User Manual
Table Of Contents
- S350 Series 8-Port Gigabit Ethernet Smart Switch
- Contents
- 1 Get Started
- Available Publications
- Switch Management and Discovery Overview
- Options to Change the Default IP Address of the Switch
- Discover or Change the Switch IP Address
- About the User Interfaces
- Access the Local Browser Interface
- Change the Language of the Local Browser Interface
- Use the Device View of the Local Browser Interface
- Interface Naming Conventions
- Configure Interface Settings
- Context-Sensitive Help and Access to the Support WebSite
- Access the User Guide Online
- Register Your Product
- 2 Configure System Information
- 3 Configure Switching
- Configure the Port Settings and Maximum Frame Size
- Configure Link Aggregation Groups
- Configure VLANs
- Configure a Voice VLAN
- Configure Auto-VoIP
- Configure Spanning Tree Protocol
- Configure Multicast
- View and Search the MFDB Table
- View the MFDB Statistics
- Configure the Auto-Video Multicast Settings
- About IGMP Snooping
- Configure IGMP Snooping
- Configure IGMP Snooping for Interfaces
- View, Search, or Clear the IGMP Snooping Table
- Configure IGMP Snooping for VLANs
- Modify IGMP Snooping Settings for a VLAN
- Disable IGMP Snooping on a VLAN
- Configure a Multicast Router Interface
- Configure a Multicast Router VLAN
- IGMP Snooping Querier Overview
- Configure an IGMP Snooping Querier
- Configure an IGMP Snooping Querier for VLANs
- Display IGMP Snooping Querier for VLAN Status
- View, Search, and Manage the MAC Address Table
- Configure Layer 2 Loop Protection
- 4 Configure Quality of Service
- 5 Manage Device Security
- Configure the Management Security Settings
- Configure Management Access
- Configure Port Authentication
- Set Up Traffic Control
- Configure Access Control Lists
- Use the ACL Wizard to Create a Simple ACL
- Configure a Basic MAC ACL
- Configure MAC ACL Rules
- Configure MAC Bindings
- View or Delete MAC ACL Bindings in the MAC Binding Table
- Configure a Basic or Extended IP ACL
- Configure Rules for a Basic IP ACL
- Configure Rules for an Extended IP ACL
- Configure IP ACL Interface Bindings
- View or Delete IP ACL Bindings in the IP ACL Binding Table
- Configure VLAN ACL Bindings
- 6 Monitor the System
- 7 Maintenance
- A Configuration Examples
- B Specifications and Default Settings
S350 Series 8-Port Gigabit Ethernet Smart Switch Models GS308T and GS310TP
Manage Device Security User Manual219
5. Select Security > Access > HTTPS > HTTPS Configuration.
6. Select the Admin Mode Enable or Disable radio button.
This selection enables or disables secure HTTP (HTTPS). The default value is Enable.
You can download SSL certificates only when HTTPS is disabled.
You can enable
HTTPS only if a certificate is present on the device.
7. In the HTTPS Port field, type the HTTPS port number.
The range is from 1025 to 65535.
The default is port 443.
8. In the HTTPS Session Soft Timeout (Minutes)
field, enter the inactivity time-out for
HTTPS sessions.
The range is from 1 to 60 minutes. The default value is 5 minutes.
9. In the HTTPS Session Hard Timeout (Hours) field, set the hard time-out for HTTPS
sessions.
This time-out is unaf
fected by the activity level of the session. The range is from 1 to 168
hours. The default is 24 hours.
10. In the Maximum Number of HTTPS Sessions field, enter the maximum allowable number
of HTTPS sessions.
The range is from 1 to 4 sessions.
The default is 4 sessions.
11. Click the Apply button.
Your settings are saved.
Manage Certificates for HTTPS Access
You can manage certificates for HTTPS access.
Generate an SSL Certificate
Note: Before you can generate a certificate, you must disable HTTPS (see
Configure HTTPS Access Settings on page 218) and log back in to
the local browser interface over an HTTP session. After you generate
the certificate, you can reenable HTTPS and log back in to the local
browser interface over an HTTPS session.