User Manual
Table Of Contents
- Insight Managed 8-Port Gigabit (Hi-Power) PoE+ Smart Cloud Switch with NETGEAR FlexPoE Power
- Contents
- 1 Getting Started
- Available publications
- Switch management options and default management mode
- Manage the switch by using the local browser UI
- Access the switch
- Credentials for the local browser UI
- Register and access the switch with your NETGEAR account
- Change the management mode of the switch
- Change the language of the local browser UI
- How to configure interface settings
- Use the Device View of the local browser UI
- 2 Configure System Information
- View or define system information
- Configure the IP network settings for management access
- Configure the time settings
- Manage the denial of service settings
- Configure the DNS settings
- Configure green Ethernet settings
- Manage the Bonjour settings and view Bonjour information
- Control the LEDs
- Use the Device View
- Configure Power over Ethernet
- Configure SNMP
- Configure Link Layer Discovery Protocol
- Configure DHCP snooping
- Set up Power over Ethernet timer schedules
- 3 Configure Switching
- Configure the port settings and maximum frame size
- Configure link aggregation groups
- Configure VLANs
- Manage the basic VLAN settings
- Configure VLAN membership
- View the VLAN status
- Configure the PVID settings for an interface
- Configure a MAC-based VLAN
- Configure protocol-based VLAN groups
- Configure protocol-based VLAN Group membership
- Configure a voice VLAN
- Configure the GARP switch settings
- Configure GARP ports
- Configure Auto-VoIP
- Configure Spanning Tree Protocol
- Configure multicast
- Configure multicast VLAN registration
- View, search, and configure the MAC address table
- Configure Layer 2 loop protection
- 4 Configuring Routing
- 5 Configure Quality of Service
- 6 Manage Switch Security
- Change the local device password for the local browser UI
- Manage the RADIUS settings
- Configure TACACS+ settings
- Configure authentication lists
- Configure management access
- Control access with profiles and rules
- Configure port authentication
- Set up traffic control
- Configure access control lists
- Use the ACL Wizard to create a simple ACL
- Configure a MAC ACL
- Configure MAC ACL rules
- Configure MAC bindings
- View or delete MAC ACL bindings in the MAC binding table
- Configure a basic or extended IPv4 ACL
- Configure rules for a basic IPv4 ACL
- Configure rules for an extended IPv4 ACL
- Configure an IPv6 ACL
- Configure rules for an IPv6 ACL
- Configure IP ACL interface bindings
- View or delete IP ACL bindings in the IP ACL binding table
- Configure VLAN ACL bindings
- 7 Perform Maintenance Tasks
- 8 Manage Power over Ethernet
- 9 Monitor the Switch
- A Configuration Examples
- B Switch Default Settings and Hardware Specifications
Insight Managed 8-Port Gigabit (Hi-Power) PoE+ Smart Cloud Switch with NETGEAR FlexPoE Power
Configuring Routing User Manual212
IpOutDiscards The number of output IP datagrams for which no problem was encountered to
prevent their transmission to their destination, but which were discarded (for
example, for lack of buffer space). This counter includes datagrams counted in
ipForwDatagrams if any such packets met this discretionary discard criterion.
IpOutNoRoutes The number of IP datagrams discarded because no route could be found to
transmit them to their destination. This counter includes any packets counted in
ipForwDatagrams that meet this no-route criterion. This includes any datagrams
that a host cannot route because all of its default gateways are down.
IpReasmTimeout The maximum number of seconds that received fragments are held while they
are awaiting reassembly at this entity.
IpReasmReqds The number of IP fragments received that needed to be reassembled at this
entity.
IpReasmOKs The number of IP datagrams successfully reassembled.
IpReasmFails The number of failures detected by the IP reassembly algorithm (for example,
because of timing out, errors, and so on). This is not necessarily a count of
discarded IP fragments because some algorithms can lose track of the number
of fragments by combining them as they are received.
IpFragOKs The number of IP datagrams that were successfully fragmented at this entity.
IpFragFails The number of IP datagrams that were discarded because they needed to be
fragmented at this entity but could not be, for example, because their Don’t
Fragment flag was set.
IpFragCreates The number of IP datagram fragments that were generated as a result of
fragmentation at this entity.
IcmpInMsgs The total number of ICMP messages that the entity received. This counter
includes all those counted by icmpInErrors.
IcmpInErrors The number of ICMP messages that the entity received but that included
ICMP-specific errors (bad ICMP checksums, bad length, and so on).
IcmpInDestUnreachs The number of ICMP Destination Unreachable messages received.
IcmpInTimeExcds The number of ICMP Time Exceeded messages received.
IcmpInParmProbs The number of ICMP Parameter Problem messages received.
IcmpInSrcQuenchs The number of ICMP Source Quench messages received.
IcmpInRedirects The number of ICMP Redirect messages received.
IcmpInEchos The number of ICMP Echo (request) messages received.
IcmpInEchoReps The number of ICMP Echo Reply messages received.
IcmpInTimestamps The number of ICMP Timestamp (request) messages received.
IcmpInTimestampReps The number of ICMP Timestamp Reply messages received.
Table 47. IP routing statistics information (continued)
Field Description