User Manual

INSTALLATION AND
OPERATING
INSTRUCTIONS
INFRARED DIGITAL
REMOTE CONTROL
BXERCIRDIMHA
BXERCIRDIMHGA
PACK CONTAINS
x2 x2
x1
x2
x1
ScrewsAnchors
Wall mount
Baeries 1.5V LR6
Remote control
FIRST COMMISSIONING
Pull on the sucon located
at the back of the remote
control.
Ambient temperature is dis
-
played, the remote control
is on.
INSTALLING THE
REMOTE CONTROL
WALL MOUNTING
OPERATING
USING
OVERVIEW
Note: the buons , , and have the same features
as the buons on the heang appliance to be remotely controlled.
Please refer to its user guide.
REPLACING BATTERIES
2 baeries 1.5V LR06 are located in the compartment at the back of
the remote control. Baery life of 2 years, it varies according to the
mode of use.
They must be replaced by 1.5V LR06 baeries, Alcaline only.
Remember to take used baeries to baery collecon points
so they can be recycled.
1- Unscrew the baeries cover
located at the back of the
remote control.
2- Remove the old baeries
and insert the new baeries
in the remote control.Please
check polarity of baeries
before inseron.
3- Put back the baeries cover
and screw back on the remote
control.
Pressing a key on the keypad has no eect:
- Change the 2 baeries.
- Check there is no obstacle between the remote control and the in
-
frared receiver to disturb the transmission.
- Posion the remote control toward the infrared receiver
(see Using).
- Bring the remote control closer to the infrared receiver.
General specicaons
-Power supply 2 alkaline baeries LR6 1.5V
-Typical lifeme: 2 years
- Adjustment of the seng temperature from +10°C to +30°C around
-Emission range: around 3 meters
Environment
-IP20
-Operang temperature: 0°C to 50°C
-Storage temperature: -10°C to +70°C
-Humidity: 90% to +40°C (without condensaon)
Manufactured by:
IMHOTEP créaon (contact@imhotepcreaon.com).
Compliance statement:
We hereby declare under our sole responsibility that the products des
-
cribed in these instrucons comply with the provisions of Direcves
and harmonized standards listed below:
- EMC 2014/30/EU: EN60730-1/ EN60730-2-9
and are manufactured using processes which are cered ISO 9001
V2015.
The symbol
axed on the product indicates that you must dis-
pose of it at the end of its useful life at a special recycling point, in ac-
cordance with European Direcve WEEE 2012/19/EU. If you are repla-
cing it, you can also return it to the retailer from which you buy the
replacement equipment. Thus, it is not ordinary household waste. Re
-
cycling products enables us to protect the environment and to use less
natural resources.
TECHNICAL
SPECIFICATIONS
TROUBLESHOOTING
ENG
Boost: acvaon of the boost
Display of the ambient temperature
Adjustment of the seng temperature
desired and the boost duraon
Selecon of the Auto, Comfort, Eco, Frost
protecon modes
2- Slide the remote control in
the base.
1- Fix the base into the wall
(centre distance of 57mm).
57mm
Posion the remote control towards the infrared receiving window of
the device.
Check that there is no obs
-
tacle between the remote
control and the infrared re
-
ceiver to disturb the trans-
mission.
infrared
receiving
window
- RoHS 2011/65/EU, amended by Direcves 2015/863/EU and
2017/2102/EU :
EN IEC 63000:2018