User's Manual
Table Of Contents
- ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
- Contents
- About This Manual
- Chapter 1 Introduction
- Chapter 2 Basic Installation and Configuration
- Wireless Equipment Placement and Range Guidelines
- Understanding WNDAP350 Wireless Security Options
- Installing the WNDAP350 wirelss access point
- Logging In Using the Default IP Address
- Setting Basic IP Options
- Wireless Settings
- Setting Up and Testing Basic Wireless Connectivity
- Understanding Security Profiles
- SSID and WEP/WPA Settings Setup Form
- Configuring the RADIUS Server Settings
- Setting up a Security Profile
- Configuring WEP
- Configuring WPA with RADIUS
- Configuring WPA2 with RADIUS
- Configuring WPA and WPA2 with RADIUS
- Configuring WPA-PSK
- Configuring WPA2-PSK
- Configuring WPA-PSK and WPA2-PSK
- Restricting Wireless Access by MAC Address
- Chapter 3 Management
- Remote Management
- Remote Console
- Upgrading the Wireless Access Point Software
- Configuration File Management
- Changing the Administrator Password
- Enabling the SysLog Server
- Using Activity Log Information
- Viewing General Summary Information
- Viewing Network Traffic Statistics
- Viewing Available Wireless Station Statistics
- Enabling Rogue AP Detection
- Viewing Rogue AP Statistics
- Packet Capture
- Chapter 4 Advanced Configuration
- Chapter 5 Troubleshooting and Debugging
- No lights are lit on the wireless access point.
- The Wireless LAN activity light does not light up.
- The LAN light is not lit.
- I cannot access the Internet or the LAN with a wireless capable computer.
- I cannot connect to the WNDAP350 to configure it.
- When I enter a URL or IP address I get a timeout error.
- Using the Reset Button to Restore Factory Default Settings
- Appendix A Default Settings and Technical Specifications
- Appendix B Related Documents
- Appendix C 2.0 Command Line Reference
- Index
ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
4-14 Advanced Configuration
v2.0, April 2013
Configuring a Point-to-Multi-Point Wireless Bridge
To configure a point-to-multi-point wireless bridge as shown in Figure 4-9:
1. Under the Configuration tab, select Wireless Bridge. Then, select Bridging. The Bridging
screen displays.
2. Configure the Operating Mode of the WNDAP350 wirelss access points.
• WNDAP350 (AP1) on LAN Segment 1 in Point-to-Point Bridge mode with the Remote
MAC Address of AP2.
• Because it is in the central location, configure WNDAP350 (AP2) on LAN Segment 2 in
Point-to-Multi-Point Bridge mode. The MAC addresses of the adjacent APs are required
in AP2.
• Configure the WNDAP350 (AP3) on LAN 3 in Point-to-Point Bridge mode with the
Remote MAC Address of AP2.
3. Verify the following parameters for all access points:
• Verify that the LAN network configuration the WNDAP350 wirelss access points are
configured to operate in the same LAN network address range as the LAN devices
• Only one access point is configured in Point-to-Multi-Point Bridge mode, and all the
others are in Point-to-Point Bridge mode.
• All access points must be on the same LAN. That is, all the APs LAN IP address must be
in the same network.
Figure 4-9 Wireless point-to-multipoint bridge setup
'Master' AP in
Point-to-Multi-Point
Bridge Mode
LAN
Segment 1
192.168.0.1
Router
AP in
Point-to-Point
Bridge Mode
Hub or Switch
LAN
Segment 3
AP in
Point-to-Point
Bridge Mode
LAN
Segment 2
Hub or Switch
AP1
ETHERNET
RESET
5-12V DC
AP3
ETHERNET
RESET
5-12V DC
AP2
ETHERNET
RESET
5-12V DC