User's Manual
Table Of Contents
- ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
- Contents
- About This Manual
- Chapter 1 Introduction
- Chapter 2 Basic Installation and Configuration
- Wireless Equipment Placement and Range Guidelines
- Understanding WNDAP350 Wireless Security Options
- Installing the WNDAP350 wirelss access point
- Logging In Using the Default IP Address
- Setting Basic IP Options
- Wireless Settings
- Setting Up and Testing Basic Wireless Connectivity
- Understanding Security Profiles
- SSID and WEP/WPA Settings Setup Form
- Configuring the RADIUS Server Settings
- Setting up a Security Profile
- Configuring WEP
- Configuring WPA with RADIUS
- Configuring WPA2 with RADIUS
- Configuring WPA and WPA2 with RADIUS
- Configuring WPA-PSK
- Configuring WPA2-PSK
- Configuring WPA-PSK and WPA2-PSK
- Restricting Wireless Access by MAC Address
- Chapter 3 Management
- Remote Management
- Remote Console
- Upgrading the Wireless Access Point Software
- Configuration File Management
- Changing the Administrator Password
- Enabling the SysLog Server
- Using Activity Log Information
- Viewing General Summary Information
- Viewing Network Traffic Statistics
- Viewing Available Wireless Station Statistics
- Enabling Rogue AP Detection
- Viewing Rogue AP Statistics
- Packet Capture
- Chapter 4 Advanced Configuration
- Chapter 5 Troubleshooting and Debugging
- No lights are lit on the wireless access point.
- The Wireless LAN activity light does not light up.
- The LAN light is not lit.
- I cannot access the Internet or the LAN with a wireless capable computer.
- I cannot connect to the WNDAP350 to configure it.
- When I enter a URL or IP address I get a timeout error.
- Using the Reset Button to Restore Factory Default Settings
- Appendix A Default Settings and Technical Specifications
- Appendix B Related Documents
- Appendix C 2.0 Command Line Reference
- Index
ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
Basic Installation and Configuration 2-33
v2.0, April 2013
• To configure WPA with RADIUS, see “Configuring WPA with RADIUS” on page 2-35.
• To configure WPA2 with RADIUS, see “Configuring WPA2 with RADIUS” on
page 2-37.
• To configure WPA and WPA2 with RADIUS, see “Configuring WPA and WPA2 with
RADIUS” on page 2-38.
• To configure WPA-PSK, see “Configuring WPA-PSK” on page 2-40.
• To configure WPA2-PSK, see “Configuring WPA2-PSK” on page 2-41.
• To configure WPA-PSK and WPA2-PSK, see “Configuring WPA-PSK and WPA2-PSK”
on page 2-42.
8. Wireless Client Security Separation is disabled by default. If enabled, the associated
wireless clients will not be able to communicate with each other.
9. If the hubs/switches on your LAN support the VLAN (802.1Q) standard and this feature has
been enabled, the default VLAN ID for WNDAP350 will be associated with each profile. The
default Profile VLAN ID must match the IDs used by other network devices.
10. Click Apply to save your Security Profile settings.
11. Click Back. Your new settings will appear in the Security Profiles table identified by the
Profile Name of the profile. A VLAN ID will also be assigned to your profile.
To enable your Security Profile:
1. Check the radio box in the Enable column next to your profile.
2. Click Apply. Your Security Profile will be enabled. If you enabled VLAN 802.1Q, your
VLAN Profile will also be enabled. (See “Setting Basic IP Options” on page 2-13 to enable
VLAN 802.1Q.)
Configuring WEP
To configure WEP data encryption:
1. From the Network Authentication drop-down menu, choose either Open System or Shared
Key authentication.
Note: Security Profiles that share the same type of network authentication need not
share the same passphrase or keys.