Data Sheet

CANADA (ISED) REGULATORY APPROVAL
The MM002-LS-US module has been certified for use in Canada under Industry Canada (IC) Radio Standards
Specification (RSS) RSS-247 and RSS-Gen. Modular approval permits the installation of a module in a host
device without the need to recertify the device.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This
device may not cause interference. 2. This device must accept any interference, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : 1.L’appareil ne doit pas produire de brouillage;
2.L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This radio transmitter (22302-MM002xUS) has been approved by Industry Canada to operate with the antenna
types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (22302-MM002xUS) a été approuvé par Industrie Canada pour fonctionner avec les
types d'antenne énumérés ci
‑ dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans
cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
The module is for use with external antenna ONLY. The certified antennas include:
- Dipole Antenna with maximum gain 2.2dBi.
LABELING AND USER INFORMATION REQUIREMENTS
The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host
device, otherwise the host device must be labeled to display the Industry Canada certification number of the
module, preceded by the words “Contains transmitter module”, or the word “Contains”, or similar wording
expressing the same meaning, as follows:
Contains Transmitter Module IC: 22302-MM002XUS
or
Contains IC ID: 22302-MM002XUS
User manuals for license-exempt radio apparatus shall contain the following or equivalent notice in a conspicuous
location in the user manual or alternatively on the device or both:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
RF EXPOSURE
All transmitters regulated by IC must comply with RF exposure requirements listed in RSS-102 - Radio Frequency
(RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands).
The following statement must be included as a caution statement in manuals and OEM products to alert users of
IC RF exposure compliance:
To satisfy IC RF Exposure requirements for mobile and base station transmission devices, a separation distance
of 20 cm or more should be maintained between the antenna of this device and persons during operation. To
ensure compliance, operation at closer than this distance is not recommended.
The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
If the MM002-L-US module is used in a portable application (i.e., the antenna is less than 20 cm from persons
during operation), the integrator is responsible for performing Specific Absorption Rate (SAR) exclusion
evaluation or testing in accordance with RSS-102.