. Otherwise, the
Internet connection functions at the maximum speed that either your ISP or your modem
supports. (1 Gbps is a common speed.)
Power on your router and connect it to a modem.
To connect your router to a modem:
1.
Unplug your modem’s power, leaving the modem connected to the wall jack for
your Internet service.
If your modem uses a battery backup, remove the battery.
2. Plug in and turn on your modem.
If your modem uses a battery backup, put the battery back in.
3.
Connect your modem to the Internet port of your router with the Ethernet cable that
came with your router.
Note: If both your ISP and modem support a speed that is higher than 1 Gbps (for
example, 2.5 Gbps, 5 Gbps, or 10 Gbps), we recommend that you use the Category
(Cat) 6 Ethernet cable that came in the box. A Cat 6 Ethernet cable is better suited
to higher speeds. If your ISP or modem supports a speed of 1 Gbps, you can use a
Cat 5E Ethernet cable.
4.
(Optional) If your package comes with plug adapters for the power adapter, connect
the plug adapter for your region to the power adapter.
User Manual15Overview
Orbi Quad-Band Mesh WiFi 6E System