User's Manual
Table Of Contents
- ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
- Contents
- About This Manual
- Chapter 1 Introduction
- Chapter 2 Basic Installation and Configuration
- Wireless Equipment Placement and Range Guidelines
- Understanding WNDAP350 Wireless Security Options
- Installing the WNDAP350 wirelss access point
- Logging In Using the Default IP Address
- Setting Basic IP Options
- Wireless Settings
- Setting Up and Testing Basic Wireless Connectivity
- Understanding Security Profiles
- SSID and WEP/WPA Settings Setup Form
- Configuring the RADIUS Server Settings
- Setting up a Security Profile
- Configuring WEP
- Configuring WPA with RADIUS
- Configuring WPA2 with RADIUS
- Configuring WPA and WPA2 with RADIUS
- Configuring WPA-PSK
- Configuring WPA2-PSK
- Configuring WPA-PSK and WPA2-PSK
- Restricting Wireless Access by MAC Address
- Chapter 3 Management
- Remote Management
- Remote Console
- Upgrading the Wireless Access Point Software
- Configuration File Management
- Changing the Administrator Password
- Enabling the SysLog Server
- Using Activity Log Information
- Viewing General Summary Information
- Viewing Network Traffic Statistics
- Viewing Available Wireless Station Statistics
- Enabling Rogue AP Detection
- Viewing Rogue AP Statistics
- Packet Capture
- Chapter 4 Advanced Configuration
- Chapter 5 Troubleshooting and Debugging
- No lights are lit on the wireless access point.
- The Wireless LAN activity light does not light up.
- The LAN light is not lit.
- I cannot access the Internet or the LAN with a wireless capable computer.
- I cannot connect to the WNDAP350 to configure it.
- When I enter a URL or IP address I get a timeout error.
- Using the Reset Button to Restore Factory Default Settings
- Appendix A Default Settings and Technical Specifications
- Appendix B Related Documents
- Appendix C 2.0 Command Line Reference
- Index
ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
2-4 Basic Installation and Configuration
v2.0, April 2013
• Turn Off the Broadcast of the Wireless Network Name (SSID). If you disable broadcast of
the SSID, only devices that have the correct SSID can connect. This nullifies the wireless
network “discovery” feature of some products such as Windows XP, Vista and Unix systems
but the data is still fully exposed to a determined snoop using specialized test equipment like
wireless sniffers.
• Use WEP. Wired Equivalent Privacy (WEP) data encryption provides data security. WEP
open authentication and WEP data encryption will block all but the most determined
eavesdropper.
• Use WPA or WPA-PSK. Wi-Fi Protected Access (WPA) data encryption provides data
security. The very strong authentication along with dynamic per frame rekeying of WPA make
it virtually impossible to compromise. Because this is a new standard, wireless device driver
and software availability may be limited.
Installing the WNDAP350 wirelss access point
Before installing the ProSafe Dual Band Wireless N Access Point WNDAP350 , you should make
sure that your Ethernet network is up and working. You will be connecting the access point to the
Ethernet network so that computers with 802.11b/g/n or 802.11a/n wireless adapters will be able to
communicate with computers on the Ethernet network. In order for this to work correctly, verify
that you have met all of the system requirements, shown on “System Requirements” on page 1-5.
Setting up the WNDAP350 wirelss access point
To set up the WNDAP350 wirelss access point:
1. Prepare a computer with an Ethernet adapter. If this computer is already part of your network,
record its TCP/IP configuration settings.
Note: WEP and TKIP provide only legacy rates of operation. So, AES is the
recommended solution to use the 802.11n rates and speed.
Tip: Before mounting the WNDAP350 in a high location, first set up and test the
WNDAP350 to verify wireless network connectivity.