User manual
Table Of Contents
- Contents
- 1. Overview
- 2. Get Started
- 3. Extender Network Settings
- Enable or Disable One WiFi Name
- Enable or Disable Smart Connect
- View Connected Devices
- View WiFi Settings
- Change the WiFi Network Name
- Turn Off the SSID Broadcast to Create a Hidden Network
- Disable or Enable the WiFi Radios
- Change the WiFi Speed
- Use WPS to Add a Computer to the Extender’s WiFi Network
- Deny Access to a Computer or WiFi Device
- Set Up an Access Schedule
- Change the Extender’s Device Name
- Set Up the Extender to Use a Static IP Address
- Use the Extender With MAC Filtering or Access Control
- 4. Maintain and Monitor the Extender
- Change the Extender admin User Name and Password
- Turn Password Protection Off and On
- Recover a Forgotten User Name or Password
- Automatically Adjust for Daylight Saving Time
- Manually Set the Extender Clock
- Back Up and Manage the Extender Configuration
- Return the Extender to Its Factory Default Settings
- Update the Extender Firmware
- Restart the Extender Remotely
- Turn the NETGEAR Logo LED On or Off
- 5. Share USB Storage Devices Attached to the Extender
- USB Device Requirements
- Connect a USB Storage Device to the Extender
- Access a Storage Device Connected to the Router From a Windows Computer
- Map a USB Device to a Windows Network Drive
- Access a Storage Device That Is Connected to the Router From a Mac
- Turn the USB Port Off and On
- Add a Network Folder on a USB Storage Device
- Password-Protect a Folder on a USB Storage Device
- Use the Extender USB Port to Share a Printer
- Change the Network or Device Name
- 6. Use the Extender as a Media Server
- 7. FAQs and Troubleshooting
- 8. Supplemental Information
To use WPS to connect the extender to your WiFi router:
1. Press the WPS button on the extender.
The WPS LED blinks.
2. Within two minutes, press the WPS button on your router or access point.
When the extender connects to your existing WiFi network, the WPS LED on the extender lights solid
white and the Link Status LED lights.
If the Link Status LED does not light, try again. If it still does not light, see Connect With the NETGEAR
Installation Assistant on page 15.
If your router supports the 5 GHz band, your extender attempts to connect to the
router’s 5 GHz band the first time you press the WPS button. If your extender connects
to the router's 5 GHz band, the extender's Link Status LED and Maximum Throughput
LED light solid white. If the LEDs don't light, follow the next step.
Note
3. If your WiFi router supports the 5 GHz band, repeat Steps 1 and 2 to connect the extender to the 5 GHz
band.
The Link Status LED and Maximum Throughput LED light solid white to confirm the connection.
4. Unplug the extender and move it to a new location that is about halfway between your router and the
area with a poor router WiFi signal.
The location that you choose must be within the range of your existing WiFi router network.
5. Use the Link Status LED to help you choose a spot where the extender-to-router connection is optimal.
6. If the Link Status LED doesn’t light amber or white, plug the extender into an outlet closer to the router
and try again.
Keep moving the extender to outlets closer to the router until the Link Status LED lights amber or white.
7. Take your WiFi-enabled computer or mobile device to the location with poor WiFi router coverage.
8. Connect your WiFi-enabled computer or mobile device to the extended network.
Your extender uses the same WiFi network settings as your router for its 2.4 GHz and 5 GHz extended
networks.
For example, if your extender connects to the router’s 2.4 GHz WiFi band, your extender uses your
router’s 2.4 GHz WiFi settings for both its networks:
• Router 2.4 GHz WiFi network name. MyWiFiExample
• Router 5 GHz WiFi network name. MyWiFiExample-5G
• Extended 2.4 GHz WiFi network name. MyWiFiExample
• Extended 5 GHz WiFi network name. MyWiFiExample
Get Started
14
Nighthawk X6S AC3000 Tri-Band WiFi Range Extender