User Manual
Table Of Contents
- Insight Managed 8-Port Gigabit (Hi-Power) PoE+ Smart Cloud Switch with NETGEAR FlexPoE Power
- Contents
- 1 Getting Started
- Available publications
- Switch management options and default management mode
- Manage the switch by using the local browser UI
- Access the switch
- Credentials for the local browser UI
- Register and access the switch with your NETGEAR account
- Change the management mode of the switch
- Change the language of the local browser UI
- How to configure interface settings
- Use the Device View of the local browser UI
- 2 Configure System Information
- View or define system information
- Configure the IP network settings for management access
- Configure the time settings
- Manage the denial of service settings
- Configure the DNS settings
- Configure green Ethernet settings
- Manage the Bonjour settings and view Bonjour information
- Control the LEDs
- Use the Device View
- Configure Power over Ethernet
- Configure SNMP
- Configure Link Layer Discovery Protocol
- Configure DHCP snooping
- Set up Power over Ethernet timer schedules
- 3 Configure Switching
- Configure the port settings and maximum frame size
- Configure link aggregation groups
- Configure VLANs
- Manage the basic VLAN settings
- Configure VLAN membership
- View the VLAN status
- Configure the PVID settings for an interface
- Configure a MAC-based VLAN
- Configure protocol-based VLAN groups
- Configure protocol-based VLAN Group membership
- Configure a voice VLAN
- Configure the GARP switch settings
- Configure GARP ports
- Configure Auto-VoIP
- Configure Spanning Tree Protocol
- Configure multicast
- Configure multicast VLAN registration
- View, search, and configure the MAC address table
- Configure Layer 2 loop protection
- 4 Configuring Routing
- 5 Configure Quality of Service
- 6 Manage Switch Security
- Change the local device password for the local browser UI
- Manage the RADIUS settings
- Configure TACACS+ settings
- Configure authentication lists
- Configure management access
- Control access with profiles and rules
- Configure port authentication
- Set up traffic control
- Configure access control lists
- Use the ACL Wizard to create a simple ACL
- Configure a MAC ACL
- Configure MAC ACL rules
- Configure MAC bindings
- View or delete MAC ACL bindings in the MAC binding table
- Configure a basic or extended IPv4 ACL
- Configure rules for a basic IPv4 ACL
- Configure rules for an extended IPv4 ACL
- Configure an IPv6 ACL
- Configure rules for an IPv6 ACL
- Configure IP ACL interface bindings
- View or delete IP ACL bindings in the IP ACL binding table
- Configure VLAN ACL bindings
- 7 Perform Maintenance Tasks
- 8 Manage Power over Ethernet
- 9 Monitor the Switch
- A Configuration Examples
- B Switch Default Settings and Hardware Specifications
Insight Managed 8-Port Gigabit (Hi-Power) PoE+ Smart Cloud Switch with NETGEAR FlexPoE Power
Getting Started User Manual13
Note: Changes to Insight-manageable settings from the local browser UI might
also create conflicts with the rest of the Insight-managed network to which
the device is connected. While you manage the switch with the local
browser UI, you cannot use the Insight app or Insight Cloud portal. To
reenable management of the device remotely or through the cloud, you
can return the management mode to NETGEAR Insight at any time so that
you can manage the switch with the Insight app or Insight Cloud portal.
To use the local browser UI, after you connect the switch to your network, you must
change the management method to Direct Connect Web-browser Interface (see
Change
the management mode of the switch on page 32).
Manage the switch by using the local
browser UI
This manual describes how to use the local browser UI to manage and monitor the switch.
For information about using the NETGEAR Insight app and Insight Cloud portal to manage
the switch, visit
netgear.com/insight and netgear.com/support/product/Insight.aspx. For
knowledge base articles about NETGEAR Insight, visit netgear.com/support.
Software requirements for the local browser UI
To access the switch by using a web browser, the browser must meet the following software
requirements:
• HTML version 4.0, or later
• HTTP version 1.1, or later
Supported web browsers for the local browser UI
The following browsers were tested and support the local browser UI. Later browser versions
might function fine but were not tested. The supported web browsers include the following:
• Microsoft Internet Explorer (IE) version 11
• Microsoft Edge
• Mozilla Firefox versions 59.0.3
• Chrome version 66.0.3359.139
• Safari on Mac OS 10.1.2 (12603.3.8)