User Manual
Table Of Contents
- Insight Managed 8-Port Gigabit (Hi-Power) PoE+ Smart Cloud Switch with NETGEAR FlexPoE Power
- Contents
- 1 Getting Started
- Available publications
- Switch management options and default management mode
- Manage the switch by using the local browser UI
- Access the switch
- Credentials for the local browser UI
- Register and access the switch with your NETGEAR account
- Change the management mode of the switch
- Change the language of the local browser UI
- How to configure interface settings
- Use the Device View of the local browser UI
- 2 Configure System Information
- View or define system information
- Configure the IP network settings for management access
- Configure the time settings
- Manage the denial of service settings
- Configure the DNS settings
- Configure green Ethernet settings
- Manage the Bonjour settings and view Bonjour information
- Control the LEDs
- Use the Device View
- Configure Power over Ethernet
- Configure SNMP
- Configure Link Layer Discovery Protocol
- Configure DHCP snooping
- Set up Power over Ethernet timer schedules
- 3 Configure Switching
- Configure the port settings and maximum frame size
- Configure link aggregation groups
- Configure VLANs
- Manage the basic VLAN settings
- Configure VLAN membership
- View the VLAN status
- Configure the PVID settings for an interface
- Configure a MAC-based VLAN
- Configure protocol-based VLAN groups
- Configure protocol-based VLAN Group membership
- Configure a voice VLAN
- Configure the GARP switch settings
- Configure GARP ports
- Configure Auto-VoIP
- Configure Spanning Tree Protocol
- Configure multicast
- Configure multicast VLAN registration
- View, search, and configure the MAC address table
- Configure Layer 2 loop protection
- 4 Configuring Routing
- 5 Configure Quality of Service
- 6 Manage Switch Security
- Change the local device password for the local browser UI
- Manage the RADIUS settings
- Configure TACACS+ settings
- Configure authentication lists
- Configure management access
- Control access with profiles and rules
- Configure port authentication
- Set up traffic control
- Configure access control lists
- Use the ACL Wizard to create a simple ACL
- Configure a MAC ACL
- Configure MAC ACL rules
- Configure MAC bindings
- View or delete MAC ACL bindings in the MAC binding table
- Configure a basic or extended IPv4 ACL
- Configure rules for a basic IPv4 ACL
- Configure rules for an extended IPv4 ACL
- Configure an IPv6 ACL
- Configure rules for an IPv6 ACL
- Configure IP ACL interface bindings
- View or delete IP ACL bindings in the IP ACL binding table
- Configure VLAN ACL bindings
- 7 Perform Maintenance Tasks
- 8 Manage Power over Ethernet
- 9 Monitor the Switch
- A Configuration Examples
- B Switch Default Settings and Hardware Specifications
Table 88. Security
Feature Sets Supported Default
802.1X All ports Disabled
MAC ACL 100 (shared with IP and IPv6
ACLs)
All MAC addresses allowed
IP ACL 100 (shared with MAC and IPv6
ACLs)
All IP addresses allowed
IPv6 ACL 100 (shared with IP ACL and MAC
ACL)
All IP addresses allowed
Password control access 1 Idle timeout = 5 minutes
Local device password =
password
Management security 1 profile with 256 rules for HTTP,
HTTPS,
TFTP, or SNMP access to
allow or deny an IP address or
subnet
All IP addresses allowed
Port MAC lock down All ports Disabled
Table 89. System setup and maintenance
Feature Sets Supported Default
Boot code update 1 N/A
DHCP/manual IP 1 DHCP enabled/192.168.0.239
Default gateway 1 192.168.0.254
System name configuration 1 Blank
Configuration save/restore 1 N/A
Firmware update 1 N/A
Restore defaults 1 (web and front-panel button) N/A
Dual image support 1 Enabled
Factory reset 1 N/A
Insight Managed 8-Port Gigabit (Hi-Power) PoE+ Smart Cloud Switch with NETGEAR FlexPoE Power
Switch Default Settings and Hardware
Specifications
User Manual470
Table 90. System management
Feature Sets Supported Default
Multi-session web connections 4 Enabled
Time control 1 (Local or SNTP) Local time enabled