Data Sheet

NETGEAR M4200 series key features:
•Eight full power PoE+ and multi-speed 1G, 2.5G ports combined with
two 10G SFP+ uplinks
•Allow for a fully non-blocking deployment of eight Wave 2 11ac access
points, with 240W PoE budget
•Two of these multi-speed 1G, 2.5G PoE+ ports also support 5G
•NBASE-T compliant Multigigabit Ethernet (basis for the upcoming
IEEE 802.3bz standard)
•2.5X to 5X faster speeds up to 100m on legacy Cat5e/Cat6 cables -
yet providing 100M and 1G backward compatibility
•Whisper quiet 28.9dB acoustics when operating at 25°C (77°F),
well below normal oces ambient background noise
•Secure placement above drop-down ceilings, in air passageways
and where other switches will not go, vertical or horizontal, flat or
perpendicular
•Easy Mount options whether it’s directly on a wall, attached to a
rectangular or round pole, or mounted in a standard 19-inch rack
•Low latency and scalable table size with 16K MAC, 1K ARP/NDP,
1K VLANs, 32 routes (IPv4) and 32 routes (IPv6)
•SDN-Ready OpenFlow 1.3 support for maximum investment protection
NETGEAR M4200 series soware features:
•Advanced classifier-based, time-based hardware implementation for
L2 (MAC), L3 (IP) and L4 (UDP/TCP transport ports) security and
prioritization
•Selectable Port-Channel / LAG (802.3ad - 802.1AX) L2/L3/L4
hashing for fault tolerance and load sharing with any type of Ethernet
channeling
•Voice VLAN with SIP, H323 and SCCP protocols detection and LLDP-
MED IP phones automatic QoS and VLAN configuration
•Ecient authentication tiering with successive DOT1X, MAB and
Captive Portal methods for streamlined BYOD
•Comprehensive IPv4/IPv6 static and IPv4 dynamic routing including RIP
•Layer 2 multicast forwarding with IGMPv3/MLDv2 Snooping and
IGMPv2/MLDv1 Snooping Querier
•Advanced security including malicious code detection, DHCP Snooping,
Dynamic ARP Inspection and DoS attacks mitigation
•Innovative multi-vendor Auto-iSCSI capabilities
NETGEAR M4200 series resiliency and availability features:
•Link Dependancy new feature enables or disables ports based on the
link state of dierent ports
•Per VLAN Spanning Tree and Per VLAN Rapid Spanning Tree (PVSTP/
PVRSTP) oer interoperability with PVST+ infrastructures
NETGEAR M4200 series management features:
•DHCP/BootP innovative auto-installation including firmware and
configuration file upload automation
•Industry standard SNMP, RMON, MIB, LLDP, AAA, sFlow and RSPAN
remote mirroring implementation
•Service port for out-of-band Ethernet management (OOB)
•Standard RS232 straight-through serial RJ45 and Mini-USB ports for
local management console
•Standard USB port for local storage, logs, configuration or image files
•Dual firmware image and configuration file for updates with minimum
service interruption
•Industry standard command line interface (CLI) for IT admins used to
other vendors commands
•Fully functional Web console (GUI) for IT admins who prefer an easy to
use graphical interface
•Single-pane-of-glass NMS300 management platform with mass-
configuration support
NETGEAR M4200 series warranty and support:
•NETGEAR ProSAFE Lifetime Hardware Warranty*
•Included Lifetime Technical Support
•Included Lifetime Next Business Day Hardware Replacement
Product Brief
The ProSAFE® M4200-10MG-PoE+ Managed Switch was designed from the ground up to optimize the installation of Wave 2 11ac access points.
Includes eight full power PoE+ and multi-speed 1G, 2.5G ports for 100 meter cable runs, combined with two 10G uplinks for a fully non-blocking
deployment of eight Wave 2 11ac access points. NETGEAR Multigigabit Ethernet is compatible with most major wireless and switching vendors
managed solutions, and the only one with 8x2.5G to the AP and 2x10G line-rate aggregation to the wiring closet. Plenum rated, slim design and
mounting accessories allow for access point placement optimization and cabling eciency.
ProSAFE® Intelligent Edge Managed Switches Data Sheet
M4200 series
Page 3 of 31