User Manual
Table Of Contents
- Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports
- Contents
- 1. Getting Started
- Switch Management Options and Default Management Mode
- Available Publications
- Web Browser Requirements and Supported Browsers
- User-Defined Fields
- Interface Naming Conventions
- Access the Switch
- Change the Management Mode of the Switch
- Register the Switch
- How to Configure Interface Settings
- Local Browser Interface Device View
- 2. Configure System Information
- View and Configure the Switch Management Settings
- View or Define System Information
- View the Switch CPU Status
- Configure the CPU Thresholds
- Configure the IPv4 Address for the Network Interface and Management VLAN
- Configure the IPv6 Address for the Network Interface
- View the IPv6 Network Neighbor
- Configure the Time Settings
- Configure Denial of Service Settings
- Configure DNS Settings
- Configure Green Ethernet Settings
- Manage the Bonjour Settings and View Bonjour Information
- Control the LEDs
- Use the Device View
- Configure Power over Ethernet
- Configure Link Layer Discovery Protocol
- Configure DHCP L2 Relay and DHCP Snooping
- Set Up PoE Timer Schedules
- View and Configure the Switch Management Settings
- 3. Configure Switching
- 4. Configuring Routing
- 5. Configure Quality of Service
- 6. Manage Device Security
- Management Security Settings
- Configure Management Access
- Configure Port Authentication
- Set Up Traffic Control
- Configure Access Control Lists
- Use the ACL Wizard to Create a Simple ACL
- Configure a Basic MAC ACL
- Configure MAC ACL Rules
- Configure MAC Bindings
- View or Delete MAC ACL Bindings in the MAC Binding Table
- Configure an IP ACL
- Configure Rules for a Basic IP ACL
- Configure Rules for an Extended IP ACL
- Configure an IPv6 ACL
- Configure Rules for an IPv6 ACL
- Configure IP ACL Interface Bindings
- View or Delete IP ACL Bindings in the IP ACL Binding Table
- Configure VLAN ACL Bindings
- 7. Perform Maintenance Tasks
- 8. Manage Power over Ethernet
- 9. Monitor the System
- A. Configuration Examples
- B. Hardware Specifications and Default Values
Configure System Information
67
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports
5. Select System > Management > Green Ethernet > Green Ethernet Summary.
The Green Ethernet Statistics Summary page displays.
6. To refresh the page, click the Refresh button.
The following table describes the nonconfigurable fields.
Configure the Green Ethernet EEE LPI History
You can configure and view the Green Ethernet low power idle (LPI) history.
To configure the port Green Ethernet EEE LPI history:
1. Connect your computer to the same network as the switch.
You can use a WiFi or wired connection to connect your computer to the network, or
connect directly to a switch that is off-network using an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch on page 13.
The login window opens.
Table 17. Green Ethernet Statistics Summary information
Field Description
Current Power Consumption (mW) Estimated power consumption by all ports of the switch in mWatts.
Percentage Power Saving (%) Estimated percentage of power saved on all ports of the switch if the green
modes are enabled.
Cumulative Energy Saving (W * H) Estimated cumulative energy saved on the switch in watts multiplied by
hours if all green modes are enabled.
Unit The unit ID.
Green Features supported on this
unit
List of green features supported on the given unit, which could be one or
more of the following: Energy-Detect (Energy Detect), Short-Reach (Short
Reach), EEE (Energy Efficient Ethernet), LPI-History (EEE Low Power Idle
History), LLDP-Cap-Exchg (EEE LLDP Capability Exchange), Pwr-Usg-Est
(Power Usage Estimates).
Interface Interface for which data is displayed or configured.
Energy Detect Admin mode Enable or disable Energy Detect mode on the port. When this mode is
enabled, when the port link is down, the PHY automatically goes down for a
short period of time, then wakes up to check link pulses. This allows the
switch to perform autonegotiation and save power consumption when no
link partner is present.
Energy Detect Operational Status Current operational status of the Energy Detect mode.
EEE Admin mode Enable or disable Energy Efficient Ethernet mode on the port. With EEE
mode enabled, the port transitions to low power mode during link idle
conditions.