GAS HOB THIS COOKTOP IS APPROVED FOR USE WITH NATURAL GAS AND UNIVERSAL LPG. LEAVE THESE INSTRUCTIONS WITH THE OWNER.
en Table of contents [ en] I NSTRUCTI ON MANUAL 8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ( Important safety information . . . . . . . . . . . . . . . 4 What to do if you smell gas . . . . . . . . . . . . . . . . . . . . . 4 5 Installation and connection. . . . . . . . . . . . . . . . . 5 Statutory requirements . . . . . . . . . . . . . . . . . . Preparing to install . . . . . . . . . . . . . . . . . . . . . Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended use 8Intended use Read these instructions carefully. You will only be able to use your appliance safely and effectively when you have read them. These operating and installation instructions should be retained, and passed onto the buyer if the appliance is sold. Removal of transit protection Packaging materials of the product are manufactured from recyclable materials. Do not dispose of the packaging materials together with the domestic or other wastes.
en Important safety information (Important safety information DO NOT MODIFY THIS APPLIANCE. DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE APPLIANCE STORAGE DRAWER OR NEAR THE APPLIANCE. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION. DO NOT USE THIS APPLAINCE AS A SPACE HEATER. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
Installation and connection 5Installation and connection I n s t a l a t i on a n d c o n e c t i o n Statutory requirements This installation must conform with the following: ■ Manufacturer’s Installation instructions ■ Local Gas Fitting Regulations ■ Municipal Building Codes ■ Refer to AS/NZS 5601.1 for Gas Installations ■ S.A.A. Wiring Code ■ Local Electrical Regulations ■ Any other statutory regulations en Preparing to install Refer to AS/NZS 5601.1 for piping size details.
en Installation and connection Clearances A range hood fitted above the top must be installed according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan. Any adjoining wall surface situated within 200 mm from the edge of any hob burner must be a suitable noncombustible material for a height of 150 mm for the entire length of the hob.
Installation and connection ■ This appliance must be earthed. When connecting the cooktop ensure that the earth wire is connected first and that all wires are connected to the correct terminals. en Fit regulator (N.G.) or a test point (Universal LPG) directly to the R 1/2’’ connection. 9 9 a / 1 9 9 Wiring diagram Direction of gas flow is indicated on the rear of the regulator.
en Installation and connection Ignite all burners both individually and concurrently to ensure correct operation of gas valves, burners and ignition. Turn gas taps to low flame position and observe stability of the flame for each burner individually and all together. Adhere the duplicate data plate to an accessible location near the hotplate. When satisfied with the hotplate, please instruct the user on the correct method of operation.
Getting to know your appliance Adjusting the bypass If necessary, use a Torx screwdriver to adjust the bypass screws (M): A: For ULPG the bypass screws must be tightened properly. B: For Natural Gas the bypass screws must finish flush with the fitting.
en Getting to know your appliance For dual-wok burners, the inner and outer flames can be controlled separately. The available power levels are as follows: k Inner and outer flame on full power. k kk k kk k k k k k k k Outer flame on low power, inner flame on full power. k kk k kk k k k k k k Inner flame on full power. k Residual heat indicator Every burner on the hob has a residual heat indicator that indicates whether it is hot or warm.
Gas burners ÄGas burners Gas bur ner s Switching on manually 1. Press the control knob for the selected burner and en An orange-coloured flame is normal. This is caused by the presence of dust in the atmosphere, spilt liquids, etc. In the event of the burner flames being accidentally extinguished, turn off the burner control and do not attempt to re-ignite the burner for at least one minute. turn it anticlockwise to the highest power setting. 2.
en Settings table and tips Place the pans on the pan supports, never directly on the burner. Make sure that the pan supports and burner caps are correctly positioned before using the appliance. Pans should be placed on the hob carefully. Do not strike the hob and do not place excessive weight on it. Do not place anything, eg. flame tamer, asbestos mat, between pan and pan support as serious damage to the appliance may result.
Settings table and tips Food Burner Pasta and rice Spaghetti High-output burner Standard-output burner Dual wok burner Rice High-output burner Standard-output burner Dual wok burner Ravioli High-output burner Standard-output burner Dual wok burner Total Step 1 time in ˜ § v min.
en Settings table and tips Food Burner High-output burner Dual wok burner Carbonara sauce Standard-output burner High-output burner Dual wok burner Fish Breaded hake High-output burner Standard-output burner Dual wok burner Baked salmon High-output burner Standard-output burner Dual wok burner Mussels High-output burner Dual wok burner Standard-output burner Total Step 1 time in ˜ § v min.
Settings table and tips Food Burner High-output burner Total Step 1 Step 2 time in ˜ § v ˜ § v min.
en Cleaning and maintenance 2Cleaning and maintenance Cl eani ng and mai nt enance Cleaning Once the appliance is cool, use a sponge to clean it with soap and water. After each use, clean the surface of the respective burner parts once they have cooled down. If any residue is left (baked-on food, drops of grease etc.), however little, it will become stuck to the surface and more difficult to remove later. The holes and grooves must be clean for the flame to ignite properly.
Trouble shooting en 3Trouble shooting DO NOT MODIFY THIS APPLIANCE. Only authorized personnel from the Service Centre are qualified to work on the appliance. Sometimes certain faults detected can be easily resolved. Before calling the Technical Assistance Service, bear in mind the following advice: Tr oubl e sho t i ng Fault Electrical operation is generally impaired. Possible cause Defective circuit breaker. Remedial action Check inside the fuse box to see if any of the fuses are damaged.
en Customer service 4Customer service When contacting our customer service, please provide the product number (E-Nr.) and production number (FD) of the appliance. This information is given on the specifications plate located on the lower section of the hob and on the label in the user manual. After-sales contact details for all countries can be found in the attached after-sales service directory.
*9001250924* 9001250924 001214(C) en
