Use and Care Manual
Table Of Contents
- Contents
- 1. Hardware Setup
- 2. Specify Your Internet Settings
- 3. Connect to the Network and Access the Modem Router
- 4. Control Access to the Internet
- 5. Manage Network Settings
- View or change the WAN settings
- Set up a default DMZ server
- Change the Router’s Device Name
- Change the LAN TCP/IP settings
- Specify the IP addresses that the modem router assigns
- Disable the DHCP server feature in the modem router
- Manage reserved LAN IP addresses
- Use the WPS Wizard for WiFi connections
- Specify Basic WiFi Settings
- Change the WiFi Mode
- Change the Transmission Power Control
- Change the WiFi password or the WiFi security
- Set up a guest WiFi network
- Control the WiFi radios
- Set up a WiFi schedule
- Specify WPS settings
- Enable or disable implicit beamforming
- Enable or disable airtime fairness
- Ethernet Port Aggregation
- 6. Manage Your Modem Router
- Update the router firmware
- Change the admin password
- Enable admin password recovery
- Recover the admin password
- View information about the router and the Internet and WiFi settings
- Display the statistics of the Internet port
- Check the Internet connection status
- View and manage logs of router activity
- View devices currently on the network
- View event logs
- Monitor Internet traffic
- Manage the router configuration file
- Remotely access your router using the Nighthawk app
- Disable LED blinking or turn off LEDs
- Set your time zone
- Set the NTP Server
- Specify ReadyDLNA media server settings
- Return the router to its factory default settings
- 7. Share USB Storage Devices Attached to the Modem Router
- USB device requirements
- Connect a USB storage device to the router
- Access a storage device connected to the router from a Windows-based computer
- Map a USB device to a Windows network drive
- Access a storage device that is connected to the router from a Mac
- Enable FTP access within your network
- View network folders on a storage device
- Add a network folder on a USB storage device
- Edit a network folder on a USB storage device
- Safely remove a USB storage device
- 8. Use Dynamic DNS to Access USB Storage Devices Through the Internet
- 9. Use VPN to Access Your Network
- 10. Manage Port Forwarding and Port Triggering
- 11. Troubleshooting
- 12. Supplemental Information
USB device requirements
The modem router works with most USB-compliant external flash and hard drives. For
the most up-to-date list of USB devices that the modem router supports, visit
kb.netgear.com/app/answers/detail/a_id/18985/~/readyshare-usb-drives-compatibility-list.
Some USB external hard drives and flash drives require you to load the drivers onto the
computer before the computer can access the USB storage device. Such USB storage
devices do not work with the modem router.
The modem router supports the following file system types for full read/write access:
•
FAT16
•
FAT32
•
NTFS
•
NTFS with compression format enabled
•
Ext2
•
Ext3
•
Ext4
•
HFS
•
HFS+
Connect a USB storage device to the router
ReadySHARE lets you access and share USB storage devices that are connected to a
USB port on the modem router. (If your USB storage device uses special drivers, it is
not compatible.)
To connect a USB device:
1. Insert your USB storage device into a USB port on the modem router.
2.
If your USB storage device uses a power supply, connect it.
You must use the power supply when you connect the USB storage device to the
modem router.
When you connect the USB storage device to the router USB port, it might take up
to two minutes before it is ready for sharing. By default, the USB storage device is
available to all computers on your local area network (LAN).
User Manual83Share USB Storage Devices
Attached to the Modem Router
Nighthawk AX6 AX2700 WiFI Cable Modem Router Model CAX30