User's Manual
Table Of Contents
- ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
- Contents
- About This Manual
- Chapter 1 Introduction
- Chapter 2 Basic Installation and Configuration
- Wireless Equipment Placement and Range Guidelines
- Understanding WNDAP350 Wireless Security Options
- Installing the WNDAP350 wirelss access point
- Logging In Using the Default IP Address
- Setting Basic IP Options
- Wireless Settings
- Setting Up and Testing Basic Wireless Connectivity
- Understanding Security Profiles
- SSID and WEP/WPA Settings Setup Form
- Configuring the RADIUS Server Settings
- Setting up a Security Profile
- Configuring WEP
- Configuring WPA with RADIUS
- Configuring WPA2 with RADIUS
- Configuring WPA and WPA2 with RADIUS
- Configuring WPA-PSK
- Configuring WPA2-PSK
- Configuring WPA-PSK and WPA2-PSK
- Restricting Wireless Access by MAC Address
- Chapter 3 Management
- Remote Management
- Remote Console
- Upgrading the Wireless Access Point Software
- Configuration File Management
- Changing the Administrator Password
- Enabling the SysLog Server
- Using Activity Log Information
- Viewing General Summary Information
- Viewing Network Traffic Statistics
- Viewing Available Wireless Station Statistics
- Enabling Rogue AP Detection
- Viewing Rogue AP Statistics
- Packet Capture
- Chapter 4 Advanced Configuration
- Chapter 5 Troubleshooting and Debugging
- No lights are lit on the wireless access point.
- The Wireless LAN activity light does not light up.
- The LAN light is not lit.
- I cannot access the Internet or the LAN with a wireless capable computer.
- I cannot connect to the WNDAP350 to configure it.
- When I enter a URL or IP address I get a timeout error.
- Using the Reset Button to Restore Factory Default Settings
- Appendix A Default Settings and Technical Specifications
- Appendix B Related Documents
- Appendix C 2.0 Command Line Reference
- Index
ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
4-8 Advanced Configuration
v2.0, April 2013
• Aggregation Length (1024-65535) (11na only): The aggregation length defines the size
of aggregated packets. Larger aggregation lengths may sometimes lead to better network
performance. The default is 65535.
• A-MPDU (11na only): Aggregated MAC Protocol Data Unit. Aggregates several MAC
frames into a single large frame to achieve higher throughput. The default is enabled.
• RIFS Transmission (11na only): Reduced Interframe Space. RIFS transmissions are
shorter than other interframe spaces, and if enabled allow transmission of successive
frames at different transmit powers. The default is disabled. The default is disabled.
• DTIM Interval: The Delivery Traffic Indication Message. Specifies the data beacon rate
between 1 and 255. The default is 3.
• Client Isolation: This option, when enabled, blocks communication between wireless
clients that are associated to different VAPs. The default is Disable.
• Max Wireless Clients: The number of wireless clients that can associate with the AP at
one time. The default is 63.
5. Click Apply to enable the Wireless Settings.
Configuring Advanced QoS Settings
Wireless Multimedia Extension (WME) or Wi-Fi Multimedia (WMM) is a subset of the 802.11e
standard. WME allows wireless traffic to have a range of priorities, depending on the type of data.
Time-dependent information, such as video or audio, has a higher priority than normal traffic. For
WME to function correctly, Wireless clients must also support WME.
Figure 4-5 shows the Quality of Service (QoS) screen. For most networks, the default QoS queue
parameter settings work well.Quality of Service provides you with the ability to specify
parameters on multiple queues for increased throughput and better performance of differentiated
wireless traffic, like Voice-over-IP (VoIP), other types of audio, video, and streaming media, as
well as traditional IP data.
To configure advanced QoS settings, on the Configuration tab select Wireless, select Advanced,
and then select QoS Settings. The QoS Settings screen dis pa lys: