Bypass Switch Installation Guide

ManualsBrandsNet Optics ManualsSwitch10/100/1000

Installation Guide for

10/100/1000 Bypass Switch

Model 96475 & 96476

Doc. IGNET96475/76 Revised 07/05

Summary of content (10 pages)

PAGE 1
Installation Guide for 10/100/1000 Bypass Switch Model 96475 & 96476 Doc.
PAGE 2
Installation Guide for 10/100/1000 Bypass Switch Table of Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
Installation Guide for 10/100/1000 Bypass Switch PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using a Net Optics 10/100/1000 Bypass Switch you agree to the terms and conditions of usage set forth by Net Optics, Inc.. . No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual property rights associated with the technology described in this manual.
PAGE 4
Installation Guide for 10/100/1000 Bypass Switch Introduction Net Optics GigaBit Bypass Switches provide a permanent and trouble-free access port for in-line network security and monitoring devices. The GigaBit Bypass Switch automatically switches network traffic through added in-line devices or bypasses devices that are about to be removed. Prevent link failure when attached IPS and IDS devices lose power by powering the Bypass Switch and in-line device from the same power source.
PAGE 5
Installation Guide for 10/100/1000 Bypass Switch Key Features (continued) Ease of Use • Silk-screened application diagram illustrates all connections for easy deployment • Optional 19-inch rack frames holds two Taps • Tested and compatible with all major manufacturers’ monitoring devices, including protocol analyzers, probes, and intrusion detection/prevention systems Support • Net Optics offers free technical support throughout the lifetime of your purchase.
PAGE 6
Installation Guide for 10/100/1000 Bypass Switch Connecting the 10/100/1000 Bypass Switch to the Network 1. Unpack the Bypass Switch, and obtain the required cables needed to successfully install the unit. 2. Connect Network Port A to the appropriate switch, server or router device. This will act as your DCE Interface. 3. Connect Network Port B to the appropriate switch, server or router device. This will act as your DTE interface. 4.
PAGE 7
Installation Guide for 10/100/1000 Bypass Switch Connecting the 10/100/1000 Bypass Switch 1 Connect Copper In-Line Ports CAT5 RJ45 Cable CAT5 RJ45 Cable Rack-Mount Frame Holds 2 Switches A ® To switch, server, or router (DCE) Y S A Bypass Switch 10/100 B Network 96475 IS C B Monitor Network A ® B x 3 x 4 x 5 6 Monitor www.netoptics.
PAGE 8
Installation Guide for 10/100/1000 Bypass Switch Specifications Operating Specifications: Operating Temperature: 0˚C to 55˚C Storage Temperature: -10˚C to 70˚C Relative Humidity: 10% min, 95% max, non condensing Mechanical Specifications: Power Supply: Input Power: 100-240V, 0.5A, 47-63Hz Output Power: 5V, 2.4A Dimensions: 1.125” high x 4.2” deep x 4.
PAGE 9
Installation Guide for 10/100/1000 Bypass Switch Limitations on Warranty and Liability Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC. BE LIABLE FOR ANY DAMAGES INCURRED BY THE USE OF THE PRODUCTS (INCLUDING BOTH HARDWARE AND SOFTWARE) DESCRIBED IN THIS MANUAL, OR BY ANY DEFECT OR INACCURACY IN THIS MANUAL ITSELF.