User Manual
Table Of Contents
- Insight Managed 8-Port Gigabit (Hi-Power) PoE+ Smart Cloud Switch with NETGEAR FlexPoE Power
- Contents
- 1 Getting Started
- Available publications
- Switch management options and default management mode
- Manage the switch by using the local browser UI
- Access the switch
- Credentials for the local browser UI
- Register and access the switch with your NETGEAR account
- Change the management mode of the switch
- Change the language of the local browser UI
- How to configure interface settings
- Use the Device View of the local browser UI
- 2 Configure System Information
- View or define system information
- Configure the IP network settings for management access
- Configure the time settings
- Manage the denial of service settings
- Configure the DNS settings
- Configure green Ethernet settings
- Manage the Bonjour settings and view Bonjour information
- Control the LEDs
- Use the Device View
- Configure Power over Ethernet
- Configure SNMP
- Configure Link Layer Discovery Protocol
- Configure DHCP snooping
- Set up Power over Ethernet timer schedules
- 3 Configure Switching
- Configure the port settings and maximum frame size
- Configure link aggregation groups
- Configure VLANs
- Manage the basic VLAN settings
- Configure VLAN membership
- View the VLAN status
- Configure the PVID settings for an interface
- Configure a MAC-based VLAN
- Configure protocol-based VLAN groups
- Configure protocol-based VLAN Group membership
- Configure a voice VLAN
- Configure the GARP switch settings
- Configure GARP ports
- Configure Auto-VoIP
- Configure Spanning Tree Protocol
- Configure multicast
- Configure multicast VLAN registration
- View, search, and configure the MAC address table
- Configure Layer 2 loop protection
- 4 Configuring Routing
- 5 Configure Quality of Service
- 6 Manage Switch Security
- Change the local device password for the local browser UI
- Manage the RADIUS settings
- Configure TACACS+ settings
- Configure authentication lists
- Configure management access
- Control access with profiles and rules
- Configure port authentication
- Set up traffic control
- Configure access control lists
- Use the ACL Wizard to create a simple ACL
- Configure a MAC ACL
- Configure MAC ACL rules
- Configure MAC bindings
- View or delete MAC ACL bindings in the MAC binding table
- Configure a basic or extended IPv4 ACL
- Configure rules for a basic IPv4 ACL
- Configure rules for an extended IPv4 ACL
- Configure an IPv6 ACL
- Configure rules for an IPv6 ACL
- Configure IP ACL interface bindings
- View or delete IP ACL bindings in the IP ACL binding table
- Configure VLAN ACL bindings
- 7 Perform Maintenance Tasks
- 8 Manage Power over Ethernet
- 9 Monitor the Switch
- A Configuration Examples
- B Switch Default Settings and Hardware Specifications
Insight Managed 8-Port Gigabit (Hi-Power) PoE+ Smart Cloud Switch with NETGEAR FlexPoE Power
Getting Started User Manual28
For more information about the local device password and the Insight network password,
see
Credentials for the local browser UI on page 28.
11. Click the Login button.
The System Information page displays. The full menu of the local browser UI is now
available and you can configure the switch.
12. After you complete the configuration of the switch, reconfigure the computer that you used
for this process to its original TCP/IP settings.
You can now connect your switch to your network using an Ethernet cable.
Credentials for the local browser UI
The information in this section applies to accessing the switch local browser UI in either
management mode. That is, it does not apply to accessing the NETGEAR Insight app and
Cloud portal.
Note: Until you register and access the switch with your NETGEAR account,
you can access only a limited menu of the local browser UI. This
limitation applies to either management mode.
We recommend that you register and access the switch with your NETGEAR account (see
Register and access the switch with your NETGEAR account on page 29). After you do so,
you can access the local browser UI with the local device password, or if you previously
already added the switch to an Insight network location, with the Insight network password
(for more information, see below).
NETGEAR Insight can affect how you access the switch local browser UI. If you use the
NETGEAR Insight app to discover the switch in your physical network and add the switch to
an Insight network location (this process is referred to as claiming), the switch is
automatically registered to your NETGEAR account.
IMPORTANT:
After you add the switch to an Insight network location, the
Insight network password replaces the switch local device
password. To access the local browser UI, you must enter the
Insight network password. For
information about how the Insight
network password functions, visit
netgear.com/support/product/Insight.aspx. For knowledge base
articles about NETGEAR Insight, visit netgear.com/support.
However, if you use the NETGEAR Insight app to discover the IP address of the switch in
your physical network but do not claim the switch by adding it to an Insight network location,