User Guide for 4xN 10/100/1000 Span iMatrix Switch™ Model ISW-CU3-S4x16 Doc. PUB ISWCU3S4U Rev.
PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using a Net Optics Switch you agree to the terms and conditions of usage set forth by Net Optics, Inc. No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual property rights associated with the technology described in this manual. This manual is intended to assist with installing Net Optics products into your network. Trademarks and Copyrights © 2006 by Net Optics, Inc.
4xN 10/100/1000 Span Port iMatrix Switch Contents Chapter 1 Introduction Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xN 10/100/1000 Span Port iMatrix Switch Configuring the iMatrix Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Message Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Chapter 4 Using System Manager Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Installing System Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4xN 10/100/1000 Span Port iMatrix Switch Chapter 1 Introduction Overview Net Optics 4xN 10/100/1000 Span Port iMatrix Switches enhance LAN visibility by providing access across multiple 10/100/1000 Span ports for up to four analyzers or security devices. The physical layer connections through the iMatrix Switch eliminate the need to reconnect and reconfigure analyzers for each new monitoring task. This flexibility instantly improves ease of use and return on investment.
4xN 10/100/1000 Span Port iMatrix Switch Key Features Passive, Secure Technology • Provides complete cross-link visibility at 1000 Mbps without data stream interference or introducing a point of failure • Daisy Chain iMatrix Switches for doubled or tripled coverage • Redundant power ensures monitoring uptime • Fully RoHS compliant Ease of Use • Remote management software provides control over which links are being monitored • LED indicators on the iMatrix Switch allow for quick status checks • Front-mounte
4xN 10/100/1000 Span Port iMatrix Switch Unpacking and Inspection Carefully unpack the 10/100/1000 Span Port iMatrix Switch and check for damaged or missing parts.
4xN 10/100/1000 Span Port iMatrix Switch Product Diagrams Monitor Port LED Displays Power LEDs Span Port Connectors 1 2 3 5 6 7 4 9 10 11 12 13 14 15 16 2 1 Daisy Chain Monitor 1 Daisy Chain Monitor 2 Daisy Chain Monitor 3 Daisy Chain 4x16 10/100/1000 Span Port Switch Monitor 4 8 Monitor Ports Monitor Daisy Chain Ports Figure 1: Front Panel ISW-CU3-S4X16 Power Plug Power Plug Remote Interface Port CONTROL PORT 1 DIP Switch CONTROL PORT 2 1 2 3 4 5 6 7 8 OFF Daisy Chain C
4xN 10/100/1000 Span iMatrix Switch Chapter 2 Installing the iMatrix Switch Overview The procedure for installing the iMatrix Switch follows these basic steps: • • • • • • • • Plan the installation Configure IP parameters Mount the iMatrix Switch Connect the Management Port Connect to the network Connect to the monitoring devices Apply power to the iMatrix Switch Check the installation Installation Planning There are two methods for connecting your iMatrix Switch: Single iMatrix Switch Mode • A single mo
4xN 10/100/1000 Span iMatrix Switch Configuring the iMatrix Switch The iMatrix Switch is configured with default values that allow you to install the iMatrix Switch and then modify parameters from Web Manager or SNMP Manager. The defaults values are: IP Address: 10.60.0.123 Netmask: 255.255.0.0 Monitor Ports 1-4: Gigabit CLI username: netoptics CLI password: netoptics You can set all parameters, check status, and control Monitor Port connections from the Command Line Interface.
4xN 10/100/1000 Span iMatrix Switch DB9 Control Port 2 CONTROL PORT 1 CONTROL PORT 2 1 2 3 4 5 6 7 8 OFF To COM port on monitoring device or computer Figure 9: Connecting to the CLI 3. Launch your terminal emulation software and set the communication parameters to: 19200 baud 8 data bits No parity 1 stop bit No flow control 3. Connect power to the iMatrix Switch. The CLI banner and login prompt appears.
4xN 10/100/1000 Span iMatrix Switch 2. Change the password by typing the following command: set password where is your new password. 3. Record the username and password in a secure location. To set the iMatrix Switch IP address: 1. Type set ip where is the IP address you are assigning to the iMatrix Switch and press Enter. For example, typing set ip 10.60.0.100 sets the iMatrix Switch IP address to 10.60.0.100. To display current settings: 1.
4xN 10/100/1000 Span iMatrix Switch To use the Help command: 1. Type Help and press Enter at the NetOptics prompt. The list of help topics is displayed. NetOptics: help ************************************* * Net Optics Command Line Interface * ************************************* Usage: “help” : set - Configure various options. reset - Reset options. switch - Switch control commands. show - show current configuration and status. echo - Turn on or off echoing of characters.
4xN 10/100/1000 Span iMatrix Switch Connecting to Switch Span Ports 1. Connect Span Port 1 of the iMatrix Switch to the appropriate Span port on your switch using CAT5e straight-through cables. 2. Repeat Step 1 for each additional network switch Span port you wish to monitor.
4xN 10/100/1000 Span iMatrix Switch 2. Connect a CAT5e cable to the iMatrix Switch Monitor Port 1 and the input port of the monitoring device. 3. Repeat Step 3 above to connect Monitor Ports 2 through 4 of the iMatrix Switch to a monitoring device.
4xN 10/100/1000 Span iMatrix Switch Daisy Chaining iMatrix Switches You have the option of connecting as many as three switches together for control by a single monitoring device or computer. It does not matter if you are connecting the monitoring ports to one device or separate devices. In a daisy chain configuration, one iMatrix Switch serves as the Controller to one or two Client iMatrix Switches. The Controller/Client relationship is set with the DIP switches on the rear of the iMatrix Switch.
4xN 10/100/1000 Span iMatrix Switch 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 2 1 Daisy Chain Monitor 1 Daisy Chain Monitor 2 Daisy Chain Monitor 3 Daisy Chain 4x16 10/100/1000 Span Port Switch Monitor 4 iMatrix Switch Client 2 8 Client 2 DIP Switch Settings 1 2 3 4 5 6 7 8 OFF 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 2 1 Daisy Chain Monitor 1 Daisy Chain Monitor 2 Daisy Chain Monitor 3 Daisy Chain 4x16 10/100/1000 Span Port Switch Monitor 4 iMatrix Switch Client
4xN 10/100/1000 Span iMatrix Switch CONTROL PORT 1 CONTROL PORT 2 1 2 3 4 5 6 7 8 OFF CONTROL PORT 1 CONTROL PORT 2 1 2 3 4 5 6 7 8 OFF CONTROL PORT 1 CONTROL PORT 2 1 2 3 4 5 6 7 8 OFF Figure 10: Connecting the Daisy Chain Control Ports 5. Supply power to the iMatrix Switch using the power cords included with the unit. Verify that the Power LEDs illuminate.
4xN 10/100/1000 Span Port iMatrix Switch Chapter 3 Using iMatrix Switch Web Manager Overview This chapter describes how to monitor and control individual iMatrix Switches using Web Manager.
4xN 10/100/1000 Span Port iMatrix Switch Figure 11: Web Manager Page To save any changes to the iMatrix Switch, you must click Submit Changes. To update the display, click your browser's refresh button. Viewing Switch Status You can view iMatrix Switch information from the Switch Status section of Web Manager. The following table explains the status fields.
4xN 10/100/1000 Span Port iMatrix Switch Field Name Value Description Switch Hardware Version Displays the hardware version of the switch Switch Software Version Displays the software version of the switch Switch Control Web Manager lets you set which data port is connected to the Monitor Port. To change the network link you are monitoring, enter the number of the data port for the link and click Submit Changes.
4xN 10/100/1000 Span Port iMatrix Switch Message Board You can post a message about the iMatrix Switch in the Message Board text box. Anyone who open Web Manager for this iMatrix Switch will see your message. To enter a message, simple click in the text box and type your message.
4xN 10/100/1000 Span iMatrix Switch Chapter 4 Using System Manager Overview This chapter describes how to install and use Net Optics' System Manager, which allows you to change settings, view status, and retrieve data remotely from multiple Net Optics iMatrix Switch devices.
4xN 10/100/1000 Span iMatrix Switch 3. After reading the agreement, select I Agree and click Next to install System Manager. The Welcome dialog box appears as shown in Figure 13. Figure 13: Welcome Dialog Box 2. Click Next. The Select Installation Folder dialog box shown in Figure 14 appears.
4xN 10/100/1000 Span iMatrix Switch 3. To install in the default folder, make no changes to the path in the Folder: text box. To install in a different location, either type the path in the Folder: text box or click Browse to find another location. To check the space available for System Manager on the selected drive, click Disk Cost. 4. To limit access to System Manager to the current user of the PC, select Just Me. To allow access to any user logged into the PC, select Everyone. 5. Click Next.
4xN 10/100/1000 Span iMatrix Switch Figure 16: Installation Progress 6. If you want to stop the installation, click Cancel. When the installation is complete, the Installation Complete dialog box appears as shown in Figure 17. Figure 17: Installation Complete 7. Click Close. System Manager is now installed on your computer and there is a Net Optics shortcut icon on your desktop.
4xN 10/100/1000 Span iMatrix Switch Exploring System Manager This section explains the features and functions of System Manager.
4xN 10/100/1000 Span iMatrix Switch Tip! _____________________________________________________________________ To use pop-up menu shortcuts, click your right mouse button in the System Frame. __________________________________________________________________________ Using the Toolbar Figure 19 shows the System Manager toolbar. Figure 19: Toolbar The table below describes the headings found on the toolbar.
4xN 10/100/1000 Span iMatrix Switch Figure 21: Group Bar 2. Type the name of the new group and press Enter. Deleting a Group You can delete a group however, all iMatrix Switches in that group will also be deleted from System Manager. Note: ____________________________________________________________________ Deleting an iMatrix Switch from System Manager does not affect the current operating status of the iMatrix Switch.
4xN 10/100/1000 Span iMatrix Switch To add an iMatrix Switch to the system: 1. Select the Group to which you want to add an iMatrix Switch by clicking the group bar. 2. Click New Node in the toolbar as shown in Figure 22. The New Node dialog box appears as shown in Figure 23. Figure 22: Adding a New iMatrix Switch Figure 23: New iMatrix Switch 2. Enter a name for the iMatrix Switch you are adding in the Node Name text box. Each Node Name in the system must be unique. 3.
4xN 10/100/1000 Span iMatrix Switch Figure 24: Net Optics System Manager with an iMatrix Switch The indicator to the right of the iMatrix Switch picture blinks green when the iMatrix Switch is functioning normally. If there is an alarm condition on the iMatrix Switch, the indicator blinks red. If System Manager cannot communicate with the iMatrix Switch, the graphic of the switch appears grayed. Check that the iMatrix Switch is connected to the network and verify the configuration information. 7.
4xN 10/100/1000 Span iMatrix Switch Deleting an iMatrix Switch You can delete an iMatrix Switch from System Manager when you remove an iMatrix Switch from your network. If you have removed an iMatrix Switch from the network, System Manager continues to poll the iMatrix Switch’s IP address for data until you delete the iMatrix Switch from System Manager. To delete an iMatrix Switch from System Manager: 1. Select the iMatrix Switch you want to delete by clicking its icon. 2. Click Delete in the toolbar.
4xN 10/100/1000 Span iMatrix Switch 2. For the parameter you wish to configure, click on the corresponding value field. 3. Select an option from the drop-down list or enter a new value from your keyboard. 4. The new configuration parameters take effect next time System Manager polls the iMatrix Switch. The table below describes the configuration options on the Configure Tab. Host Name The name of the iMatrix Switch IP Address The IP address of the iMatrix Switch. Netmask The IP address netmask.
4xN 10/100/1000 Span iMatrix Switch Figure 27: iMatrix Switch Status Tab The Status tab is a read-only list of information from the iMatrix Switch. Use the scroll bar and arrows to view the entire list if necessary. TIP! _____________________________________________________________________ Fields that have been updated since the last refresh appear with a circle and arrow just to the left of the value field.
4xN 10/100/1000 Span iMatrix Switch Monitor Port 4 Data Port The Span Port currently connected to Monitor Port 4. To change the Monitor Port connection, use the Control Tab. Total Data Ports Total number of Data Ports on the iMatrix Switch including any ports on daisy-chained Client iMatrix Switches. Total Switches Total number of daisy-chained Client iMatrix Switches plus the Controller iMatrix Switch (1-3).
4xN 10/100/1000 Span iMatrix Switch Controlling Switch Connections Use the Control Tab to connect the Monitor Ports to a connected Span Port. You can connect four monitoring devices to any four Span Ports on the switch or daisy-chained switches. To connect a Monitor Port to a Span Port: 1. Click the Control tab. Figure 29 shows the Control Tab for a 2xN iMatrix Switch. The 4xN GigaBit Copper Span Switch will show four Monitor Port columns. Figure 29: Control Tab 2. Click a port in the Mon.
4xN 10/100/1000 Span iMatrix Switch Figure 30: Connecting Monitor Port 1 2. Click a port in the Mon. 2 column to connect the device on Monitor Port 2 to a Span Port. The example in Figure 31 shows Monitor Port 2 connected to Span Port 4. Figure 31: Connecting Monitor Port 2 3. Repeat for Steps 1 and 2 for Mon. 3 and Mon. 4 columns. You cannot connect more than one Monitor Port to a Span Port.
4xN 10/100/1000 Span iMatrix Switch 4. To clear all port connections, click Reset All. Entering Port Names and Notes You have the option of naming the Span Ports and entering a note. Naming the Span Ports will make switch management easier. Add notes to the Span Port connection to communicate important information to other users of System Manager. To enter Span Port Names and Notes: 1. Click the text box next to the Span Port number you wish to name. 2. Enter the name of the Span Port and press Enter. 3.
4xN 10/100/1000 Span iMatrix Switch Appendix A Specifications and Models Specifications Electrical Power Input 100-240VAC, 0.5A, 47-63Hz Environmental Operating Temperature 0˚C to 55˚C Storage Temperature -10˚C to 70˚C Relative Humidity 5% min, 95% max, non-condensing Mechanical Dimensions 1.75” high x 15.
4xN 10/100/1000 Span iMatrix Switch Software Command Line Interface Any terminal emulation software iMatrix Web Manager Any browser iMatrix System Manager Windows 98, Windows 2000, Windows XP Certifications Fully RoHS compliant 36
4xN 10/100/1000 Span iMatrix Switch Appendix B Command Line Interface Command Sub-Command Syntax Description Help Set help set Displays the set command options. Reset help reset Displays the reset command options. Show help show Displays the show command options. Echo help echo Displays the echo command options. Display help display Displays the display command options. IP set ip
Where is the IP address of the iMatrix Switch.4xN 10/100/1000 Span iMatrix Switch Command Sub-Command Syntax Description Switch Monitor Port switch monitor port Sets which data port is monitored where is 1, 2, 3, or 4 and is the data port number Show Set show set Displays currents settings. Switch show status Displays current data port connected to the monitor port. Display show display Displays the display setting. Display OFF disables remote interfaces.
4xN 10/100/1000 Span iMatrix Switch Notes: 39
www.netoptics.com © 2006 by Net Optics, Inc. All Rights Reserved.
