Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports M od els G C1 1 0 , GC1 1 0 P, G C 5 1 0 P, a nd G C 5 1 0 P P User Manual July 2018 202-11745-04 350 East Plumeria Drive San Jose, CA 95134 USA
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Support Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support to register your product, get help, access the latest downloads and user manuals, and join our community. We recommend that you use only official NETGEAR support resources. Conformity For the current EU Declaration of Conformity, visit http://kb.netgear.com/app/answers/detail/a_id/11621.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Contents Chapter 1 Getting Started Switch Management Options and Default Management Mode . . . . . . . . . . . . . 10 Available Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Web Browser Requirements and Supported Browsers . . . . . . . . . . . . . . . . . . . . 11 User-Defined Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View LLDP Neighbors Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure DHCP L2 Relay and DHCP Snooping . . . . . . . . . . . . . . . . . . . . . . . . . . Configure a DHCP L2 Relay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure DHCP Snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View and Search the MAC Address Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Set the Dynamic Address Aging Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Add a Static MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Remove a Static MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure DiffServ IPv6 Class Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 Configure a DiffServ Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Configure the DiffServ Service Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 View DiffServ Service Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Chapter 7 Perform Maintenance Tasks Reboot the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 Reset the Switch to Its Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . 329 Export a File From the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 Export a File to the TFTP Server. . . . . . . . . . .
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Manage the Server Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 View or Clear the Trap Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 View or Clear the Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386 Configure Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. 1 Getting Started This manual describes how you can configure and monitor the following NETGEAR Insight managed switches by using the local browser–based management interface: • GC110. 8-Port Gigabit Ethernet Insight Managed Smart Cloud Switch with 2 SFP Fiber Ports • GC110P. 8-Port Gigabit Ethernet PoE Insight Managed Smart Cloud Switch with 2 SFP Fiber Ports • GC510P. 8-Port Gigabit Ethernet PoE+ Insight Managed Smart Cloud Switch with 2 SFP Fiber Ports • GC510PP.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Switch Management Options and Default Management Mode If you prefer, you can use the switch as a plug-and-play device, so you do not need to set up a custom configuration. Just connect power, connect to your network and to your other devices, and you’re done. The switch is designed for management by the NETGEAR Insight app on a smartphone or tablet.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports the device remotely or through the cloud, you can return the management mode to NETGEAR Insight Mobile App and Insight Cloud Portal at any time so that you can manage the switch with the Insight app or Insight Cloud portal.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports User-Defined Fields In the local browser interface, user-defined fields can contain 1 to 159 characters, unless otherwise noted in the field label on the configuration page. All alphanumeric and special characters can be used except for the following (unless specifically noted for that feature): Table 1. Disallowed characters in user-defined fields Character Definition Character Definition \ Backslash < Less than / F
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Access the Switch When you use the local browser interface, for easiest access, we recommend that you cable the switch to a network with a router or DHCP server that assigns IP addresses, power on the switch, and then use a computer that is connected to the same network as the switch (on-network, see Access the Switch On-Network on page 13).
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 8. Double-click GCmodel (xx:xx:xx:xx:xx:xx) (where GCmodel is the model number of your switch and xx:xx:xx:xx:xx:xx is the MAC address of the switch). The login page of the local browser interface opens. 9. Enter the password. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The General page displays. 6. Click the Advanced tab. The Advanced page displays. 7. Select the Include Bonjour in the Bookmarks Menu check box. 8. Close the Advanced page. 9.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To access the DHCP server and use a web browser to access the switch that is connected to a network: 1. Cable the switch to a network with a router or DHCP server that manages IP addresses. 2. Power on the switch. The DHCP server assigns the switch an IP address. 3. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection. 4.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Determine the Switch IP Address Using the NETGEAR Insight App and Access the Switch On-Network To use the NETGEAR Insight app and a web browser to access the switch that is connected to a network: 1. On your iOS or Android mobile device, go to the app store, search for NETGEAR Insight, and download the app. 2.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 14. Select the Direct Connect Web-browser Interface radio button. 15. Click the Apply button. Your settings are saved. The System Information page closes, any current Insight-manageable device settings are saved to the cloud server, and the login window displays again. 16. When prompted, enter the password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 11. Select the Direct Connect Web-browser Interface radio button. 12. Click the Apply button. Your settings are saved. The System Information page closes, any current Insight-manageable device settings are saved to the cloud server, and the login window displays again. 13. When prompted, enter the password. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. Click the OK button to close the notification. The System Information page displays. 7. Select the Direct Connect Web-browser Interface radio button. 8. Click the Apply button. Your settings are saved. The System Information page closes, any current Insight-manageable device settings are saved to the cloud server, and the login window displays again. 9. When prompted, enter the password. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Change the Management Mode to Direct Connect Web-browser Interface Note: If you already accessed the local browser interface (see Access the Switch on page 13), you can skip this section. To change the management mode of the switch to Direct Connect Web-browser Interface: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Change the Management Mode Back to NETGEAR Insight Mobile App and Insight Cloud Portal To change the management mode of the switch back to NETGEAR Insight Mobile App and Insight Cloud Portal: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not claim (register) the device and add it to an Insight network using the Insight app, you can manually register the switch using the local browser interface as described in the following procedure or you can visit he NETGEAR website for registration at https://my.netgear.com/register/register.aspx. To register the switch through the local browser interface: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Use these links as follows: • To display all ports, click the 1 link. The LAGs are not displayed. • To display all LAGs, click the LAGS link. The ports are not displayed. • To display all ports and LAGs, click the All link. The procedures in this section describe how to select the ports and LAGs to configure. The procedures assume that you are already logged in to the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 3. Configure the desired settings. 4. Click the Apply button. Your settings are saved. Local Browser Interface Device View The Device View page in the local-only mode browser interface displays the ports and system LEDs on the switch. This graphic provides an alternate way to navigate to configuration and monitoring options.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Solid gray. The port is not connected. This is the default state. • Solid green. The port is operating at its maximum speed. • Blinking green. The port is transmitting or receiving traffic at its maximum speed • Solid amber The port is operating at below its maximum speed. • Blinking amber. The port is transmitting or receiving traffic below its maximum speed.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The previous figure shows the Device View page for model GC510P. 7. To display the main menu that contains the same options as the navigation menu at the top of the page, right-click the graphic without clicking a specific port. The previous figure shows the Device View page for model GC510P. 8. To return to the Device View page, select System > Device View from the System Information page.
2.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View and Configure the Switch Management Settings This section describes how to display the switch status and specify some basic switch information, such as the management interface IP address, system clock settings, and DNS information.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Define the following fields: • System Name. Enter the name to identify this switch. You can use up to 255 alphanumeric characters. • System Location. Enter the location of this switch. You can use up to 255 alphanumeric characters. • System Contact. Enter the contact person for this switch. You can use up to 255 alphanumeric characters. 6. Click the Apply button. Your settings are saved.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View the Temperature Sensor Information You can view the current temperature of the temperature sensors. The temperature is instant and can be updated with the latest information about the switch when you click the Refresh button. The maximum temperature of the temperature sensors depends on the actual hardware. To view temperature information: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View the Fan Status Note: The fan status information is available for model GC510PP only. You can view the status of the fans. These fans remove the heat generated by the power, CPU, and other components, and allow the switch to function normally. To view the fan status: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View the Power Supplies You can view s the status of the power supplies. To view the power supplies status: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure the CPU Thresholds The CPU utilization threshold notification feature allows you to configure thresholds that, when exceeded, trigger a notification. The notification occurs through SNMP trap and syslog messages. To configure the CPU thresholds: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure the IPv4 Address for the Network Interface and Management VLAN You can configure network information for the network interface, which is the logical interface used for in-band connectivity with the switch through any of the switch’s ports. You also use the IPv4 address of the network interface to connect to the switch through the local browser interface.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Default Gateway. The default gateway for the IP interface. The default value is 192.168.0.254. 8. Specify the VLAN ID for the management VLAN. The management VLAN is used to establish an IP connection to the switch from a computer that is connected to a port in the same VLAN. If not specified, the active management VLAN ID is 1 (default), which allows an IP connection to be established through any port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports When in-band connectivity is established, you can change the IPv6 information through the local browser interface. To configure the IPv6 address for the network interface: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports b. In the EUI64 menu, select True to enable the Extended Universal Identifier (EUI) flag for IPv6 address, or select False to omit the EUI flag. c. Click the Add button. 10. Click the Apply button. Your settings are saved. View the IPv6 Network Neighbor You can view information about the IPv6 neighbors that the switch discovers through the Neighbor Discovery Protocol (NDP). To view the IPv6 neighbor table: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 9. IPv6 network interface neighbor table information (continued) Field Description Neighbor State The state of the neighboring switch: • reachable (1). The neighbor is reachable from the switch. • stale (2). Information about the neighbor is scheduled for deletion. • delay (3). No information was received from the neighbor during the delay period. • probe (4). The switch is attempting to probe the neighbor.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Note: If you do not enter a date and time, the switch calculates the date and time using the CPU’s clock cycle. 9. Click the Apply button. Your settings are saved. Configure the Time Settings With SNTP To configure the time by using SNTP: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Broadcast. SNTP operates in the same manner as multicast mode but uses a local broadcast address instead of a multicast address. The broadcast address provides a single-subnet scope while a multicast address provides an Internet-wide scope. The default value is Disable. 8.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports See the description for Time Zone Name in Step 14 for more information. The allowed range is 0 to 59. The default value is 0. 17. Click the Apply button. Your settings are saved. Modify the Global SNTP Settings To modify the global SNTP settings: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The allowed range is 1025 to 65535 and the value 123. The default value is 123. When the default value is configured, the actual client port value used in SNTP packets is assigned by the operating system. 8. In the Unicast Poll Interval field, specify the number of seconds between unicast poll requests expressed as a power of 2. The allowed range is 6 to 10. The default value is 6. 9.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View SNTP Global Status When you select the SNTP option as the clock source, the SNTP global status is displayed below the SNTP Global Configuration section of the page. The SNTP Global Status table displays information about the system’s SNTP client. To view SNTP global status: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 10. SNTP Global Status information (continued) Field Description Last Attempt Status The status of the last SNTP request or unsolicited message for both unicast and broadcast modes. If no message was received from a server, a status of Other is displayed. These values are appropriate for all operational modes. • Other. The status of the last request is unknown. • Success.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following is an example of strata: • Stratum 0. A real-time clock is used as the time source, for example, a GPS system. • Stratum 1. A server that is directly linked to a Stratum 0 time source is used. Stratum 1 time servers provide primary network time standards. • Stratum 2. The time source is distanced from the Stratum 1 server over a network path.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select System > Management > Time > SNTP Server Configuration. The SNTP Server Configuration page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The SNTP Server Status table displays status information about the SNTP servers configured on your switch. The following table describes the SNTP Server Global Status information. Table 11. SNTP Server Status information Field Description Address All the existing server addresses. If no server configuration exists, a message stating that no SNTP server exists displays on the page.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select System > Management > Time > SNTP Server Configuration. The SNTP Server Configuration page displays. 6. Select the check box next to the configured server. 7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure the daylight saving time settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • • If you select the DayLight Saving (DST) Recurring, Recurring EU, or Recurring USA radio button, configure the settings that are shown in the following table. Field Description Begins At These fields are used to configure the start values of the date and time. • Week. Configure the start week. • Day. Configure the start day. • Month. Configure the start month. • Hours. Configure the start hour. • Minutes.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View the DayLight Saving Time Status The Daylight Saving (DST) Status section shows information about the summer time settings and whether the time shift for summer time is currently in effect. To view the daylight saving time status: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 12. Daylight Saving (DST) Status information (continued) Field Description Zone The zone acronym. This field is not displayed when daylight saving time is disabled. Daylight Saving (DST) in Effect Indicates whether daylight saving time is in effect. Configure Denial of Service Settings You can configure the Denial of Service (DoS) settings for the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure Denial of Service The Denial of Service Configuration page allows you to select which types of DoS attacks the switch monitors and blocks. To configure individual DoS settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Denial of Service ICMP Fragment. Enabling ICMP Fragment DoS prevention causes the switch to drop ICMP fragmented packets. • Denial of Service SIP=DIP. Enabling SIP=DIP DoS prevention causes the switch to drop packets with a source IP address equal to the destination IP address. • Denial of Service SMAC=DMAC.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table displays DNS Server Configuration information. Table 13. DNS Server Configuration information Field Description ID The identification of the DNS Server. Preference Shows the preference of the DNS server. The preferences are determined by the order in which they were entered.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Remove an Entry From the Dynamic Host Mapping Table To remove an entry from the dynamic host mapping table: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select System > Management > DNS > Host Configuration. The DNS Host Configuration page display. 6. Select the check box next to the entry to update. 7. Enter the new information in the appropriate field. 8. Click the Apply button. Your settings are saved. 9. To clear all the dynamic host name entries from the list, click the Clear button.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The Green Ethernet Configuration page displays. 6. Select the Auto Power Down Mode Disable or Enable radio button. By default, this mode is disabled. When a port link is down, the underlying physical layer goes down for a short period and then checks for port link pulses again so that autonegotiation remains possible. In this way, the switch saves power when no link partner is present for the port. 7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. Do one of the following: • In the Go To Interface field, enter the port using the respective naming convention (for example, g1 or l1), and click the Go button. The entry corresponding to the specified interface is selected. For more information about naming conventions, see Interface Naming Conventions on page 12. • Select the port. 7. Select the Auto Power Down Mode Disable or Enable radio button.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select System > Management > Green Ethernet > Green Ethernet Details. The Green Ethernet Details page displays. 6. From the Interface menu, select the interface. 7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 15. Green Ethernet Local Device Information (continued) Field Description Tw_sys_tx (uSec) Integer that indicates the value of Tw_sys that the local system can support. Tw_sys_tx Echo (uSec) Integer that indicates the remote system’s Transmit Tw_sys that was used by the local system to compute the Tw_sys that it wants to request from the remote system.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 5. Select System > Management > Green Ethernet >Green Ethernet Details. The Green Ethernet Details page displays. 6. Scroll down to the Remote Device Information section. 7. Select the interface. The following table describes the nonconfigurable fields. Table 16.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select System > Management > Green Ethernet > Green Ethernet Summary. The Green Ethernet Statistics Summary page displays. 6. To refresh the page, click the Refresh button. The following table describes the nonconfigurable fields. Table 17. Green Ethernet Statistics Summary information Field Description Current Power Consumption (mW) Estimated power consumption by all ports of the switch in mWatts.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select System > Management > Green Ethernet > Green Ethernet LPI History. The Green Ethernet LPI History page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Manage the Bonjour Settings and View Bonjour Information A Mac OS device that supports Bonjour can discover the switch in the network so that you can find the switch IP address and log in to the local browser interface of the switch. Bonjour is enabled by default on the switch. You can disable Bonjour for security reasons. Manage the Bonjour Settings To manage the Bonjour settings: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select System > Management > LED Control. 6. Select the System LEDs On or Off radio button.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • View Local LLDP Information on page 79 • View LLDP Neighbors Information on page 81 LLDP is a one-way protocol without any request/response sequences. Information is advertised by stations implementing the transmit function, and is received and processed by stations implementing the receive function. The transmit and receive functions can be enabled or disabled separately per port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • TLV Advertised Interval. The number of seconds between transmissions of LLDP advertisements. • Hold Multiplier. The transmit interval multiplier value, in which the transmit hold multiplier multiplied by the transmit interval is the time to live (TTL) value that the switch advertises to its neighbors. • Reinitializing Delay.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. Select one or more interfaces by taking one of the following actions: • To configure a single interface, select the check box associated with the port, or type the port number in the Go To Interface field and click the Go button. • To configure multiple interfaces with the same settings, select the check box associated with each interface.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 20. LLDP-MED network policy information (continued) Field Description User Priority The priority associated with the policy. DSCP The DSCP associated with a particular policy type. Configure the LLDP-MED Port Settings You can enable LLDP-MED mode on an interface and configure its properties. To configure LLDP-MED settings for a port: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 8. Click the Apply button. Your settings are saved. LLDP-MED Neighbors Information You can display the LLDP-MED neighbor or remote device information for an interface. To view LLDP-MED Neighbor Information: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Field Description Device Class Specifies device class as advertised by the device remotely connected to the port. Network Policies Information This section of the page specifies if network policy TLV is received in the LLDP frames on this port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Field Description This section of the page specifies if extended PSE TLV is received in LLDP frame on this port. Device Type Specifies the remote device’s PoE device type connected to this port. Power Source Specifies the remote port’s PSE power source. Power Priority Specifies the remote port’s PSE power priority. Power Value Specifies the remote port’s PSE power value in tenths of watts.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the LLDP device information and port summary information. Field Description Device Information Chassis ID Subtype The type of information used to identify the switch in the Chassis ID field. Chassis ID The hardware platform identifier for the switch. System Name The user-configured system name for the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Field Description Operational MAU Type The Medium Attachment Unit (MAU) type. The MAU performs physical layer functions, including digital data conversion from the Ethernet interface collision detection and bit injection into the network. MED Details Capabilities Supported The MED capabilities enabled on the port. Current Capabilities The TLVs advertised by the port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If no information was received from a neighbor device, or if the link partner is not LLDP-enabled, no information displays. The following table describes the information that displays for all LLDP neighbors that were discovered. Field Description MSAP Entry The Media Service Access Point (MSAP) entry number for the remote device.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Field Description System Capabilities The system capabilities of the remote system. Managed Addresses Address SubType The type of the management address. Address The advertised management address of the remote system. Interface SubType The port subtype. Interface Number The port on the remote device that sent the information.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Field Description Model Name The model name advertised by the remote device. Asset ID The asset ID advertised by the remote device. Location Information Civic The physical location, such as the street address, that the remote device advertised in the location TLV, for example, 123 45th St. E. The field value length range is 6–160 characters.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure a DHCP L2 Relay DHCP relay agents eliminate the need to connect to a DHCP server on each physical network. Relay agents populate the giaddr field and also append the Relay Agent Information option to the DHCP messages. DHCP servers use this option for IP addresses and other parameter assignment policies. These DHCP relay agents are typically IP routing-aware devices and are referred to as Layer 3 relay agents.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure the DHCP L2 relay settings for a VLAN: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select System> Services > DHCP L2 Relay > DHCP L2 Relay Interface Statistics.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports trusted interface is an interface that is configured to receive only messages from within the network. DHCP snooping acts like a firewall between untrusted hosts and DHCP servers. It also provides way to differentiate between untrusted interfaces connected to the end user and trusted interfaces connected to the DHCP server or another switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select System> Services > DHCP Snooping > Interface Configuration. The DHCP Snooping Interface Configuration page displays. 6. To display information for all ports and LAGs, click the All link. 7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure static DHCP bindings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure the Persistent Location of the DHCP Snooping Bindings Database You can configure the persistent location of the DHCP snooping bindings database. The bindings database can be stored locally on the device or on a remote system somewhere else in the network. The device must be able to reach the IP address of the remote system to send bindings to a remote database.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View or Clear the DHCP Snooping Statistics You can view and clear per-interface statistics about the DHCP messages filtered by the DHCP snooping feature on untrusted interfaces. To view or clear the DHCP snooping statistics: 1. Connect your computer to the same network as the switch.
3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure Port Settings You can view, configure, and monitor the physical port information for the ports (that is, the physical interfaces) on the switch. To configure port settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Note: After you change the autonegotiation mode, the switch might be inaccessible for a number of seconds while the new settings take effect. 11. In the Speed field, specify the speed value for the selected port. - Auto. All supported speeds. If you select Auto, the duplex mode and speed are set by the autonegotiation process. The port’s maximum capability (full duplex and 1000 Mbps) are advertised.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Flow control helps to prevent data loss when the port cannot keep up with the number of frames being switched. When you enable flow control, the switch can send a pause frame to stop traffic on the port if the amount of memory used by the packets on the port exceeds a preconfigured threshold and responds to pause requests from partner devices.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports A LAG interface can be either static or dynamic, but not both. All members of a LAG must participate in the same protocols. A static port channel interface does not require a partner system to be able to aggregate its member ports. The switch supports static LAGs. When a port is added to a LAG as a static member, the port neither transmits nor receives LACPDUs.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • 2 Dest MAC, VLAN, EType, incoming port. This mode uses the destination MAC address, VLAN, EtherType, and incoming port that are associated with the packet. • 3 Src/Dest MAC, VLAN, EType, incoming port. This mode uses the source and destination MAC addresses, VLAN, EtherType, and incoming port that are associated with the packet. This is the default mode. • 4 Src IP and Src TCP/UDP Port fields.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure LAG Membership You can select two or more full-duplex Ethernet links to be aggregated together to form a link aggregation group (LAG), which is also known as a port channel. The switch can treat the port channel as a single link. To configure LAG membership: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Set the LACP System Priority The LACP configuration page is used to set the LACP system priority. To configure LACP: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Switching> LAG > Advanced > LACP Port Configuration. The LACP Port Priority page displays.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports packet can either reject it or insert a tag using its default VLAN ID. A given port can handle traffic for more than one VLAN, but it can support only one default VLAN ID. You can define VLAN groups stored in the VLAN membership table. The switch supports up to 256 VLANs. VLAN 1 is created by default and is the default VLAN of which all ports are members. VLAN 4089 is also created by default and is the Auto-Video VLAN.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The VLAN is added to the switch. 10. Click the Apply button. Your settings are saved. Delete a VLAN To delete a VLAN from the switch: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Switching> VLAN > Advanced > VLAN Trunking Configuration.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Note the following: • Use a dash (–) to specify a range. • Use a comma (,) to separate VLANs in a list. Spaces are not permitted. • A zero value means that you want to clear the allowed VLANs. • The All value means that you want to set all VLANs to the range (1 to 4093). 12. Click the Apply button. Your settings are saved. The following table shows the nonconfigurable information on the page. Table 25.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. In the VLAN ID menu, select the VLAN ID. 7. In the Group Operation menu, select one of the following options, which applies to all ports in the VLAN: • Untag All. For all ports that are members of the VLAN, tags are removed from all egress packets. • Tag All. For all ports that are members of the VLAN, all egress packets are tagged. • Remove All. All ports are removed from the VLAN. 8.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the nonconfigurable information displayed on the page. Table 26. Advanced VLAN membership Field Definition VLAN Name The name for the VLAN that you selected. It can be up to 32 alphanumeric characters long, including blanks. VLAN ID 1 always uses the name Default. VLAN Type The type of the VLAN you selected: • Default (VLAN ID = 1). Always present. • Static. A VLAN that you configured.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 27. VLAN status (continued) Field Definition VLAN Type The VLAN type: • Default (VLAN ID = 1). Always present. • Static. A VLAN that you added. • Auto-Video. (VLAN ID = 4089). Always present. Member Ports The ports that are included in the VLAN. Configure Port PVID Settings You can assign a port VLAN ID (PVID) to an interface. The following requirements apply to a PVID: • You must define a PVID for all ports.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • To configure all interfaces with the same settings, select the check box in the heading row. 8. In the PVID field, specify the VLAN ID to assign to untagged or priority-tagged frames received on this port. The default is 1. 9. In the VLAN Member field, specify the VLAN ID or list of VLANs of a member port. VLAN IDs range from 1 to 4093. The default is 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the nonconfigurable fields. Table 28. Nonconfigurable fields on the PVID Configuration page Field Description Current Ingress Filtering Indicates whether ingress filtering is enabled for the interface. Untagged VLANs The number of untagged VLANs for the interface. Tagged VLANs The number of tagged VLANs for the interface. Forbidden VLANs The number of forbidden VLANs for the interface.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 5. Select Switching> VLAN > Advanced > MAC Based VLAN. The MAC Based VLAN Configuration page displays. 6. In the MAC Address field, enter a valid MAC address to be bound to a VLAN ID. This field is configurable only when a MAC-based VLAN is created. 7. In the VLAN ID field, specify a VLAN ID in the range of 1 to 4093. 8. Click the Add button.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports untagged packets are assigned to VLAN 1. You can override this behavior by defining either port-based VLANs or protocol-based VLANs, or both. Tagged packets are always handled according to the IEEE 802.1Q standard and are not included in protocol-based VLANs. If you assign a port to a protocol-based VLAN for a specific protocol, untagged frames received on that port for that protocol are assigned the protocol-based VLAN ID.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The ID can be any number in the range of 1 to 4093. All the ports in the group assign this VLAN ID to untagged packets received for the protocols that you included in this group. 10. Click the Add button. The protocol-based VLAN group is added to the switch. 11. Click the Apply button. Your settings are saved. The following table describes the nonconfigurable information displayed on the page. Table 29.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Your settings are saved. 9. To view the members of the group, click the Current members button. A pop-up window opens and displays the list of current members. Configure a Voice VLAN You can configure the parameters for a voice VLAN configuration. To configure a voice VLAN: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • VLAN ID. Configure the phone to send tagged voice traffic. With this selection, you can enter a Dot1p value in the Value field. • Dot1p. Configure voice VLAN 802.1p priority tagging for voice traffic. With this selection, you must enter a dot1p value in the Value field. • Untagged. Configure the phone to send untagged voice traffic. 9. In the Value field, enter the VLAN ID or dot1p value.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports VoIP frames that are received on ports that for which the Auto-VoIP feature is enabled are marked with the specified CoS traffic class value. To configure protocol-based port settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure Auto-VoIP OUI-Based Properties With Organizationally Unique Identifier (OUI)–based Auto-VoIP, voice prioritization is provided based on OUI bits. To configure Auto-VoIP OUI-based properties: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure OUI-Based Port Settings The port settings page allows you to configure the OUI port settings. To configure OUI-based port settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Manage the OUI Table Device hardware manufacturers can include an OUI in a network adapter to help identify a hardware device. The OUI is a unique 24-bit number assigned by the IEEE registration authority.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. In the Telephony OUI(s) field, specify the VoIP OUI prefix to be added in the format AA:BB:CC. Up to 128 OUIs can be configured. 7. In the Description field, enter the description for the OUI. The maximum length of description is 32 characters.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. Click the Delete button. The telephony OUI entries are removed. Display the Auto-VoIP Status You can display the Auto-VoIP status. To view the Auto-VoIP status: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Spanning Tree Protocol Overview Classic STP provides a single path between end stations, avoiding and eliminating loops. For information on configuring Common STP, see Configure CST Port Settings on page 128. Multiple Spanning Tree Protocol (MSTP) supports multiple instances of spanning tree to efficiently channel VLAN traffic over different interfaces.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. Configure the following options: • Spanning Tree State. Enable or disable the spanning tree operation on the switch. • STP Operation Mode. Specify the STP version for the switch. The options are STP, RSTP, and MSTP. For more information, see Spanning Tree Protocol Overview on page 125. • Configuration Name. Specify an identifier used to identify the configuration currently being used.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 31. STP configuration status (continued) Field Description Forward Delay (secs) The derived value of the Root Port Bridge Forward Delay parameter. Hold Time (secs) Minimum time in seconds between the transmission of configuration BPDUs. CST Regional Root Priority and base MAC address of the CST regional root. CST Path Cost Path cost to the CST tree regional root.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports implementing a topological change. The valid range is 6–40, and the value must be less than or equal to (2 * Bridge Forward Delay) – 1 and greater than or equal to 2 * (Bridge Hello Time +1). The default value is 20. • Bridge Hello Time (secs). The bridge hello time for the Common and Internal Spanning Tree (CST), which indicates the time in seconds a root bridge must wait between configuration messages.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Switching > STP > Advanced > CST Port Configuration. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 13. In the Priority field, specify the priority for a particular port within the CST. The port priority is set in multiples of 16. For example if you attempt to set the priority to any value between 0 and 15, it is set to 0. If you try to set it to any value between 16 and (2*16 – 1), it is set to 16, and so on. The range is 0 to 240. The default value is 128. 14.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 5. Select Switching > STP > Advanced > CST Port Status. The CST Port Status page displays. 6. To refresh the page with the latest information about the switch, click the Refresh button. The following table describes the CST Status information displayed on the page. Table 34.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View Rapid STP Information You can view information about the Rapid Spanning Tree (RSTP) port status. To view information about RSTP: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Manage MST Settings You can configure a multiple spanning tree (MST) on the switch. Configure an MST Instance To configure an MST instance: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports For each configured instance, the information described in the following table displays on the page. Table 36. MST configuration Field Description Bridge Identifier The bridge identifier for the selected MST instance. It is made up using the bridge priority and the base MAC address of the bridge. Last TCN The time in day:hour:minute:second format since the topology of the selected MST instance last changed.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. Update the values. 8. Click the Apply button. Your settings are saved. Delete an MST Instance To delete an MST instance: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the read-only MST port configuration information displayed on the Spanning Tree CST Configuration page. Table 37. MST port status information Field Description Operational Port Path Cost The operational path cost for the port in the MST instance. Auto-calculated Port Path Cost Indicates whether the path cost is automatically calculated (Enabled) or not (Disabled).
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View STP Statistics You can view information about the number and type of bridge protocol data units (BPDUs) transmitted and received on each port. To view Spanning Tree statistics: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure Multicast Multicast IP traffic is traffic that is destined to a host group. Host groups for IPv4 multicast are identified by class D addresses, which range from 224.0.0.0 to 239.255.255.255. Host groups for IPv6 multicast are identified by the prefix ff00::/8. View or Clear the MFDB Table The Multicast Forwarding Database holds the port membership information for all active multicast address entries.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the information in the MFDB table. Table 39. MFDB table information Field Description MAC Address The multicast MAC address for which you requested data. VLAN ID The VLAN ID to which the multicast MAC address is related. Component The component that is responsible for this entry in the Multicast Forwarding Database.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the MFDB Statistics fields. Table 40. MFDB Statistics information Field Description Max MFDB Table Entries The maximum number of entries that the Multicast Forwarding Database table can hold. Most MFDB Entries Since The largest number of entries that were present in the Multicast Forwarding Last Reset Database table since last reset. This value is also known as the MFDB high-water mark.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure IGMP Snooping Internet Group Management Protocol (IGMP) snooping is a feature that allows a switch to forward multicast traffic intelligently. Multicast IP traffic is traffic that is destined to a host group. Host groups are identified by class D IP addresses, which range from 224.0.0.0 to 239.255.255.255.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure IGMP Snooping Globally You can configure the parameters for IGMP snooping, which is used to build forwarding lists for multicast traffic. To configure IGMP snooping globally: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 41. IGMP Snooping Configuration information (continued) Field Description VLAN IDs Enabled For IGMP Snooping The IDs of the VLANs that are enabled for IGMP snooping. VLAN IDs Enabled For IGMP Snooping Querier The IDs of the VLANs that are enabled for IGMP snooping querier. Configure IGMP Snooping for Interfaces To configure IGMP snooping for interfaces: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Enter a value between 1 and 3600 seconds. The default is 260 seconds. 10. In the Max Response Time field, specify the time that the switch must wait after sending a query on an interface because it did not receive a report for a particular group on that interface. Enter a value greater or equal to 1 and less than the group membership interval in seconds. The default is 10 seconds.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Enter six two-digit hexadecimal numbers separated by colons, for example 00:01:23:43:45:67. 7. Click the Go button. If the address exists, the entry is displayed. An exact match is required. 8. To refresh the page with the latest information about the switch, click the Refresh button. 9. To clear the information, click the Clear button. The following table describes the information in the IGMP snooping table. Table 42.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The IGMP Snooping VLAN Configuration page displays. 6. To enable IGMP snooping on a VLAN, in the VLAN ID field, enter the VLAN ID. 7. Configure the IGMP snooping values: • Admin Mode. Enable or disable IGMP snooping for the specified VLAN ID. The default is Disable. • Fast Leave Mode. Enable or disable the IGMP snooping fast leave mode for the specified VLAN ID. The default is Disable. • Host Timeout.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Switching> Multicast > IGMP Snooping > IGMP Snooping VLAN Configuration. The IGMP Snooping VLAN Configuration page displays. 6. Select the check box next to the VLAN ID.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports accordingly. It is required only if you want to make sure that the multicast router always receives IGMP packets from the switch in a complex network. To configure multicast router interfaces: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure the Global IGMP Snooping Querier Settings You can configure the global settings for an IGMP snooping querier. To configure the global IGMP snooping querier settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure an IGMP Snooping Querier for a VLAN You can configure an IGMP snooping querier for use with a VLAN on the network. To configure an IGMP querier snooping for a VLAN: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Remove an IGMP Snooping Querier From a VLAN You can remove an IGMP snooping querier from a VLAN. To remove an IGMP snooping querier from a VLAN: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 5. Select Switching> Multicast > IGMP Snooping Querier > Querier VLAN Status. The Querier VLAN Status page displays. 6. To refresh the page with the latest information about the switch, click the Refresh button. The following table describes the nonconfigurable information displayed on the page. Table 43.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports nodes. MLD is derived from IGMP; MLD version 1 (MLDv1) is equivalent to IGMPv2 and MLD version 2 (MLDv2) is equivalent to IGMPv3. MLD is a subprotocol of Internet Control Message Protocol version 6 (ICMPv6), and MLD messages are a subset of ICMPv6 messages, identified in IPv6 packets by a preceding Next Header value of 58.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. Click the Apply button. Your settings are saved. 8. To refresh the page with the latest information about the switch, click the Refresh button. The following table describes the nonconfigurable MLD Snooping Configuration fields. Table 44. MLD Snooping Configuration information Field Definition Multicast Control Frame Count The number of multicast control frames that were processed by the CPU.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • To configure all interfaces with the same settings, select the check box in the heading row. 8. From the Admin Mode menu, select to enable or disable the interface mode for the selected interface for MLD snooping for the switch. The default is Disable. 9.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Switching> Multicast > MLD Snooping > MLD VLAN Configuration. The MLD VLAN Configuration page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 5. Select Switching> Multicast > MLD Snooping > MLD VLAN Configuration. The MLD VLAN Configuration page displays. 6. Select the check box for the VLAN ID. 7. Click the Delete button. Your settings are saved. MLD snooping is no longer supported on the VLAN. The VLAN itself is not deleted.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure a Multicast Router VLAN for MLD Snooping To configure a multicast router VLAN for MLD snooping: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Switching> Multicast > MLD Snooping > Querier Configuration. The MLD Snooping Querier Configuration page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Switching> Multicast > MLD Snooping > Querier VLAN Configuration. The MLD Snooping Querier VLAN Configuration page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Remove an MLD Snooping Querier From a VLAN You can remove an MLD snooping querier from a VLAN. To remove an MLD snooping querier from a VLAN: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 46. MAC Address Table information (continued) Field Description Interface The interface on which the address was learned. Status The status of this entry, which can be one of the following: • Static. The instance was added by the system or a user and cannot be relearned. • Learned. The instance was learned, and is being used. • Management.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Add a Static MAC Address You can manually add MAC addresses to the MAC address table. Such MAC addresses are static MAC addresses. To add a static MAC address: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Switching > Address Table > Advanced > Static MAC Address.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports enable loop protection globally before you can enable and configure it at the interface level. Loop protection is supported on physical interfaces and static LAG interfaces, but not on dynamic LAG interfaces. Configure Global Layer 2 Loop Protection To configure global Layer 2 loop protection: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 10. Click the Apply button. Your settings are saved. Configure Layer 2 Loop Protection on a Port To configure Layer 2 loop protection on a port: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • In the Go To Port field, type the port number, for example g18, and click the Go button. 7. In the Port field, select the port for which data is to be displayed or configured. 8. From the Keep Alive menu, select Enable or Disable to specify whether keep-alives are enabled on an interface. The default is Disable. 9.
4. 4 Configuring Routing This chapter covers the following topics.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports How the Switch Handles Routing For each incoming packet, the switch uses the destination MAC address to determine if the address matches a configured routing interface. If it does, the switch searches the host table for a matching destination IP address: • The host table contains a matching IP address.The packet is routed to the host. • The host table does not contain a matching IP address.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. Select the Routing Mode Enable radio button. 7. Click the Apply button. The following table describes the nonconfigurable information displayed on the page. Table 48. IP Configuration information Field Description Default Time to Live The default value that is inserted into the Time-To-Live field of the IP header of datagrams originated by the switch, if a TTL value is not supplied by the transport layer protocol.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the nonconfigurable information displayed on the page. Table 49. IP routing statistics information Field Description IpInReceives The total number of input datagrams received from interfaces, including those received in error.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 49. IP routing statistics information (continued) Field Description IpReasmFails The number of failures detected by the IP reassembly algorithm (for example, because of timing out, errors, and so on). This is not necessarily a count of discarded IP fragments because some algorithms can lose track of the number of fragments by combining them as they are received.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 49. IP routing statistics information (continued) Field Description IcmpOutParmProbs The number of ICMP Parameter Problem messages sent. IcmpOutSrcQuenchs The number of ICMP Source Quench messages sent. IcmpOutRedirects The number of ICMP Redirect messages sent. Because hosts do not send redirects, this counter is always zero for a host. IcmpOutEchos The number of ICMP Echo (request) messages sent.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The IPv6 Global Configuration page displays. 6. To globally enable IPv6 unicast routing, select the IPv6 Unicast Routing Enable radio button. By default, IPv6 unicast routing is disabled and the Disable radio button is selected. 7. In the Hop Limit field, enter the number for the unicast hop count that is used in IPv6 packets that originate in the switch. The value is also included in router advertisements.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • All Routes. Show all active IPv6 routes. • Best Routes Only. Show only the best active routes. • Configured Routes Only. Show only the manually configured routes. 7. To refresh the page with the latest information about the switch, click the Update button. The following table describes the nonconfigurable information displayed on the page. Table 50.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Routing> IPv6 > Advanced > VLAN Configuration. The IPv6 Global Configuration page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 14. In the Adv NS Interval field, specify the retransmission time of router advertisements that are sent from the interface. A value of 0 means the interval is not specified. The range of the neighbor solicit interval is 1000 to 4294967295. The default is 0. 15. In the Adv Reachable Interval field, specify the router advertisement time. This is the time allocated to consider the neighbors reachable after ND confirmation.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Manage IPv6 Prefixes for Advertisement on an IPv6 VLAN When you add an IPv6 prefix for advertisement on an IPv6 VLAN, the prefix is advertised on all interfaces that are members of the VLAN. You can change and remove existing IPv6 prefixes. Add an IPv6 Prefix for Advertisement on an IPv6 VLAN To add an IPv6 prefix for advertisement on an IPv6 VLAN: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 12. From the Onlink Flag menu, select Enable or Disable to specify whether the selected prefix can be used for on-link determination. The default is Enable. 13. From the Autonomous Flag menu, select Enable or Disable to specify whether the selected prefix can be used for autonomous address configuration. The default value is Enable. The Current State field displays the state of the IPV6 address.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 9. Click the Apply button. Your settings are saved. Remove an IPv6 Prefix From an IPv6 VLAN You can remove one or more IPv6 prefixes from an IPv6 VLAN. You cannot remove the default IPv6 prefix. To remove one or more IPv6 prefixes from an IPv6 VLAN: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Routing> IPv6 > Advanced > Statistics. The IPv6 Statistics page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 52. IPv6 Statistics information (continued) Field Description Received Datagrams Discarded Due To Truncated Data The number of input datagrams discarded because datagram frame did not carry enough data. Received Datagrams Discarded Other The number of input IPv6 datagrams for which no problems were encountered to prevent their continued processing, but that were discarded for reasons such as lack of buffer space.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the nonconfigurable ICMPv6 information displayed on the page. Table 53. ICMPv6 Statistics information Field Description Total ICMPv6 Messages Received The total number of ICMP messages received by the interface, which includes all those counted by IPv6IfIcmpInErrors.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 53. ICMPv6 Statistics information (continued) Field Description ICMPv6 Group Membership Reduction Messages Received The number of ICMPv6 Group Membership Reduction messages received by the interface. Total ICMPv6 Messages Transmitted The total number of ICMP messages that this interface attempted to send. This counter includes all those counted by icmpOutErrors.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 53. ICMPv6 Statistics information (continued) Field Description ICMPv6 Group Membership Reduction Messages Transmitted The number of ICMPv6 Group Membership Reduction messages sent. ICMPv6 Duplicate Address Detects The number of duplicate addresses detected by the interface. View the IPv6 Neighbor Table To view or clear the IPv6 Neighbor Table: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the nonconfigurable information displayed on the page. Table 54. IPv6 Neighbor Table information Field Description Interface The interface whose settings are displayed in the current table row. IPv6 Address The IPv6 address of the neighbor or interface. MAC Address The MAC address associated with an interface. isRtr Indicates whether the neighbor is a router.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports IPv6 routes associated with these management interfaces and IPv6 routes associated with routing interfaces. Configuration of 127-bit IPv6 prefixes on the routing/host IPv6 interfaces is supported. You can distinguishes between static routes by specifying a route preference value. A static route with a lower preference value is a more preferred static route.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 12. Click the Add button. The route is added. Change the Preference for a Static IPv6 Route To change the preference for a static IPv6 route: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Routing> IPv6 > Advanced > Static Route Configuration. The Configure Routes page displays. 6. Select one or more check boxes for static IPv6 routes. 7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the nonconfigurable information displayed on the page. Table 55. IPv6v Route Table information Field Description Number of Routes The total number of active routes in the route table. IPv6 Prefix The network prefix for the active route. Prefix Length The prefix length for the active route. Protocol The type of protocol for the active route.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The IPv6 Route Preference page displays. 6. In the Static field, specify the static route preference value for the switch. The range is 1 to 255. The default value is 1. 7. Click the Apply button. Your settings are saved. The Local field displays the local preference. Configure Routing VLANs You can configure the switch software with some ports supporting VLANs and some supporting routing.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure VLAN routing using the VLAN routing wizard: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • U (Untagged). Select the ports on which all frames transmitted for this VLAN are untagged. The ports that are selected are included in the VLAN. By default, the selection is blank, which means that the port is excluded from the VLAN. 10. In the LAG table, click each LAG once, twice, or three times to configure one of the following modes or reset the LAG to the default settings: • T (Tagged).
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The VLAN Routing Configuration page displays. The table displays any existing routing VLANs. 6. To add a routing VLAN by changing a regular VLAN into a routing VLAN, do the following: a. From the VLAN menu, select the VLAN that you want to configure for VLAN routing. The VLAN menu display all IDs of the VLANs that are configured on the switch. b. In the IP Address field, enter an IP address for the VLAN routing interface. c.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select Routing > VLAN > VLAN Routing Configuration. The VLAN Routing Configuration page displays. 6. From the VLAN list, select the VLAN. 7. Change the settings as needed. 8. Click the Apply button. Your settings are saved. Remove a Routing VLAN When you remove a routing VLAN, the VLAN becomes a regular VLAN. To remove a routing VLAN: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure the router discovery parameters: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Your settings are saved. Configure Routes and View Routes You can configure static and default routes and view the routes that the switch learned. To configure a static or default route: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 10. In the Preference field, specify the preference value for the route. Among routes to the same destination, the route with the lowest preference value is the route entered into the forwarding database. By specifying the preference of a static route, you can control whether a static route is more preferred or less preferred.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Routing > Routing Table > Route Configuration. The Configure Routes page displays.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • View Entries in the ARP Cache on page 203 • Create a Static ARP Entry on page 204 • Configure the Global ARP Settings on page 205 • Remove ARP Entries From the ARP Cache on page 206 View Entries in the ARP Cache You can view entries in the ARP table. To display entries in the ARP table: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table provides information included in the routing VLANs ARP cache section. Table 59. ARP cache information for routing VLANs Field Description IP Address The associated IP address of a device on a subnet attached to one of the switch's existing routing interfaces. Interface The routing interface associated with the ARP entry. MAC Address The unicast MAC address of the device.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The address must be the IP address of a device on a subnet attached to one of the switch’s existing routing interfaces. 7. In the MAC Address field, specify the unicast MAC address of the device. The format is six 2-digit hexadecimal numbers separated by colons, for example 00:06:29:32:81:40. 8. Click the Add button. The entry is added to the table.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Your settings are saved. Remove ARP Entries From the ARP Cache You can remove certain types of entries from the ARP table. To remove entries from the ARP table: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
5. Configure Quality of Service 5 In a switch, each physical port consists of one or more queues for transmitting packets on the attached network. Multiple queues per port are often provided to give preference to certain packets over others based on user-defined criteria. When a packet is queued for transmission in a port, the rate at which it is serviced depends on how the queue is configured and possibly the amount of traffic present in the other queues of the port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Manage Class of Service The Class of Service (CoS) queueing feature lets you directly configure certain aspects of switch queueing. This provides the desired QoS behavior for different types of network traffic when the complexities of DiffServ are not required. The priority of a packet arriving at an interface can be used to steer the packet to the appropriate outbound CoS queue through a mapping table.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select QoS> CoS > Basic > CoS Configuration. 6. Either configure the same CoS trust mode settings for all CoS-configurable interfaces or configure CoS settings per interface.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure CoS Interface Settings for an Interface You can configure the trust mode for one or more interfaces and apply an interface shaping rate to all interfaces or to a specific interface. To configure CoS settings for an interface: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • To configure all interfaces with the same settings, select the check box in the heading row. 8. From the Interface Trust Mode menu, select one of the following trust mode options for ingress traffic on the selected interfaces: • Untrusted. Do not trust any CoS packet marking at ingress. • 802.1p. The eight priority tags that are specified in IEEE 802.1p are p0 to p7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select QoS > CoS > Advanced > Interface Queue Configuration. 6. To display information for all ports and LAGs, click the All link. 7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Map 802.1p Priorities to Queues You can view or change which internal traffic classes are mapped to the 802.1p priority class values in Ethernet frames that the device receives. The priority-to-traffic class mappings can be applied globally or per interface.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The values in the menu under each priority represent the traffic class. The traffic class is the hardware queue for a port. Higher traffic class values indicate a higher queue position. Before traffic in a lower queue is sent, it must wait for traffic in higher queues to be sent. 8. Click the Apply button. Your settings are saved. Map DSCP Values to Queues You can map an internal traffic class to a DSCP value.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The traffic class is the hardware queue for a port. Higher traffic class values indicate a higher queue position. Before traffic in a lower queue is sent, it must wait for traffic in higher queues to be sent. The allowed Per Hop Behavior (PHBs) values, apart from other DSCP experimental values, are as follows: • Class Selector (CS) PHB. These values are based on IP precedence. • Assured Forwarding (AF) PHB.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure DiffServ Settings Packets are filtered and processed based on defined criteria. The filtering criteria is defined by a class. The processing is defined by a policy's attributes. Policy attributes can be defined on a per-class instance basis, and it is these attributes that are applied when a match occurs. The configuration process begins with defining one or more match criteria for a class.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. Select the administrative mode for DiffServ: • Enable. Differentiated services are active. This is the default setting. • Disable. The DiffServ configuration is retained and can be changed but is not active. 7. Click the Apply button. Your settings are saved. The following table describes the information displayed in the Status table on the DiffServ Configuration page. Table 60.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Create and Configure a DiffServ Class To create and configure a DiffServ class: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 10. Define the criteria that must be associated the DiffServ class: • Match Every. Select this radio button to add a match condition that considers all packets to belong to the class. The only selection from the Match Every menu is Any. • Reference Class. Select this radio button to reference another class for criteria.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • • Source MAC. Select this radio button to require a packet’s source MAC address to match the specified MAC address. After you select this radio button, use the following fields to configure the source MAC address match criteria: - Address. The source MAC address to match. The source MAC address is specified as six two-digit hexadecimal numbers separated by colons. - Mask.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Destination L4 Port. Select this radio button to require a packet’s TCP/UDP destination port to match the specified protocol, which you must select from the menu. The range is 0 to 65535. The menu includes Other as an option for unnamed ports. • IP DSCP. Select this radio button to require the packet’s IP DiffServ Code Point (DSCP) value to match the specified IP DSCP keyword code, which you must select from the menu.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select QoS > DiffServ > Advanced > Class Configuration. The Class Name page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Delete a DiffServ Class To delete a DiffServ class: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports IPv6 ACL/DiffServ assignment is appropriate for LAG interfaces. The procedures described by an ACL or DiffServ policy are equally applicable on a LAG interface. Create and Configure an IPv6 DiffServ Class To create and configure an IPv6 DiffServ class: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The class name is a hyperlink to the page on which you can define the class configuration. 10. Define the criteria that must be associated the IPv6 DiffServ class: • Match Every. Select this radio button to add a match condition that considers all packets to belong to the class. The only selection from the Match Every menu is Any. • Reference Class. Select this radio button to reference another class for criteria.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports hexadecimal range from 0 to FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF and the prefix length can be in the range from 0 to 128. • Destination L4 Port. Select this radio button to require a packet’s TCP/UDP destination port to match the specified protocol, which you must select from the menu. The range is 0 to 65535. The menu includes Other as an option for unnamed ports. • Flow Label.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select QoS > DiffServ > Advanced > IPv6 Class Configuration. The Class Name page displays. 6. Select the check box next to the class name. 7. In the Class Name field, specify the new name. 8. Click the Apply button. Your settings are saved. Change the Criteria for an Existing IPv6 DiffServ Class To change the criteria for an existing IPv6 DiffServ class: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. Enter a policy name in the Policy Name field. You cannot specify the policy type. By default, the policy type is In, indicating that the policy applies to ingress packets. 7. From the Member Class menu, optionally select an existing class that you want to associate with the new policy. 8. Click the Add button. The new policy is added. 9. After creating the policy, click the policy name.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 11. Configure the policy attributes: • Drop. Select this radio button to require each inbound packet to be dropped. • Mark VLAN CoS. Select this radio button to specify the VLAN priority, which you must select from the menu. The VLAN priority is expressed as an integer value in the range from 0 to 7. • Mark IP Precedence.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports In both the Conform Action section and the Violate Action section, select one of the following actions: • Send. Packets are forwarded unmodified. This is the default confirming action and the default violating action. • Drop. Packets are dropped. • Mark CoS. Packets are marked by DiffServ with the specified CoS value before being forwarded. This selection requires that the Mark CoS field is set.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select QoS > DiffServ > Advanced > Policy Configuration. The Policy Configuration page displays. 6. Select the check box next to the policy name. 7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Remove a Class From an Existing DiffServ Policy To remove a class from an existing DiffServ policy: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select QoS > DiffServ > Advanced > Policy Configuration. The Policy Configuration page displays. 6. Select the check box next to the policy name. 7. Click the Delete button. The policy is removed. Configure the DiffServ Service Interface You can activate a policy on an interface. Attach a DiffServ Policy to an Interface To attach a DiffServ policy to an interface: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • To configure multiple interfaces with the same settings, select the check box associated with each interface. • To configure all interfaces with the same settings, select the check box in the heading row. 8. From the Policy Name menu, select a policy name. 9. Click the Apply button. Your settings are saved. The following table describes the nonconfigurable information displayed on the page. Table 64.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Remove a DiffServ Policy From an Interface To remove a DiffServ policy from an interface: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select QoS > DiffServ > Advanced > Service Statistics. 6. To refresh the page with the latest information about the switch, click the Refresh button.
6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Management Security Settings You can configure the login password, Remote Authorization Dial-In User Service (RADIUS) settings, Terminal Access Controller Access Control System (TACACS) settings, and authentication lists. Change the Password You can change the login password. To change the login password for the management interface: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Reset the Password to the Default Password You can reset the password to the default password, which is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports RADIUS Overview RADIUS servers provide additional security for networks. The RADIUS server maintains a user database, which contains per-user authentication information. The switch passes information to the configured RADIUS server, which can authenticate a user name and password before authorizing use of the network.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports is the server configured as the primary server. If no servers are configured as the primary server, the current server is the most recently added RADIUS server. 6. In the Max Number of Retransmits field, specify the maximum number of times a request packet is retransmitted to the RADIUS server. The valid range is from 1 to 15. The default value is 4.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure a RADIUS Authentication Server on the Switch Use the RADIUS Server Configuration page to view and configure various settings for a RADIUS server configured on the switch. Add a Primary RADIUS Authentication Server to the Switch To add a primary RADIUS authentication server to the switch and view the RADIUS authentication server statistics: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The message authenticator adds protection to RADIUS messages by using an MD5 hash to encrypt each message. The shared secret is used as the key, and if the message fails to be verified by the RADIUS server, it is discarded. 12. Click the Add button. The server is added to the switch. 13. Click the Apply button. Your settings are saved. 14.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 67. RADIUS authentication server statistics information (continued) Field Description Unknown Types The number of RADIUS packets of unknown type that were received from this server on the authentication port. Packets Dropped The number of RADIUS packets received from this server on the authentication port and dropped for some other reason.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The Accounting Server Configuration page displays. 6. In the Accounting Server Address field, specify the IP address of the RADIUS accounting server to add. 7. In the Port field, specify the UDP port number the server uses to verify the RADIUS accounting server authentication. The default UDP port number is 1813. 8. From the Secret Configured menu, select Yes to add a RADIUS secret in the next field.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 68. RADIUS accounting server statistics information (continued) Field Description Timeouts The number of accounting time-outs to this server. Unknown Types The number of RADIUS packets of unknown type that were received from this server on the accounting port. Packets Dropped The number of RADIUS packets that were received from this server on the accounting port and dropped for some other reason.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Modify the Settings for a RADIUS Accounting Server on the Switch To modify the settings for a RADIUS accounting server on the switch: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select Security > Management Security > RADIUS > Accounting Server Configuration. The Accounting Server Configuration page displays. 6. Select the check box next to the IP address of the server to remove. 7. Click the Delete button. The RADIUS accounting server is removed. 8. Click the Apply button. Your settings are saved.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The TACACS+ Configuration page displays. 6. In the Key String field, specify the authentication and encryption key for TACACS+ communications between the switch and the TACACS+ server. The valid range is 0–128. The key must match the key configured on the TACACS+ server. 7. In the Connection Timeout field, specify the maximum number of seconds allowed to establish a TCP connection between the switch and the TACACS+ server.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 9. In the Key String field, specify the authentication and encryption key for TACACS+ communications between the device and the TACACS+ server. The valid range is 0–128. The key must match the key used on the TACACS+ server. 10. In the Connection Timeout field, specify the time that passes before the connection between the device and the TACACS+ server times out. The range is 1–30.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. From the menu in the 1 column, select the authentication method that must be used first in the selected authentication login list. If you select a method that does not time out as the first method, such as Local, no other method is tried, even if you specified more than one method. User authentication occurs in the order the methods are selected. Possible methods are as follows: • Local.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Security > Management Security > Authentication List > HTTPS Authentication List.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure the Dot1x Authentication List The Dot1x authentication list defines the IEEE 802.1X authentication method used for the default list. The default list is dot1xList. To configure the dot1x authentication list: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure Management Access You can configure HTTP and secure HTTP access to the switch management interface. You can also configure access control profiles and access rules. Configure HTTP Settings You can configure the settings for HTTP access to the switch. To configure the HTTP server settings: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports HTTPS Configuration Secure HTTP enables the transmission of HTTP over an encrypted Secure Sockets Layer (SSL) or Transport Layer Security (TLS) connection. When you manage the switch by using a web interface, Secure HTTP can help ensure that communication between the management system and the switch is protected from eavesdroppers and man-in-the-middle attacks. You can configure the settings for HTTPS access to the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 10. In the HTTPS Session Soft Timeout (Minutes) field, enter the inactivity time-out for HTTPS sessions. The value must be in the range of 1 to 60 minutes. The default value is 5 minutes. The configured value is displayed. After the session is inactive for the configured time, you are automatically logged out and must reenter the password to access the management interface.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The Certificate Present field displays whether a certificate is present on the switch. 6. In the Certificate Management area, select Generate Certificates. 7. Click the Apply button. The switch generates an SSL certificate. The Certificate Generation Status field shows information about the progress. Delete an SSL Certificate To delete an SSL certificate: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • The switch contains a path to the TFTP server. To configure the certificate download settings for HTTPS sessions: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 11. Select the Start File Transfer check box. 12. Click the Apply button. The file transfer starts. A status message displays during the transfer and upon successful completion of the transfer. Access Control Access control allows you to configure a profile and set access rules. Configure an Access Control Profile You can set up a security access profile. To configure an access profile: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 9. To refresh the page with the latest information about the switch, click the Refresh button. The following table describes the nonconfigurable data that is displayed. Table 69. Access profile configuration profile summary Field Description Rule Type The action performed when the rules match. Service Type The selected service type. The policy is restricted by the selected service type chosen.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The Access Rule Configuration page displays. 6. From the Rule Type menu, select Permit or Deny to permit or deny access when the selected rules are matched. A Permit rule allows access by traffic that matches the rule criteria. A Deny rule blocks traffic that matches the rule criteria. 7. From the Service Type menu, select the access method to which the rule is applied. The policy is restricted by the selected access method.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure Global 802.1X Settings You can configure global port access control settings on the switch. To globally enable all 802.1X features: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If RADIUS-assigned VLANs are enabled, the RADIUS server is includes the VLAN ID in the 802.1X tunnel attributes of its response message to the device. If dynamic VLAN creation is enabled on the device and the RADIUS-assigned VLAN does not exist, then the assigned VLAN is dynamically created. This implies that the client can connect from any port and can get assigned to the appropriate VLAN.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 8. Specify the following settings: • Port Control. Defines the port authorization state. The control mode is set only if the link status of the port is link up. Select one of the following options: - Auto. The switch automatically detects the mode of the interface. - Authorized. The switch places the interface into an authorized state without being authenticated.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Supplicant Timeout. Specify the supplicant time-out for the selected port. The supplicant time-out is the value, in seconds, after which the supplicant times out. • Server Timeout. Specify the time that elapses before the switch resends a request to the authentication server. 9. Click the Apply button. Your settings are saved.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Initialize 802.1X on a Port To initialize 802.1X on a port: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 5. Select Security > Port Authentication > Advanced > Port Authentication. The Port Authentication page displays. 6. Select the check box associated with the port to reauthenticate. 7. Click the Reauthenticate button. The selected port is forced to restart the authentication process.This button is available only if the control mode is auto.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the fields on the Port Summary page. Table 71. Port summary Field Description Port The port for which the settings are displayed in the current table row. Control Mode Indicates the configured control mode for the port. Possible values are as follows: • Auto.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Security > Port Authentication > Advanced > Client Summary.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Set Up Traffic Control You can configure MAC filters, storm control, port security, protected port, and private VLAN settings. Manage MAC Filtering You can create MAC filters that limit the traffic allowed into and out of specified ports on the switch. Create a MAC Filter To create a MAC filter: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 9. In the Port and LAG tables in the Source Port Members section, select the ports and LAGs that must be included in the inbound filter. If a packet with the MAC address and VLAN ID that you specify is received on a port that is not part of the inbound filter, the packet is dropped. 10. In the Port and LAG tables in the Destination Port Members section, select the ports and LAGs that must be included in the outbound filter.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View the MAC Filter Summary You can view the MAC filters that are configured on the switch. To view the MAC filter summary: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure storm control settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Your settings are saved. 11. To enable or disable storm control for one or more ports or to specify different threshold and control action settings for one or more ports, do the following: a.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure port security settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View Learned MAC Addresses and Convert Them to Static MAC Addresses You can convert a dynamically learned MAC address to a statically locked address. To view learned MAC addresses for an individual interface or LAG and convert these MAC addresses to static MAC addresses: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 11. To convert the dynamically learned MAC address to a statically locked addresses, select the Convert Dynamic Address to Static check box. 12. Click the Apply button. The dynamic MAC address entries are converted to static MAC address entries in a numerically ascending order until the static limit is reached.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure a Private VLAN A private VLAN contains switch ports that cannot communicate with each other, but can access another network. These ports are called private ports. Each private VLAN contains one or more private ports and a single uplink port or uplink aggregation group. Note that all traffic between private ports is blocked at all layers, not just Layer 2 traffic, but also traffic such as FTP, HTTP, and Telnet.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure Private VLAN Association Settings To configure private VLAN association: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Security > Traffic Control > Private VLAN > Private Vlan Host Interface Configuration.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Security > Traffic Control > Private VLAN > Private Vlan Promiscuous Interface Configuration. The Private VLAN Promiscuous Interface Configuration page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure an ACL: 1. Create an IPv4-based or IPv6-based or MAC-based ACL ID. 2. Create a rule and assign it to a unique ACL ID. 3. Define the rules, which can identify protocols, source, and destination IP and MAC addresses, and other packet-matching criteria. 4. Use the ID number to assign the ACL to a port or to a LAG. To view ACL configuration examples, see Access Control Lists (ACLs) on page 392.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. From the ACL Type menu, select the type of ACL. You can select from the following ACL types: • ACL Based on Destination MAC. Creates an ACL based on the destination MAC address, destination MAC mask, and VLAN. • ACL Based on Source MAC. Creates an ACL based on the source MAC address, source MAC mask, and VLAN. • ACL Based on Destination IPv4. Creates an ACL based on the destination IPv4 address and IPv4 address mask.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Note: For L4 port options, two rules are created (one for TCP and one for UDP). 7. In the Sequence Number field, enter a whole number in the range of 1 to 2147483647 that is used to identify the rule. 8. From the Action menu, select Permit or Deny to specify the action that must be taken if a packet matches the rule’s criteria.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports ACL Based On Fields Destination IPv4 L4 Port • • Destination L4 port (protocol). Specify the destination IPv4 L4 port protocol. Destination L4 port (value). Specify the destination IPv4 L4 port value. Source IPv4 L4 Port • • Source L4 port (protocol). Specify the source IPv4 L4 port protocol. Source L4 port (value). Specify the source IPv4 L4 port value. Destination IPv6 L4 Port • • Destination L4 port (protocol).
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Modify an ACL Rule To modify an ACL rule: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select Security > ACL > ACL Wizard. The ACL Wizard page displays. 6. Select check box that is associated with the rule. 7. Click the Delete button. The rule is removed. ACL Wizard Example In the following figure, the ACL rule is configured to check for packet matches on ports 4, 5, and 9 and on LAG 1. Only the Inbound option is valid. Packets that include a source address in the 192.168.3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Multiple steps are involved in defining a MAC ACL and applying it to the switch: 1. Create the ACL ID. 2. Create a MAC rule. 3. Associate the MAC ACL with one or more interfaces. You can view or delete MAC ACL configurations in the MAC Binding table (see View or Delete MAC ACL Bindings in the MAC Binding Table on page 300. Add a MAC ACL To add a MAC ACL: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Change the Name of a MAC ACL To change the name of a MAC ACL: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select Security > ACL > Basic > MAC ACL. The MAC ACL page displays. 6. Select check box that is associated with the rule. 7. Click the Delete button. The rule is removed. Configure MAC ACL Rules You can define rules for MAC-based ACLs. The access list definition includes rules that specify whether traffic matching the criteria is forwarded normally or discarded. A default deny all rule is the last rule of every list.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. In the Sequence Number field, enter a whole number in the range of 1 to 2147483647 to identify the rule. 8. From the Action menu, select the action that must be taken if a packet matches the rule’s criteria: • Permit. Forwards packets that meet the ACL criteria. • Deny. Drops packets that meet the ACL criteria. 9.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 16. From the EtherType Key menu, select the EtherType value that must be compared against the information in an Ethernet frame. The valid values are as follows: • Appletalk • ARP • IBM SNA • IPv4 • IPv6 • IPX • MPLS multicast • MPLS unicast • NetBios • Novell • PPPoE • RARP • User Value 17.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports When set to Enable, logging is enabled for this ACL rule (subject to resource availability on the switch). If the access list trap flag is also enabled, periodic traps are generated, indicating the number of times the rule was evoked during the report interval. A fixed five-minute report interval is used for the switch. A trap is not issued if the ACL rule hit count is zero for the interval.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. From the ACL ID menu, select an ACL. The fixed selection from the Direction menu is Inbound, which means that MAC ACL rules are applied to traffic entering the interface. 7. In the Sequence Number field, optionally specify a number to indicate the order of the access list relative to other access lists already assigned to the interface and direction. A low number indicates high precedence order.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the information displayed in the Interface Binding Status table. Table 76. Interface Binding Status table Field Description Interface The interface of the ACL assigned. Direction The selected packet filtering direction for the ACL. ACL Type The type of ACL assigned to the selected interface and direction.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the information that is displayed in the MAC Binding Table. Table 77. MAC Binding Table Field Description Interface The interface of the ACL assigned. Direction The selected packet filtering direction for the ACL. ACL Type The type of ACL assigned to the selected interface and direction. ACL ID The ACL name identifying the ACL assigned to the selected interface and direction.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The Current Number of ACL field displays the current number of all ACLs configured on the switch. The Maximum ACL field displays the maximum number of IP ACLs that can be configured on the switch. 6. In the IP ACL ID field, specify the ACL ID or IP ACL name, which depends on the IP ACL type. The IP ACL ID is an integer in the following range: • 1–99.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. Select the check box that is associated with the IP ACL. 7. Click the Delete button. The IP ACL is removed. Configure Rules for a Basic IP ACL You can define rules for IP-based standard ACLs (basic ACLs). The access list definition includes rules that specify whether traffic matching the criteria is forwarded normally or discarded. Note: An implicit deny all rule is included at the end of an ACL list.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If no rules exist, the Basic ACL Rule Table shows the message No rules have been configured for this ACL. If one or more rules exist for the ACL, the rules display in the Basic ACL Rule Table. 6. From the ACL ID menu, select the IP ACL for which you want to add a rule. For basic IP ACLs, this must be an ID in the range from 1 to 99. 7. Click the Add button. 8.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Mirror Interface. From the Mirror Interface menu, select the specific egress interface to which the matching traffic stream must be copied, in addition to being forwarded normally by the switch. This field cannot be set if a redirect interface is already configured for the IP ACL rule. This field is visible for a Permit action. • Redirect Interface.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 6. From the ACL ID menu, select the ACL that includes the rule that you want to modify. 7. In the Basic ACL Rule Table, click the rule. The rule is a hyperlink. The Standard ACL Rule Configuration page displays. 8. Modify the basic IP ACL rule criteria. 9. Click the Apply button. Your settings are saved. Delete a Basic IP ACL RUle To delete a basic IP ACL rule: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Add a Rule for an Extended IP ACL To add a rule for an extended IP ACL: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The previous figure does not show the rightmost fields. 8. Configure the following match criteria for the rule: • Sequence Number. Enter a whole number in the range of 1 to 2147483647 that is used to identify the rule. An extended IP ACL can contain up to 50 rules. • Action. Select the ACL forwarding action, which is one of the following: - Permit. Forward packets that meet the ACL criteria. - Deny.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • • Interface. For a Permit action, use either a mirror interface or a redirect interface: - Select the Mirror Interface radio button and use the menu to specify the egress interface to which the matching traffic stream is copied, in addition to being forwarded normally by the device.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The relevant matching conditions for L4 port numbers are as follows: - • Equal. IP ACL rule matches only if the Layer 4 source port number is equal to the specified port number or port protocol. • Not Equal. IP ACL rule matches only if the Layer 4 source port number is not equal to the specified port number or port protocol. • Less Than.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Dst L4. The options are available only when the protocol is set to TCP or UDP. Use the destination L4 port option to specify relevant matching conditions for L4 port numbers in the extended ACL rule. You can select either the Port radio button or the Range radio button: - Port radio button.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The wildcard mask determines which bits are used and which bits are ignored. A wildcard mask of 0.0.0.0 indicates that none of the bits are important. A wildcard of 255.255.255.255 indicates that all of the bits are important. • IGMP Type. If you specify the IGMP type, the IP ACL rule matches the specified IGMP message type. Possible values are in the range 0 to 255. If this field is left empty, it means any. • ICMP.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports - IP TOS. This is an optional configuration. The IP ToS field in a packet is defined as all 8 bits of the service type octet in the IP header. The ToS bits value is a hexadecimal number that is composed of numbers 00 to 09 and AA to FF. The ToS mask value is a hexadecimal number that is composed of numbers 00 to FF.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Delete an Extended IP ACL Rule To delete an extended IP ACL rule: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Security > ACL > Advanced > IPv6 ACL. The IPV6 Configuration page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select Security > ACL > Advanced > IPv6 ACL. The IPv6 Configuration page displays. 6. Select the check box that is associated with the IPv6 ACL. 7. Click the Delete button. The IPv6 ACL is removed. Configure Rules for an IPv6 ACL You can define rules for IPv6 ACLs. The access list definition includes rules that specify whether traffic matching the criteria is forwarded normally or discarded.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The previous figure does not show all columns. If no rules exists, the IPv6 ACL Rule Table shows the message No rules have been configured for this ACL. If one or more rules exist for the ACL, the rules display in the IPv6 ACL Rule Table. 6. From the ACL Name menu, select the IPv6 ACL for which you want to add a rule. 7. Click the Add button. The previous figure does not show the rightmost fields. 8.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Action. Select the ACL forwarding action by selecting one of the following radio buttons: - Permit. Forward packets that meet the ACL criteria. - Deny. Drop packets that meet the ACL criteria. • Egress Queue. If you select the Permit radio button, select the hardware egress queue identifier that is used to handle all packets matching this IPv6 ACL rule. The range of queue IDs is 0 to 7. • Logging.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Src L4. The options are available only when the protocol is set to TCP or UDP. Use the source L4 port option to specify relevant matching conditions for L4 port numbers in the extended ACL rule. You can select either the Port radio button or the Range radio button: - Port radio button.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Dst. In the Dst field, enter a destination IPv6 address to be compared to a packet’s destination IPv6 address as a match criterion for the selected IPv6 ACL rule: - If you select the IPv6 Address radio button, enter an IPv6 address to apply this criteria. If this field is left empty, it means any. - If you select the Host radio button, enter a host source IPv6 address to match the specified IPv6 address.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports You can either enter the port range yourself or select one of the following protocols from the menu: • The destination IP TCP port protocols are domain, echo, ftp, ftpdata, www-http, smtp, telnet, pop2, pop3, and bgp. • The destination IP UDP port protocols are domain, echo, snmp, ntp, rip, time, who, and tftp.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports that is used by end stations to signify Quality of Service handling in routers. The flow label can specified within the range 0 to 1048575. • IPv6 DSCP Service. Specify the IP DiffServ Code Point (DSCP) field. This is an optional configuration. The DSCP is defined as the high-order 6 bits of the service type octet in the IPv6 header. Enter an integer from 0 to 63. To select the IPv6 DSCP, select one of the DSCP keywords.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Delete an IPv6 ACL Rule To delete an IPv6 ACL rule: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Security > ACL > Advanced > IP Binding Configuration. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The Ports and LAG tables display the available and valid interfaces for ACL binding. All nonrouting physical interfaces, VLAN interfaces, and interfaces participating in LAGs are listed. 9. Click the Apply button. Your settings are saved. The following table describes the nonconfigurable information displayed on the page. Table 79. IP Binding Status table Field Description Interface The selected interface.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports a. Select the check box next to the interface. b. Click the Delete button. The binding is removed. The following table describes the information displayed in the IP ACL Binding Table. Table 80. IP ACL Binding Table Field Description Interface The interface. Direction The selected packet filtering direction for the ACL. ACL Type The type of ACL assigned to the selected interface and direction.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. From the Direction menu, select the packet filtering direction. 8. In the Sequence Number field, enter an optional sequence number. You can specify an optional sequence number to indicate the order of this access list relative to other access lists that are already assigned to the VLAN ID and selected direction. A lower number indicates a higher precedence order.
7.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Reboot the Switch You can reboot the switch from the local browser interface. Note: The switch provides a recessed multi-function Reset button on the back panel that lets you reboot (power-cycle) the switch. To reboot the switch, press the Reset button for about two seconds. (Do not press the button for more than five seconds!) The switch restarts but retains its custom settings. To reboot the switch: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports password. The default management mode is reset to NETGEAR Insight Mobile App and Insight Cloud Portal. For information about reconnecting to the switch, see Access the Switch on page 13. For information about changing the management mode, see Change the Management Mode of the Switch on page 20.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Export a File From the Switch You can export configuration (ASCII or log ASCII) files from the switch to a file server by using TFTP or HTTP.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Tech Support. The tech support file is a text-base file that contains a variety of hardware, software, and configuration information that can assist in device and network troubleshooting. • Crash Logs. Specify the crash logs to retrieve them. 7. From the Server Address Type menu, select the format for the Server Address field: • IPv4. Indicates that the TFTP server address is an IP address in dotted-decimal format.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Maintenance > Export > HTTP File Export. The HTTP File Export page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • • The file is in the correct format. The switch contains a path to the TFTP server. You can also download files by using HTTP. See Download a File to the Switch Using HTTP on page 335 for additional information. To download a file to the switch from a TFTP server: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. If the selection from the File Type menu is Software, the Image Name menu is displayed and you must select the software image that must be downloaded to the switch: • image1. Select image1 to upload image1. • image2. Select image2 to upload image2. Note: We recommended that you do not overwrite the active image. If you do so, the switch displays a warning that you are trying to overwrite the active image. 8.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The file name can contain up to 80 characters. 9. Click the Apply button. The file transfer begins. The page displays information about the progress of the file transfer. The page refreshes automatically when the file transfer completes (or if it fails). Note: After a file transfer is started, wait until the page refreshes.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The System Information page displays. 5. Select Maintenance > File Management > Dual Image > Dual Image Configuration. The Dual Image Configuration page displays. 6. From the Image Name menu, select the image that is not the image displayed in the Current-active field. The Current-active field displays the name of the active image. 7. To specify a name for the selected image, enter one in the Image Description field. 8.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. Select the Delete Image check box. 8. Click the Apply button. The image is removed. View the Dual Image Status You can view information about the active and backup images on the switch. To view dual image status information: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Perform Troubleshooting Tasks You can send a ping or a traceroute.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The Ping Details page displays. 6. In the IP Address/Host Name field, enter the IP address or host name of the device that must be pinged. 7. In the Count field, enter the number of echo requests that must be sent. The default value is 3. The range is 1 to 15. 8. In the Interval field, enter the time between ping packets in seconds. The default value is 3 seconds. The range is 1 to 60. 9.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Maintenance > Troubleshooting > Ping IPv6. The Ping IPv6 page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Send an IPv4 Traceroute You can configure the switch to send a traceroute request to a specified IP address or host name. You can use this to discover the paths that packets take to a remote destination. Once you click the Apply button, the switch sends a traceroute and the results are displayed below the configurable data. If a reply to the traceroute is received, the following message displays: 1 e.f.g.h 2 0.0.0.0 3 0.0.0.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 11. In the Interval field, enter the time between probes in seconds. The default value is 3. The range is 1 to 60. 12. In the Port field, enter the UDP destination port for the probe packets. The default value is 33434. The range is 1–65535. 13. In the Size field, enter the size of the probe packets. The default value is 0. The range is 0 to 39936. 14.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Maintenance > Troubleshooting > Traceroute IPv6. The Traceroute IPv6 page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Enable Remote Diagnostics You can enable or disable the option to access the switch remotely. When remote access is enabled, you can perform diagnostics services. To enable remote diagnostics: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired connection to connect your computer to the network, or connect directly to a switch that is off-network using an Ethernet cable. 2.
8. Manage Power over Ethernet This chapter covers the following topics: • PoE Overview • Device Class Power Requirements • Power Allocation and Power Budget • Configure the Global PoE Settings • Manage and View the PoE Port Configuration • Reset One or More PoE or PoE+ Ports • Set Up PoE Timer Schedules Note: This chapter applies to models GC110P, GC510P, and GC510PP. Model GC110 does not support Power over Ethernet.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports PoE Overview Depending on the model, the switch includes eight Power over Ethernet plus (PoE) or PoE plus (PoE+) ports. The following table shows the capacity for each model. Table 82. PoE capacities for each model Model Maximum PoE Power Per Port Maximum Power Budget Across All Active PoE Ports GC110 PoE is not supported PoE is not supported GC110P 15.4W PoE (IEEE 802.3af) 62W GC510P 30W PoE+ (IEEE 802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table shows the device classes for PoE+ devices adhering to the IEEE 802.3at standard. The device classes for PoE devices adhering to the IEEE 802.3af standard are identical with the exception that Device Class 4 is not supported. Table 83.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To determine the delivered power by PoE or PoE+ ports: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select System > PoE > Basic > PoE Configuration. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Manage and View the PoE Port Configuration Depending on the model, the switch includes eight PoE or PoE+ ports. To configure and view the PoE or PoE+ port settings: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The settings that you configure apply to all selected PoE or PoE+ ports. Menu Item Description Port Power Select the administrative mode of the port: • Enable. The port’s capacity to deliver power is enabled. This is the default setting. • Disable. The port’s capacity to deliver power is disabled.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Menu Item Description Detection Type The detection type specifies how the port detects the attached PD. Select one of the following types: • IEEE 802. The port performs a 4-point resistive detection. This is the default setting. • 4pt 802.3af + Legacy. The port performs a 4-point resistive detection, and if required, continues with legacy detection. • Legacy. The port performs legacy detection.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Field Description Fault Status The error description when the PoE port is in a fault state. The possible values are as follows: • No Error. The port is not in any error state and can provide power. • MPS Absent. The port detected the absence of the main power supply, preventing the port from providing power. • Short. The port detected a short circuit condition, preventing the port from providing power. • Overload.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Set Up PoE Timer Schedules The switch lets you define multiple timer schedules that you can use for PoE power delivery to attached PDs. After you create a timer schedule, you can associate it with one or more PoE ports (see Manage and View the PoE Port Configuration on page 353). You can use a separate timer schedule for each PoE port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Specify the Settings for an Absolute PoE Timer Schedule An absolute timer schedule applies to specific dates and times. The schedule is executed once only. To specify the settings for a PoE timer schedule that uses specific dates and times: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports d. Next to the Date End field, click the calendar icon and use the menus in the pop-up window to enter the date in the DD-Mon-YYYY format to specify when the timer schedule must stop. 8. Click the Add button. The entry for the timer schedule is added.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Selecting an existing entry lets you make changes to that entry. 7. In the Timer Schedule Configuration section, specify the recurrence pattern: a. In the Time Start field, enter the time of day in the HH:MM format to specify when the timer schedule must start. b. In the Time End field, enter the time of day in the HH:MM format to specify when the timer schedule must stop. c.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. Select System > Timer Schedule > Advanced > Timer Schedule Configuration. The Timer Schedule Configuration page displays. 6. From the Timer Schedule Name menu, select the schedule name. 7. From the Timer Schedule Type menu, select the schedule type. 8. From the Timer Schedule Entry menu, select the schedule entry. 9. Click the Delete button. The entry is deleted.
9. 9 Monitor the System This chapter contains the following sections.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Monitor the Switch and the Ports The following sections describe how you can view a variety of information about the amount and type of traffic that is transmitted from and received on the switch: • View or Clear the Switch Statistics on page 364 • View or Clear Port Statistics on page 366 • View or Clear Detailed Port Statistics on page 368 • View or Clear EAP Statistics on page 374 • Perform a Cable Test on page 37
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the switch statistics displayed on the page. Table 85. Switch statistics Field Description ifIndex The interface index of the interface table entry associated with the processor of this switch. Octets Received The total number of octets of data received by the processor (excluding framing bits, but including FCS octets).
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 85. Switch statistics (continued) Field Description Static VLAN Entries The number of active VLAN entries that were created statically on the switch. VLAN Deletes The number of VLANs that were created and then deleted on the switch since the last reboot. Time Since Counters Last Cleared The elapsed time, in days, hours, minutes, and seconds, since the statistics for the switch were last cleared.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the per-port statistics displayed on the page. Table 86. Port statistics Field Description Interface The interface for which the statistics are displayed. Total Packets Received Without Errors The total number of packets received that were without errors.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 7. Click the Clear button. All counters are reset to 0. Reset Counters for a Specific Interface To reset the counters for a specific interface: 1. Connect your computer to the same network as the switch. You can use a WiFi or wired network connection, or connect directly to a switch that is off-network using an Ethernet cable. 2. Launch a web browser. 3.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 87. Detailed port statistics (continued) Field Description STP State The port's current Spanning Tree state. This state controls what action a port takes on receipt of a frame. If the bridge detects a malfunctioning port, it places that port into the broken state. The states are defined in IEEE 802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 87. Detailed port statistics (continued) Field Description Packets RX and TX 512-1023 The total number of packets (including bad packets) received and transmitted Octets that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 87. Detailed port statistics (continued) Field Description Unicast Packets Received The number of subnetwork-unicast packets delivered to a higher-layer protocol. Multicast Packets Received The total number of well-formed packets received that were directed to a multicast address. This number does not include packets directed to the broadcast address.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 87. Detailed port statistics (continued) Field Description Total Packets Transmitted (Octets) The total number of octets of data (including those in bad packets) transmitted on the network (excluding framing bits but including FCS octets). This object can be used as a reasonable estimate of Ethernet utilization.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 87. Detailed port statistics (continued) Field Description Total Transmit Errors The sum of single, multiple, and excessive collisions. Total Transmit Packets Discarded The sum of single collision frames discarded, multiple collision frames discarded, and excessive frames discarded. Single Collision Frames The number of successfully transmitted frames for which transmission was inhibited by exactly one collision.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 88. EAP statistics Field Description EAP Request/ID Frames Transmitted The number of transmitted EAP request/identity frames. EAP Request Frames Transmitted The number of transmitted EAP request frames (other than request/identity frames). Perform a Cable Test You can test and view information about the cables that are connected to switch ports. To perform a cable test: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The following table describes the nonconfigurable information displayed on the page. Table 89. Cable Test information Field Description Cable Status Indicates the cable status: • Normal. The cable is working correctly. • Open. The cable is disconnected or a faulty connector exists. • Short. An electrical short exists in the cable. • Cable Test Failed. The cable status could not be determined.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports console log. Messages logged to a collector or relay through syslog support the same format as well. The following example shows the standard format for a log message: <14>2017-09-02 16:35:40 10.131.12.183-1 UNKN[2176789276]: main_login.c(179) 3855 %% HTTP Session 19 initiated for user admin connected from 10.27.64.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports message logged. Messages logged to a collector or relay through syslog use a format identical to the previous message. Manage the Flash Log The flash log is a persistent log, that is, is a log that is stored in persistent storage. Persistent storage survives across platform reboots. The first log type is the system startup log. The system startup log stores the first 32 messages received after system reboot.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports - Critical (2). The third-highest warning level. A critical log message is saved if a critical device malfunction occurs, for example, two device ports are not functioning, while the rest of the device ports remain functional. - Error (3). A device error occurred, such as a port being offline. - Warning (4). The lowest level of a device warning. - Notice (5). Normal but significant conditions.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The login window opens. 4. Enter the switch’s password in the password field. The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Monitoring > Logs > Server Log. The Server Log page displays. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The default password is password. If you added the switch to a network on the Insight app before and you did not yet change the password through the local browser interface, enter your Insight network password. The System Information page displays. 5. Select Monitoring > Logs > Server Log. The Server Log Configuration page displays. 6. Specify the following settings: • IP Address Type.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 2. Launch a web browser. 3. In the address field of your web browser, enter the IP address of the switch. If you do not know the IP address of the switch, see Access the Switch on page 13. The login window opens. 4. Enter the switch’s password in the password field. The default password is password.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View or Clear the Trap Logs You can view information about the SNMP traps generated on the switch. The information can be retrieved as a file. You can also display information about the traps that were sent. View the trap logs or clear the counters: 1. Connect your computer to the same network as the switch.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports View or Clear the Event Log You can display the event log, which is used to hold error messages for catastrophic events. After the event is logged and the updated log is saved in flash memory, the switch is reset. The log can hold at least 2,000 entries and is erased when an attempt is made to add an entry after it is full. The event log is preserved across system resets. To view the event log or clear the log: 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Configure Port Mirroring Port mirroring selects the network traffic for analysis by a network analyzer. This is done for specific ports of the switch. As such, many switch ports are configured as source ports and one switch port is configured as a destination port. You can configure how traffic is mirrored on a source port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 8. Use one of the following methods to narrow down the ports that are displayed: • Select 1 to display the physical ports of the selected unit. • Select LAG to display a list of LAGs only. • Select CPU to display a list of CPUs only. • Select All to display a list of all physical ports, LAGs, CPUs, and VLANs. 9.
A. Configuration Examples This appendix contains information about how to configure the following features. The appendix covers the following topics: • Virtual Local Area Networks (VLANs) • Access Control Lists (ACLs) • Differentiated Services (DiffServ) • 802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Virtual Local Area Networks (VLANs) A local area network (LAN) can generally be defined as a broadcast domain. Hubs, bridges, or switches in the same physical segment or segments connect all end node devices. End nodes can communicate with each other without the need for a router. Routers connect LANs together, routing the traffic to the appropriate port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Packets leaving the switch are either tagged or untagged, depending on the setting for that port’s VLAN membership properties. A U for a given port means that packets leaving the switch from that port are untagged. Inversely, a T for a given port means that packets leaving the switch from that port are tagged with the VLAN ID that is associated with the port.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports untagged packet as it leaves port 6. For port 5, the outgoing packet leaves as a tagged packet with VLAN ID 20. Access Control Lists (ACLs) ACLs ensure that only authorized users can access specific resources while blocking off any unwarranted attempts to reach network resources.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Assign Queue ID. 0 • Match Every. False • CoS. 0 • Destination MAC. 01:02:1A:BC:DE:EF • Destination MAC Mask. 00:00:00:00:FF:FF • EtherType. User Value. • Source MAC. 02:02:1A:BC:DE:EF • Source MAC Mask. 00:00:00:00:FF:FF • VLAN ID. 2 3. On the MAC Binding Configuration page (see Configure MAC Bindings on page 298), assign the Sales_ACL to ports 6, 7, and 8, and then click the Apply button.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 4. On the IP Rules page (see Configure Rules for a Basic IP ACL on page 303), create a second rule for IP ACL 1 with the following settings: • Sequence Number. 2 • Action. Permit • Match Every. True 5. Click the Add button. 6. On the IP Binding Configuration page (see Configure IP ACL Interface Bindings on page 323), assign ACL ID 1 to the interface Gigabit ports 2, 3, and 4, and assign a sequence number of 1.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports The switch supports DiffServ. The DiffServ feature contains a number of conceptual QoS building blocks that you can use to construct a differentiated service network. Use these same blocks in different ways to build other types of QoS architectures.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports To configure DiffServ, you must define service levels, namely the forwarding classes/PHBs identified by a given DSCP value, on the egress interface. You define these service levels by configuring BA classes for each. Creating Policies Use DiffServ policies to associate a collection of classes that you configure with one or more QoS policy statements. The result of this association is referred to as a policy.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Policing with color mode awareness. Policing in the DiffServ feature uses either color blind or color aware mode. Color blind mode ignores the coloration (marking) of the incoming packet. Color aware mode takes into consideration the current packet marking when the switch determines the policing outcome. An auxiliary traffic class is used in conjunction with the policing definition to specify a value for one of the 802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports 5. On the Policy Configuration page (see Create and Configure a DiffServ Policy on page 228), create a new policy with the following settings: • Policy Selector. Policy1 • Member Class. Class1 6. Click the Add button. The policy is added. 7. Click the Policy1 hyperlink to view the Policy Class Configuration page for this policy. 8. Configure the Policy attributes as follows: • Assign Queue. 3 • Policy Attribute.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports LAN port with point-to-point connection characteristics. If the authentication and authorization process fails, access control prevents access to that port. In this context, a port is a single point of attachment to the LAN, such as a port of a MAC bridge and an association between stations or access points in IEEE 802.11 wireless LANs. The IEEE 802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports the information received from the supplicant to the authentication server for the credentials to be checked, which determines the authorization state of the port. The authenticator PAE controls the authorized/unauthorized state of the controlled port depending on the outcome of the RADIUS-based authentication process. Figure 1. 802.1X authentication roles 802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports This example uses the default values for the port authentication settings, but you can configure several additional settings. For example, the EAPOL Flood Mode field allows you to enable the forwarding of EAPoL frames when 802.1X is disabled on the device. 6.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports maximum possible extent. The connectivity calculated for the CIST provides the CST for interconnecting these regions, and an Internal Spanning Tree (IST) within each region.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports kind outside the region. In other words, connectivity within the region is independent of external connectivity. MSTP Example Configuration This example shows how to create an MSTP instance from the switch. The example network includes three different switches that serve different locations in the network. In this example, ports 1/0/1–1/0/5 are connected to host stations, so those links are not subject to network loops.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports • Switch 3. 20480 Note: Bridge priority values are multiples of 4096. If you do not specify a root bridge and all switches are assigned the same bridge priority value, the switch with the lowest MAC address is elected as the root bridge. 5. On the Port Configuration page (fro CST) for each switch, select ports 1/0/1–1/0/8 and select Enable from the STP Status menu (see Configure CST Port Settings on page 128). 6.
B.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Switch Specifications The switch conforms to the TCP/IP, UDP, HTTP, ICMP, TFTP, DHCP, IEEE 802.1D, IEEE 802.1p, and IEEE 802.1Q standards. Table 92.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 93. Feature Default Values and Default State (continued) Feature Name/Parameter Default VLAN Admin Mode Disabled Circuit ID Mode Disabled Interface Admin Mode Disabled 82 Option Trust Mode Disabled PoE Global System Usage Threshold 95% Power Management Mode Dynamic Traps Enabled Interface Admin Mode Enabled Port Priority Low Power Mode GC110P: 802.3af GC510P: 802.3at GC510PP: 802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 93. Feature Default Values and Default State (continued) Feature Name/Parameter Default Jumbo Frames Maximum Frame Size 1518 Flow Control Admin Mode Disabled 802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 93.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 93.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 93. Feature Default Values and Default State (continued) Feature Name/Parameter Default 802.1p to Queue Mapping (802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 93.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 93. Feature Default Values and Default State (continued) Feature Name/Parameter Default Interface Trust Mode 802.1p Interface Shaping Rate 0 802.1p to Queue Mapping (802.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 94. Port characteristics Feature Sets Supported Default Static 802.1Q tagging 256 VID = 1 Max member ports are equal to the number of ports on the switch. Learning process Supports static and dynamic MAC Dynamic learning is enabled by entries default Table 95.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 97. Security Feature Sets Supported Default Management security 1 profile with 20 rules for HTTP/HTTPS access to allow/deny an IP address/subnet All IP addresses allowed Port MAC lock down All ports Disabled Table 98. System setup and maintenance Feature Sets Supported Default Boot code update 1 N/A DHCP/manual IP 1 DHCP enabled/192.168.0.239 Default gateway 1 192.168.0.
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports Table 100.
