User Manual
Table Of Contents
- Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports
- Contents
- 1. Getting Started
- Switch Management Options and Default Management Mode
- Available Publications
- Web Browser Requirements and Supported Browsers
- User-Defined Fields
- Interface Naming Conventions
- Access the Switch
- Change the Management Mode of the Switch
- Register the Switch
- How to Configure Interface Settings
- Local Browser Interface Device View
- 2. Configure System Information
- View and Configure the Switch Management Settings
- View or Define System Information
- View the Switch CPU Status
- Configure the CPU Thresholds
- Configure the IPv4 Address for the Network Interface and Management VLAN
- Configure the IPv6 Address for the Network Interface
- View the IPv6 Network Neighbor
- Configure the Time Settings
- Configure Denial of Service Settings
- Configure DNS Settings
- Configure Green Ethernet Settings
- Manage the Bonjour Settings and View Bonjour Information
- Control the LEDs
- Use the Device View
- Configure Power over Ethernet
- Configure Link Layer Discovery Protocol
- Configure DHCP L2 Relay and DHCP Snooping
- Set Up PoE Timer Schedules
- View and Configure the Switch Management Settings
- 3. Configure Switching
- 4. Configuring Routing
- 5. Configure Quality of Service
- 6. Manage Device Security
- Management Security Settings
- Configure Management Access
- Configure Port Authentication
- Set Up Traffic Control
- Configure Access Control Lists
- Use the ACL Wizard to Create a Simple ACL
- Configure a Basic MAC ACL
- Configure MAC ACL Rules
- Configure MAC Bindings
- View or Delete MAC ACL Bindings in the MAC Binding Table
- Configure an IP ACL
- Configure Rules for a Basic IP ACL
- Configure Rules for an Extended IP ACL
- Configure an IPv6 ACL
- Configure Rules for an IPv6 ACL
- Configure IP ACL Interface Bindings
- View or Delete IP ACL Bindings in the IP ACL Binding Table
- Configure VLAN ACL Bindings
- 7. Perform Maintenance Tasks
- 8. Manage Power over Ethernet
- 9. Monitor the System
- A. Configuration Examples
- B. Hardware Specifications and Default Values
Configuring Routing
180
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports
14. In the Adv NS Interval field, specify the retransmission time of router advertisements that
are sent from the interface.
A value of 0 means the interval is not specified. The range of the neighbor solicit interval
is 1000 to 4294967295. The default is 0.
15. In the Adv Reachable Interval field, specify the router advertisement time.
This is the time allocated to consider the neighbors reachable after ND confirmation. The
range of reachable time is 0 to 3600000. The default is 0.
16. Use the Adv Interval field to specify the maximum time allowed between sending router
advertisements from the interface.
The range of the maximum advertisement interval is 4 to 1800. The default value is 600.
17. From the Adv Managed Config Flag menu, specify the setting for the router advertisement
managed address configuration flag.
When the selection is Enable, end nodes use DHCPv6. When the selection is Disable,
end nodes autoconfigure addresses. The default value is Disable.
18. From the Adv Other Config Flag menu, select to enable or disable the router
advertisement other stateful configuration flag.
The default value is Disable.
19. From the Router Preference menu, specify the router preference advertisement on an
interface.
The default value is Medium.
20. From the Adv Suppress Flag menu, select to enable or disable the router advertisement
suppression on an interface.
The default value is Disable.
21. From the Destination Unreachables menu, select to enable or disable the mode for
sending ICMPv6 destination unreachable messages on this interface.
If this mode is disabled, the interface does not send ICMPv6 destination unreachable
messages. The default value is Enable.
22. Click the Apply button.
Your settings are saved.
The following table describes the nonconfigurable information displayed on the page.
Table 51. IPv6 VLAN Configuration information
Field Description
Routing Mode Displays the routing mode of an interface. The default is Disable.
Operational Mode Specifies the operational state of an interface. The default value is
Disable.
Link State Indicates whether the link is up or down.