Owner's manual

ManualsBrandsNet Optics ManualsComputer Hardware10_100BaseT Multi-Station Tap

Installation Guide for

10/100BaseT Multi-Station Tap

Models TP4-CU, TP8-CU, TP12-CU, TP16-CU, TP20,CU

Doc. PUBTP4CUU Rev. 1, 06/06

Summary of content (16 pages)

PAGE 1
Installation Guide for 10/100BaseT Multi-Station Tap Models TP4-CU, TP8-CU, TP12-CU, TP16-CU, TP20,CU Doc. PUBTP4CUU Rev.
PAGE 2
PAGE 3
10/100 Multi-Station Tap Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
10/100 Multi-Station Tap PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using a Net Optics Tap you agree to the terms and conditions of usage set forth by Net Optics, Inc. No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual property rights associated with the technology described in this manual. This manual is intended to assist with installing Net Optics products into your network.
PAGE 5
10/100 Multi-Station Tap Introduction Net Optics 10/100BaseT Taps supply mission-critical networks with superior network visibility and security access. The breakthrough design of the Net Optics 10/100BaseT Tap ensures zero impact on network traffic while maintaining uninterrupted access for monitoring and security devices. These are the world’s first and only 10/100BaseT Taps offering “zero delay” technology.
PAGE 6
10/100 Multi-Station Tap Key Features Passive, Secure Technology • Provides passive access at speeds of 10 or 100 Mbps without data stream interference or introducing a point of failure • Unique Zero Delay technology ensures no packet delay or loss if power is lost to the Tap • Passes all full-duplex traffic (including errors) from all layers for comprehensive troubleshooting • No IP address is needed for the Tap or monitoring device, enhancing monitoring security • Redundant power ensures monitoring uptim
PAGE 7
10/100 Multi-Station Tap About This Guide Please read the guide before attempting to install 10/100 Multi-Station Tap. This guide covers the following models: Part Number Description TP4-CU 10/100BaseT 4 Station Tap TP8-CU 10/100BaseT 8 Station Tap TP12-CU 10/100BaseT 12 Station Tap TP16-CU 10/100BaseT 16 Station Tap TP20-CU 10/100BaseT 20 Station Tap Unpacking and Inspection Carefully unpack the 10/100 Multi-Station Tap and check for damaged or missing parts.
PAGE 8
10/100 Multi-Station Tap Product Diagrams 4 Port 10/100 Ethernet Tap A Network 1 B A Network 2 A B B A B Network 3 A B A B Network 4 A B A B PWR 2 ® PWR 1 Network Network Monitor Network Monitor Network Monitor Monitor www.netoptics.
PAGE 9
10/100 Multi-Station Tap Mounting Brackets (removable ears) 1 ® 2 1 3 2 4 5 7 6 8 9 10 Monitor 11 12 13 14 15 16 17 A A A A A B B B B B 18 19 20 High Density Tap 10/100 Ethernet Power LEDs Rubber Feet (removable) Monitor Ports Figure 6: TP12-CU Front Panel 20 19 18 17 16 15 14 13 12 A A A B B B 10 11 8 9 7 6 5 4 A A B B 3 2 1 Network Ports Network Ports Power Plugs Figure 7: TP12-CU Rear Panel Mounting Brackets (removable ears) 1 ® 2 1
PAGE 10
/100 Multi-Station Tap Cabling Guidelines • If connecting to Switches or Hubs, use CAT5 RJ45 cross-over cabling. • If connecting to Routers or NICs, use CAT5 RJ45 straight-through cabling. Connecting to the Network 1. Connect Network Port A to the appropriate switch, server or router using a CAT5 cable. 2. Connect Network Port B to the appropriate switch, server or router using a CAT5 cable.
PAGE 11
10/100 Multi-Station Tap Connecting to the Monitoring Device 1. Supply power to the Tap using the two redundant power supplies included with the unit. Verify that the Power LED illuminates. 2. Connect Monitor Port A to the appropriate port on the monitoring device using a CAT5 straight-through cable. 3. Connect Monitor Port B to the appropriate port on the monitoring device using a CAT5 straight-through cable.
PAGE 12
10/100 Multi-Station Tap Specifications Environment Operating Temperature: 0˚C to 40˚C Operating Temperature: -10˚C to 70˚C Relative Humidity: 10% min, 95% max, non-condensing Power Power Supply Input: 100-240VAC, 0.5A, 47-63Hz Output: 12V 1.5A -48V Power Supply Input: -48V DC typical, -36V DC min, -75V DC max Mechanical Dimensions: 1.75” high x 3” deep x 16.
PAGE 13
10/100 Multi-Station Tap Connectors TP4-CU model: (8) RJ45, 8-pin connectors (monitor ports) (8) RJ45, 8-pin connectors (network ports) TP8-CU model: (16) RJ45, 8-pin connectors (monitor ports) (16) RJ45, 8-pin connectors (network ports) TP12-CU model: (24) RJ45, 8-pin connectors (monitor ports) (24) RJ45, 8-pin connectors (network ports) TP16-CU model: (32) RJ45, 8-pin connectors (monitor ports) (32) RJ45, 8-pin connectors (network ports) TP20-CU model: (40) RJ45, 8-pin connectors (monitor ports) (40) RJ4
PAGE 14
10/100 Multi-Station Tap Limitations on Warranty and Liability Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC. BE LIABLE FOR ANY DAMAGES INCURRED BY THE USE OF THE PRODUCTS (INCLUDING BOTH HARDWARE AND SOFTWARE) DESCRIBED IN THIS MANUAL, OR BY ANY DEFECT OR INACCURACY IN THIS MANUAL ITSELF.
PAGE 15