Installation Guide for TM Optical Bypass Switch with Heartbeat 800-0148-001 Doc.
Optical Bypass Switch with Heartbeat Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optical Bypass Switch with Heartbeat PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using a Net Optics Optical Bypass Switch you agree to the terms and conditions of usage set forth by Net Optics, Inc. No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual property rights associated with the technology described in this manual. This manual is intended to assist with installing Net Optics products into your network.
Optical Bypass Switch with Heartbeat Introduction Thank you for choosing the most versatile Optical Bypass Switch available today. Whether you are a novice or an expert, this installation guide is designed to help answer any questions and to provide a quick set-up reference. Net Optics Optical Bypass Switches with Heartbeat provide a permanent and trouble-free access port for in-line network security and monitoring devices.
Optical Bypass Switch with Heartbeat Key Features Passive, Secure Technology • Fail-open monitoring with any GigaBit fiber in-line appliance at speeds of 1000 Mbps • Protects against power, link, and application failure • Increased reliability on critical network links • High-speed optical switching with minimal insertion loss • Configurable timeout (heartbeat) and retry • Custom Heartbeat packet option • Fully RoHS Compliant Ease of Use • LED indicators show power, speed, link, and activity status • Fro
Optical Bypass Switch with Heartbeat Product Diagrams Bypass Indicator LEDs Network A ® B Monitor 1 Optical Bypass Switch 2 BYPASS ON OFF 2 ACT 1 OUT IN OUT IN OUT IN OUT LINK A IN B 1 2 LASER CAUTION! www.netoptics.com Network Ports A&B Monitor Ports C&D Power LEDs Activity & Link LEDs Figure 1: Front View Panel Figure 2: Rear View Panel RS232 Port PWR DC Jack Terminals Figure 3: Application Diagram Silk Screen Diagram 2 + Volt 3.
Optical Bypass Switch with Heartbeat Bypass Modes The Optical Bypass Switch with Heartbeat bypasses attached in-line device when one of three events occurs: • Power loss to the switch • Link failure • Application failure Two LEDs on the front of the Optical Bypass Switch indicate whether the switch is bypassing the connected appliance or not. When the Bypass ON indicator is illuminated, the bypass switch has not received the heartbeat packet as expected and is in Bypass Enabled mode.
Optical Bypass Switch with Heartbeat Power Loss Bypass The Optical Bypass Switch protects link integrity when the attached in-line device loses power. To install the Optical Bypass Switch for this type of protection, the switch should share the same power source as the in-line appliance. If you are using redundant power supplies for the switch, make sure that both are connected to the same power source as the in-line device.
Optical Bypass Switch with Heartbeat IPX Packet Packet Contents (Hex) ----------------------------- Description ---------------- 00 50 C2 3C 60 00 00 50 C2 3C 60 01 81 37 FF FF 00 30 00 00 00 00 40 04 EC A2 C6 13 01 02 C6 13 01 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 82 A2 BA 71 MAC DA Net Optics MAC SA Net Optics Packet Type IPX CRC IP Packet Packet Contents (Hex) ----------------------------- Description ---------------- 00 50 C2 3C 60 00 00 50 C2 3C
Optical Bypass Switch with Heartbeat Unpacking and Inspection Unpack the Optical Bypass Switch, power supplies, and cables provided. Each Optical Bypass Switch is delivered with the following: • 2 Power supplies • 2 LC fiber cables (models BPO-HBSX-LC0, BPO-HB-LX/SX, and BPOHBLX-SC/LC) or 2 LC-to-SC cables (model BPO-HBSX-SC/LC) • 1 DB-9 RS232 cable • 1 Manual You may have also purchased a panel for rack mounting the bypass switch and an extended warranty.
Optical Bypass Switch with Heartbeat Link Fault Detect You can set the bypass switch to drop the remaining full-duplex link when one side fails. The Link Fault Detect features ensures that connected devices are aware of a failure on both sides of the link. Bypass Detect You can set the Monitor Ports to cycle on and off while the bypass switch is in Bypass Enabled mode. In Bypass Detect mode, the Monitor Ports cycle through five seconds off followed by fifteen seconds on.
Optical Bypass Switch with Heartbeat The following commands are listed: a = Input Timeouts b = Input Configuration c = Input Heartbeat Packet d = Display Configuration e = Display Heartbeat Packet z = Reset to Factory Defaults To set the timeout values: 1. Type a and press Enter to set the timeout values. 2. At the input time out period prompt, enter the number of seconds between each heartbeat (1-254 seconds). Press Enter. 3.
Optical Bypass Switch with Heartbeat 3. Enter packet bytes in Hex format in the following order: MAC DA Net Optics (6 bytes) MAC SA Net Optics (6 bytes) Packet Type (2 bytes) Packet Bytes CRC (4 bytes) Alternately you can load the packet as a pre-formatted text file. The text file should be one byte per line, beginning with a decimal value for the number of packets followed by hex values for the remaining bytes. Load the text file at the packet length prompt.
Optical Bypass Switch with Heartbeat To restore the bypass switch to factory defaults: 1. Type z and press Enter. You are prompted to select which type of packet you want to restore, IP or IPX. 2. Select 1 to restore defaults with an IP packet or 0 to restore defaults with an IPX packet.
Optical Bypass Switch with Heartbeat ® Network A B Monitor 1 Optical Bypass Switch 2 BYPASS ON OFF 2 ACT 1 OUT IN OUT IN OUT IN OUT IN LINK A B 1 2 LASER CAUTION! www.netoptics.com Rx Tx B A To Switch, Server, or Router To Switch, Server, or Router Figure 6: Connecting to the Network 3. Verify that the bypass switch Network Ports are cabled in-line between two devices.
Optical Bypass Switch with Heartbeat Connecting to the In-line Device To connect the bypass switch to the in-line device: 1. Connect Monitoring Port C to the in-line appliance using a duplex LC fiber cable. This acts as your DCE interface. 2. Connect Monitoring Port D to the in-line appliance using a duplex LC fiber cable. This acts as your DTE interface.
Optical Bypass Switch with Heartbeat Specifications Splitter Specifications Fiber Type: Multimode: Corning 50 or 62.5/125µm, wavelength, 850nm Insertion Loss: Network Port: ≤ 1.25 dB Monitor Port: ≤ 1.25 dB Fiber Type: Singlemode: Corning 8.5/125µm, wavelength, 1310nm Insertion Loss: Network Port: ≤ 1.25 dB Monitor Port: ≤ 1.25 dB Note:_________________________________________________________________ There is no insertion loss when the bypass switch is not receiving power.
Optical Bypass Switch with Heartbeat Limitations on Warranty and Liability Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC. BE LIABLE FOR ANY DAMAGES INCURRED BY THE USE OF THE PRODUCTS (INCLUDING BOTH HARDWARE AND SOFTWARE) DESCRIBED IN THIS MANUAL, OR BY ANY DEFECT OR INACCURACY IN THIS MANUAL ITSELF.
www.netoptics.com © 2010 by Net Optics, Inc. All Rights Reserved.
