Netac AirTrack T610 Wireless Broadband Router User's Manual Netac Technology Co., Ltd. http://www.netac.
REMARKS This manual contains information protected by copyright law. All rights are reserved. No part of this document may be used or reproduced in any form or by any means, or stored in a database/retrieval system without prior written permission from Netac Technology Co., Ltd. Netac fulfill the repair service during warranty period in promised support range. This product is not guaranteed for its compatibility with all kinds of computers and Operating System. Netac Technology Co., Ltd.
Radio Frequency Interference Remarks This equipment has passed the test, and affirmed that it compatible to constrain B type digital equipment in section 15 of FCC. This constraint is mainly used to protect the home-keeping equipment, avoid to be interfered banefully. This equipment can produce, use, and radiate radio frequency energy. If you don't install and use according to the descriptive manual, the equipment may interfere the wireless communication banefully.
CAUTION 1. Please use original power adapter of Netac AirTrack T610 Wireless Broadband Router, if you use other kinds, it maybe destroy the product. 2. Prevent to get an electric shock and be destroyed, please don’ t replug the power of Netac AirTrack T610 Wireless Broadband Router by wet hand. 3. Avoid to be destroyed, please don’ t put Netac AirTrack T610 Wireless Broadband Router under burning sun or in dirty place. 4.
Table of Contents 1 Introduction ........................................................................................1 1.1 Welcome.............................................................................................................. 1 1.2 Checklist .............................................................................................................. 1 1.3 Product function................................................................................................... 1 1.4 Appearance .
Netac AirTrack T610 Wireless Broadband Router 1 Introduction 1.1 Welcome Thank you for purchasing Netac AirTrack T610 Wireless Broadband Router. Netac AirTrack T610 Wireless Broadband Router is a wireless network product for SOHO and family, it is developed successfully based on the environment of wirelessly broadband access technology oncoming and wired network extend to wirelessly network.
Netac AirTrack T610 Wireless Broadband Router ü IP address filter ü MAC filter ü Support port forward ü Support DMZ 1.4 Appearance LEDs Figure 1.1 Appearances Table 1.1 LEDs LED Power Status Description Light Equipment power turned on. Off Equipment power turned off or failure. LAN（1，2， Light 3，4） WAN Wireless LAN1, 2, 3, 4 port build Ethernet connection. Blink LAN1, 2, 3, 4 port is transferring data. Light WAN port build Ethernet connection. Blink WAN port is transferring data.
Netac AirTrack T610 Wireless Broadband Router 2 Logging on configuration page Netac AirTrack T610 Wireless Broadband Router (T610) is configured by a Web page with password. Table2.1 list the default IP address, user name and password of T610 configuration Web. Table 2.1 T610's default Parameter Default IP Address 192.168.1.1 User name admin Password password User can log on T610's configuration page by desktop configured Ethernet Network Interface Card or laptop configured 802.
Netac AirTrack T610 Wireless Broadband Router a. When you build T610 on the wall, avoid to fall down be destroyed, please fix it well. b. Leave enough roomage around T610, so that can dispel heat normally. 2. Connect T610's 1# LAN port with the Network Interface Card port of computer A through an Ethernet cable. Note: a. The length of Ethernet cable connected to computer or LAN cannot exceed 100 meters. b.
Netac AirTrack T610 Wireless Broadband Router Figure 2.2 "Network and Dial-up Connections" dialog box 2. Double click "Local Area Connection" icon; the "Local Area Connection Status" dialog box will pop-up, as Figure 2.3. Figure 2.3 "Local Area Connection Status" dialog box 3. Click "Properties" button, bring up the "Local Area Connection Properties" dialog box, as Figure 2.4. Figure 2.4 "Local Area Connection Properties" dialog box 4.
Netac AirTrack T610 Wireless Broadband Router Figure 2.5 "Select Network Component Type" dialog box 5. Select “Protocol”, click “Add”, Figure 2.6 shows the pop-up dialog box, select “Internet Protocol (TCP/IP)”, click “OK”, then you can finish installing and go back to the interface as figure 2.4. Figure 2.6 "Select Network Protocol" dialog box 6. Select “Internet Protocol (TCP/IP)”in the figure 2.4, click “Properties”button, Figure 2.7 shows the "Internet Protocol (TCP/IP) Properties”dialog box.
Netac AirTrack T610 Wireless Broadband Router Figure 2.7 "Internet Protocol (TCP/IP) Properties" dialog box 7. Select "Obtain an IP address automatically" or "Use the following IP address", and then click "OK". Figure 2.8 Internet Protocol (TCP/IP) Properties setup Note: a. With built-in DHCP server, T610 can assign IP address to LAN host computer automatically, it is suggested that users select “Obtain an IP address automatically”.
Netac AirTrack T610 Wireless Broadband Router mask is 255.255.255.0, please make sure that the configuration is correct, or obtain the correct parameter configuration from network manager. b. Computer B (Wireless Network Interface Card user), please select the “Local Area Connection” opposite to Wireless Network Interface Card in figure 2.2, and configure it refer to the step as said. 2.3 Check Configuration Power on T610, the power indicator get bright, and T610 will self check about 30 seconds.
Netac AirTrack T610 Wireless Broadband Router Figure 2.10 communication successfully 3. If display message as follows: "Pinging 192.168.1.1 with 32 bytes of data: Request timed out." It means connected unsuccessfully. See Figure 2.11. Figure 2.11 communication unsuccessfully Communication unsuccessfully indicates wrong in the install, please check the items in turn as follows: a. Make sure the computer is connected to T610 properly.
Netac AirTrack T610 Wireless Broadband Router Computer B (Wireless Network Interface Card user) also can check the status of Computer and T610's connection by command ping. If display "Request timed out.", please check the items in turn as follows: a. Make sure the Wireless Network Interface Card working normally.
Netac AirTrack T610 Wireless Broadband Router Figure 2.13 Open Internet Explorer Please input user name and password in the pop-up logging dialog box, as Figure 2.14. Figure 2.14 logging The default user name is "admin", password is "password", click "OK" or press "Enter", then you can log on T610's configuration page by administrator ship. At the same time you can select "Save this password in your password list", next visit will enter the configuration page directly without the logging dialog box.
Netac AirTrack T610 Wireless Broadband Router Figure 2.
Netac AirTrack T610 Wireless Broadband Router 3 Router Configuration Configure T610 by the following pages, Figure 2.15 shows: Radio Setting The Radio Setting page allows the user to configure the connection of WLAN. Security The Security page allows the user to configure the security of WLAN. WAN The WAN page allows the user to configure the connection of WAN. LAN The LAN page allows the user to configure the connection of LAN.
Netac AirTrack T610 Wireless Broadband Router 3.1 Radio Setting Figure 3.1 Radio Setting Page Table 3.1 Radio Setting Field Description Service Set ID (SSID) Wireless Network Name. Radio Preamble Select: Short preamble, Long preamble or Auto. AP Mode Select B only, G only or mixed mode. G Mode protection Select CTS ONLY, RTS-CTS or force 802.11g mode off. Rate Selection For B Select transmit rate: 1, 2, 5.5, 11Mbps or Auto. Rate Selection For G Select transmit rate: 1, 2, 5.
Netac AirTrack T610 Wireless Broadband Router 3.2 Security Figure 3.2 Security Page Table 3.2 Security Configurations Field Description WPA Mode Disable/enable the WPA encryption. Pass Phrase Pass phrase is used to generate the WPA keys. WEP Encryption Disable/enable the WEP encryption. Transmit WEP Key Select transmit WEP key from Keys1-4. WEP Key Size Select WEP Key size: 40 bits or 104 bits, you can also do not set WEP key size. WEP Key 1-4 WEP keys.
Netac AirTrack T610 Wireless Broadband Router 3.3 WAN Figure 3.3 WAN Page Table 3.3 WAN Configurations Field Protocol IP Address Subnet Mask Description Set the method to obtain IP address for WAN connection. Select DHCP, Static or PPPoE. Set the WAN IP address of T610. (It is available when use Static protocol.) Allow the user to specify a subnet mask. (It is available when use Static protocol.) Gateway Allow the user to specify a gateway. (It is available when use Static protocol.
Netac AirTrack T610 Wireless Broadband Router Password user name and password. Status The relevant information for WAN connection. 3.4 LAN Figure 3.4 LAN Page Table 3.4 LAN Configurations Field Description Set the IP address of T610. Default: 192.168.1.1. IP Address Note: To configure T610, the user must access T610 from a PC that is on the same subnet. Subnet Mask Allow the user to specify a subnet mask. Default: 255.255.255.0. Enable DHCP Service Disable/Enable DHCP server.
Netac AirTrack T610 Wireless Broadband Router 3.5 MAC Filter Figure 3.5 MAC Filter Page Table 3.5 MAC Filter Settings Field Description MAC Filter Enable/Disable MAC filter mode. Filter Mode Allow or deny clients listed in "Stations List" to access T610. Stations List Up to 32 MAC addresses can be listed. MAC addresses List of MAC addresses to filter.
Netac AirTrack T610 Wireless Broadband Router 3.6 IP Filter Figure 3.6 IP Filter Page Table 3.6 IP Filter Settings Field Description IP Filter Enable/Disable IP filter mode. Filter Mode Allow or deny clients listed in "Stations List" to access T610. Stations List Up to 32 IP addresses can be listed. IP Addresses List of IP addresses to filter.
Netac AirTrack T610 Wireless Broadband Router 3.7 Port Forward Figure 3.7 Port Forward Page Table 3.7 Port Forward Settings Field Port forward list DMZ Description Forward the data package sent from WAN port to T610 to the specified port of the computer with specified IP address. Forward all data package sent from WAN port to T610 to the specified IP address.
Netac AirTrack T610 Wireless Broadband Router 3.8 Admin Figure 3.8 Admin Page Table 3.8 Admin Settings Field New Username Password Firmware Version Select File Description To modify the user name, enter the new user name in the New Username field and click Apply. To modify the password, enter the new password in the New Password and Reconfirm Password fields and click Apply. Displays the firmware version. To upgrade the firmware, click the Browse button and select the image file.
Netac AirTrack T610 Wireless Broadband Router 3.9 Association Table Figure 3.9 Association Table Page This Page displays the MAC address of wireless user, which connected to this device.
Netac AirTrack T610 Wireless Broadband Router 4 Mode of build network Note: The AirTrack T100, AirTrack T200, AirTrack T300, AirTrack T700 in the following pictures are products of Netac, AirTrack T100, AirTrack T200 and AirTrack T300 are Wireless Network Interface Card, AirTrack T700 is Broadband Router. You can choose the product of the same kind from the other companies to build network. 4.1 Build at-home network 1.
Netac AirTrack T610 Wireless Broadband Router Access Internet through ADSL Modem Access Internet through Cable Modem/optic fiber Access Internet through optic fiber Figure 4.2 WAN configurations l Configure LAN. Enter the LAN page, we suggest you to enable DHCP server, and configure start IP address and end IP address, such as: the start IP address is "192.168.1.2", the end IP address is "192.168.1.254". Also you can use default configuration without any change. Figure 4.
Netac AirTrack T610 Wireless Broadband Router l Radio Setting. Enter the Radio Setting page, the default network name is "AirTrack", modify it to "Home" or other specialized network name. Figure 4.4 Radio setting 4.2 Build network of enterprise 1. Building requirement As a gateway of enterprise LAN, T610 access Internet through ADSL Modem/optic fiber. l Modify the logging user name to "AirTrack", and password to "netac". l Enable DHCP server. l The start IP address is "192.168.1.
Netac AirTrack T610 Wireless Broadband Router Figure 4.6 Admin page l Enter the LAN page. Enable DHCP server, set the start IP address to "192.168.1.10", the end IP address to "192.168.1.100". Figure 4.7 LAN configuration l Configure WAN. According to the access mode, there are two configuration: use PPPoE protocol when access Internet through ADSL Modem, input "szhomeg@163.
Netac AirTrack T610 Wireless Broadband Router Access Internet through optic fiber Figure 4.8 WAN configurations l Enter IP Filter page. Figure 4.9 details the configuration. Figure 4.9 IP filter l Radio settings. Enter the Radio Setting page, the default network name is "AirTrack", modify it to "ABC". Figure 4.
Netac AirTrack T610 Wireless Broadband Router 5 Specifications Table 5.1 Specifications Item Compatible Standard Network Interface Description IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX 802.11b/g One 10/100Mbps uplink interface (RJ45 type) 4-port 10/100Mbps downlink Ethernet interface (RJ45 type) 802.11b/g wireless LAN interface LED Power, Wireless, WAN, LAN Antenna Dipole Antenna Maximal Launch Power 20±2dBm Wireless Frequency Range 2.4000～2.4835 GHz Wireless Modulation Mode 802.
Netac AirTrack T610 Wireless Broadband Router Appendix A: FAQ 1. The power indicator of Netac AirTrack T610 Wireless Broadband Router not bright, why? Answer: Please check the items as follows: A. Make sure the power adapter is original-packaged. B. Make sure your Netac AirTrack T610 Wireless Broadband Router connected to power properly. C. Make sure your Netac AirTrack T610 Wireless Broadband Router is powered on. 2.
Netac AirTrack T610 Wireless Broadband Router Appendix B: Contact Netac Netac Technology Co., Ltd. 6F, Incubator Building, China Academy or Science & Tech Development, No.1 High-tech South St, Shenzhen, China 518057 Tel: +86-755-26727800, 26727449 (English) Fax: +86-755-26727610, 26727620 Website: http://www.netac.com Email: sales@netac.com overseas@netac.com support@netac.
Netac AirTrack T610 Wireless Broadband Router Appendix C: Glossary 802.11 A family of specifications developed by the IEEE for WLAN technology. 802.11b An extension to 802.11 that applies to WLANS and provides 11 Mbps transmission rate in the 2.4GHz band. 802.11b use only DSSS. 802.11g An extension to 802.11 that applies to WLANS and provides 54 Mbps transmission rate in the 2.4 GHz band. 802.11g use OFDM and is backward compatible with 802.11b.
Netac AirTrack T610 Wireless Broadband Router CCK Complementary Code Keying. CTS/RTS Clear to Send/Request to Send. They are two special administrant data frame, a protecting mechanism to avoid the conflict in WLAN. DHCP Dynamic Host Configuration Protocol. DSSS Direct Sequence Spread Spectrum. DSSS is one of two types of spread spectrum radio. DTIM Delivery Traffic Indication Message. FCC Federal Communications Commission. HTTP Hypertext Transfer Protocol.
Netac AirTrack T610 Wireless Broadband Router LAN Local Area Network. MAC Media Access Control. Mbps Megabits Per Second. OFDM Orthogonal Frequency Division Multiplexing. OSI Open System Interconnect. P2P Point-to-Point. PMP Point-to-Multipoint. QoS Quality of Service. RF Radio Frequency. RJ-45 Ethernet Interface of A type. WAN Wide Area Network. WEP Wired Equivalent Privacy. A security protocol for WLANs defined in the IEEE 802.11 standard. Wi-Fi Wireless Fidelity (IEEE 802.11) .
Netac AirTrack T610 Wireless Broadband Router WLAN Wireless Local Area Network.
