Brochure

NETGEAR M4200 series key features:
• Eight full power PoE+ and multi-speed 1G, 2.5G ports combined with two 10G SFP+ uplinks
• Allow for a fully non-blocking deployment of eight Wave 2 11ac access points, with 240W PoE
budget
• Two of these multi-speed 1G, 2.5G PoE+ ports also support 5G
• NBASE-T compliant Multigigabit Ethernet (basis for the upcoming
IEEE 802.3bz standard)
• 2.5X to 5X faster speeds up to 100m on legacy Cat5e/Cat6 cables - yet providing 100M and
1G backward compatibility
• Whisper quiet 28.9dB acoustics when operating at 25°C (77°F),
well below normal oces ambient background noise
• Secure placement above drop-down ceilings, in air passageways and where other switches will
not go, vertical or horizontal, flat or perpendicular
• Easy Mount options whether it’s directly on a wall, attached to a rectangular or round pole, or
mounted in a standard 19-inch rack
• Low latency and scalable table size with 16K MAC, 1K ARP/NDP,
1K VLANs, 32 routes (IPv4) and 32 routes (IPv6)
• SDN-Ready OpenFlow 1.3 support for maximum investment protection
NETGEAR M4200 series soware features:
• Advanced classier-based, time-based hardware implementation for L2 (MAC), L3 (IP) and L4
(UDP/TCP transport ports) security and prioritization
• Selectable Port-Channel / LAG (802.3ad - 802.1AX) L2/L3/L4 hashing for fault tolerance and
load sharing with any type of Ethernet channeling
• Voice VLAN with SIP, H323 and SCCP protocols detection and LLDP-MED IP phones automatic
QoS and VLAN conguration
• Ecient authentication tiering with successive DOT1X, MAB and Captive Portal methods for
streamlined BYOD
• Comprehensive IPv4/IPv6 static and IPv4 dynamic routing including RIP
• Layer 2 multicast forwarding with IGMPv3/MLDv2 Snooping and IGMPv2/MLDv1
Snooping Querier
• Advanced security including malicious code detection, DHCP Snooping, Dynamic ARP
Inspection and DoS attacks mitigation
• Innovative multi-vendor Auto-iSCSI capabilities
NETGEAR M4200 series resiliency and availability features:
• Link Dependancy new feature enables or disables ports based on the link state of
dierent ports
• Per VLAN Spanning Tree and Per VLAN Rapid Spanning Tree (PVSTP/PVRSTP) oer
interoperability with PVST+ infrastructures
NETGEAR M4200 series management features:
• DHCP/BootP innovative auto-installation including rmware and conguration le upload
automation
• Industry standard SNMP, RMON, MIB, LLDP, AAA, sFlow and RSPAN remote mirroring
implementation
• Service port for out-of-band Ethernet management (OOB)
• Standard RS232 straight-through serial RJ45 and Mini-USB ports for local management console
• Standard USB port for local storage, logs, conguration or image les
• Dual rmware image and conguration le for updates with minimum service interruption
• Industry standard command line interface (CLI) for IT admins used to other vendors commands
• Fully functional Web console (GUI) for IT admins who prefer an easy to use graphical interface
• Single-pane-of-glass NMS300 management platform with mass-conguration support
NETGEAR M4200 series warranty and support:
• NETGEAR ProSAFE Lifetime Hardware Warranty*
• Included Lifetime Technical Support
• Included Lifetime Next Business Day Hardware Replacement
M4200 Series Features
The ProSAFE® M4200-10MG-PoE+ Managed Switch was designed from the ground up to optimize the installation of Wave 2 11ac access points. Includes eight
full power PoE+ and multi-speed 1G, 2.5G ports for 100 meter cable runs, combined with two 10G uplinks for a fully non-blocking deployment of eight Wave
2 11ac access points. NETGEAR Multigigabit Ethernet is compatible with most major wireless and switching vendors managed solutions, and the only one with
8x2.5G to the AP and 2x10G line-rate aggregation to the wiring closet. Plenum rated, slim design and mounting accessories allow for access point placement
optimization and cabling eciency.