Dishwasher [en] User manual S155HVX15G
en Table of contents Safety ............................................... 4 General information.......................... 4 Intended use..................................... 4 Restriction on user group................. 4 Safe installation ................................ 5 Safe use ........................................... 6 Damaged appliance ......................... 7 Risk to children ................................ 8 Preventing material damage ........ 10 Safe installation .........................
en Terminate programme.................... 32 Switching off appliance .................. 33 Basic settings................................ 34 Overview of basic settings ............. 34 Changing basic settings................. 35 Home Connect .............................. 36 Home Connect quick start ............. 36 Home Connect settings.................. 37 Remote Start ............................... 37 Remote Diagnostics ...................... 37 Software update .............................
en Safety Safety Please read the safety information to ensure that you use the appliance safely. General information ¡ Read this instruction manual carefully. Only this will ensure you use the appliance safely and efficiently. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Check the appliance after unpacking it. Do not connect the appliance if it has been damaged in transit.
Safety en Safe installation Follow these safety instructions when installing the appliance. WARNING ‒ Risk of injury! Improper installation may cause injury. ▶ When installing and connecting the appliance, follow the instructions in the manual and installation instructions. WARNING ‒ Risk of electric shock! ¡ Improper installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate.
en Safety ▶ Only use adapters approved by the manufacturer. WARNING ‒ Risk of injury! Hinges move when opening and closing the appliance door and can cause injury. ▶ If built-under or integrable appliances are not in a cavity so that one side is accessible, the hinge area must be covered at the side. Covers are available from Customer Service or specialist outlets. WARNING ‒ Risk of tipping! Improper installation may cause the appliance to tip up.
Safety en WARNING ‒ Risk of injury! ¡ Leaving the appliance door open may result in injury. ▶ Only open the appliance door to load or unload tableware in order to prevent accidents, e.g. through tripping. ▶ Do not sit or stand on the appliance door when open. ¡ Knives and utensils with sharp points can cause injuries. ▶ Arrange knives and utensils with sharp points in the cutlery basket with the points downwards, on the knife shelf or in the cutlery drawer.
en Safety ▶ Never operate an appliance with a cracked or fractured surface. ▶ Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains. ▶ If the appliance or the power cord is damaged, immediately unplug the power cord or switch off the fuse in the fuse box and turn off the water tap. ▶ "Call Customer Service." → Page 55 ▶ Repairs to the appliance should only be carried out by trained specialist staff. ¡ Incorrect repairs are dangerous.
Safety en WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. ▶ With redundant appliances, unplug the power cord. Then cut through the cord and damage the lock on the appliance door beyond repair so that the appliance door will no longer close. WARNING ‒ Risk of crushing! With higher-level appliances, children can become crushed between the appliance door and cabinet doors underneath.
en Preventing material damage Preventing material damage Preventing material damage Preventing material damage Safe installation Follow the instructions when installing the appliance. ATTENTION! ¡ Improper installation of the appliance may cause damage. ▶ If the dishwasher is installed above or below other domestic appliances, follow the information on installation in combination with a dishwasher in the installation instructions for the individual appliances.
Environmental protection and saving energy ▶ So as not to scratch the finish on the appliance, do not use sponges with a rough surface or abrasive cleaning agents. ▶ To prevent corrosion, do not use sponge cloths on dishwashers with a stainless steel front or rinse such cloths thoroughly several times before using them for the first time. en and replaced with fresh water. If the soiling level is lower, the rinsing water is used in the next wash cycle, so reducing water consumption by 3-6 litres.
en Installation and connection over, e.g. by screwing it to the wall or installing it under a continuous worktop that is securely connected to adjacent cabinets. 1. "Follow the safety instructions." → Page 4 2. "Follow the instructions for electrical connection." → Page 12 3. Check the Scope of supply and the condition of the appliance. 4. Consult the installation instructions for the installation dimensions required. 5. Make the appliance level using the height-adjustable feet.
Installation and connection en The connection data for the appliance can be found on the rating plate. 3. Check that the mains plug is inserted properly.
en Familiarising yourself with your appliance Familiarising yourself with your appliance Familiarising yourself with your appliance Familiarising yourself with your appliance Appliance You can find an overview of the parts of your appliance here. 8 7 9 6 10 5 4 11 3 12 2 1 1 1 14 Rating plate Depending on the appliance specifications Rating plate with "E number and FD number" → Page 56. The data you need for "Customer Service" → Page 55.
Familiarising yourself with your appliance 2 Detergent dispenser 3 4 Bottom basket 5 Lower spray arm 6 Tablet collecting tray Dispenser for special salt 7 8 9 10 Top basket 11 12 Filter system 1 Cutlery drawer 1 en "Detergent" → Page 27 is added to the detergent dispenser. "Bottom basket" → Page 20 Add the special salt to the dispenser for special salt. → "Water softening system", Page 23 The lower spray arm washes the tableware in the bottom basket.
en Familiarising yourself with your appliance 1 2 3 4 5 6 13 12 7 8 11 10 9 1 ON/OFF button 2 3 4 5 6 7 Programme buttons "Switching on the appliance" → Page 31 "Switching off the appliance" → Page 33 "Terminating the programme" → Page 32 "Programmes" → Page 17 Special salt refill indicator "Water softening system" → Page 23 Rinse aid refill indicator "Rinse aid system" → Page 26 WLAN display "Home Connect" → Page 36 Water supply display Display for water supply Programme buttons and a
Programmes en Programmes Programmes You can find an overview of the programmes that can be selected here. Different programmes, which can be found on the control panel of your appliance, are available depending on the appliance configuration. The running time may vary depending on the programme selected. The running time depends on the water temperature, the quantity of tableware, the level of soiling and the additional function selected.
en Programmes Programme Glass 40° Classic 60° Easy Clean Use Programme sequence Tableware: ¡ Cleaning delicate tableware, cutlery, temperature-sensitive plastics, glasses and stemware in the stemware basket. Level of soiling: ¡ Removing lightly adhering fresh food remnants. Tableware: ¡ Cleaning mixed tableware and cutlery. Level of soiling: ¡ Removing common household food remnants lightly dried-on. Only when using unloaded appliance.
Additional functions 2. Press . 3. Press the right programme button. Additional func- Use tion ¡ Switch on with mixed loads containing tablePower Zone ware with different soiling levels, e.g. place very soiled pots and pans in the bottom basket and normally soiled tableware in the upper basket. ¡ The spray pressure in the bottom basket is increased and the maximum programme temperature held longer. This will increase the run time and energy consumption.
en Features Top basket Arrange cups and glasses in the top basket. You can adjust the height of the top basket to make room for larger items of tableware. Adjusting top basket with side levers To wash large items of tableware in the baskets, adjust the shelf position of the top basket. 1. Pull out the top basket. 2. To prevent the basket from suddenly dropping down, hold the side of the basket by the top edge. 3. Press in the levers on the right and left on the outside of the basket. 4.
Features en Etagere Use the cutlery shelf and space underneath for small cups and glasses or for large items of cutlery, e.g. cooking spoons or serving cutlery. Cutlery drawer Arrange cutlery in the cutlery drawer. If you do not need the cutlery shelf, you can fold it up. Folding prongs Use the folding prongs to position tableware securely, e.g. plates. Arrange cutlery with the points and sharp edges downwards. You can fold the prongs down to position pans, bowls and glasses better.
en Features 1. Push the lever forwards down the prongs and fold . 1 2 Note: Check that the appliance is always operated with the top basket or the baking sheet spray head. Inserting baking sheet spray head Use the baking sheet spray head instead of the top basket to clean large trays, grilles and plates. 1. Remove top basket. 2. Insert the baking sheet spray head in the holder and turn to the right . 2. To use the prongs again, fold them back up. a The prongs audibly click into position.
Before using for the first time Setting 2 max. ø 3 max. ø Top basket 18.5 cm 21 cm Before using for the first time Before using for the first time Configure the settings for initial startup. Before using for the first time Bottom basket 27.5 cm 25 cm 5. "Set the amount of rinse aid to be dispensed." → Page 26 6. "Add detergent" → Page 27. 7. Start the Programme with the highest cleaning temperature without tableware.
en Water softening system Water hardness °E 13 - 15 16 - 20 21 - 26 27 - 38 39 - 62 Hardness range Medium Medium Hard Hard Hard Note: Set the water hardness determined on your appliance. → "Setting the water softening system", Page 24 With a water hardness of 0 - 8 °E you can dispense with special salt and switch off the water softening system. → "Switching off the water softening system", Page 25 Setting the water softening system Set the water hardness on your appliance. 1.
Water softening system 3. Note: Only use special salt for dishwashers. Do not use salt tablets. Do not use table salt. Add the special salt to the dispenser. a Funnel 1 Fill the dispenser right up with special salt. The water in the dispenser is displaced and forced out. 4. Place the lid back on the dispenser and turn to close. Switching off the water softening system If you find the special salt refill indicator irritating, e.g.
en Rinse aid system Additional water consumption in litres Additional power consumption in kWh 5 2. Add rinse aid up to the max mark. 0.05 The consumption values specified are laboratory measurements determined in accordance with the currently applicable standard and using the Eco 50° programme and the factory value of the water hardness is set to 16 - 20°E. max 3.
Detergent 5. To save the settings, press for 3 seconds. Switching the rinse aid system off If you find the rinse aid refill indicator irritating, e.g. when using combined detergents with a rinse aid component, you can switch the rinse aid system off. Tip: The function of rinse aid is limited with combined detergents. You will generally get better results using rinse aid. 1. Press . 2. To open the basic settings, press for 3 seconds. a The display shows Hxx. a The display shows . 3.
en Detergent Tip: Suitable detergents are available online via our website or from "Customer Service" → Page 55. Separate detergents Separate detergents are products that do not contain components other than detergent, e.g. powder detergent or liquid detergent. With powder and liquid detergent the dosage can be individually adjusted to the level of soiling of the tableware.
Tableware ¡ The function of rinse aid is limited with combined detergents. You will generally get better results using rinse aid. ¡ Use tablets with a special drying performance. en 3. Close the lid of the detergent dis- penser. Adding detergent 1. To open the detergent dispenser, press the locking latch. 2. Add the detergent to the dry deter- gent dispenser. 50 ml 25 ml 15 ml If you are using tablets, one is enough. Insert the tablets in a horizontal position.
en Tableware Damage to glass and tableware Avoid damage to glass and tableware. Cause The following tableware is not dishwasher-safe: ¡ Items of cutlery and tableware made from wood ¡ Decorated glassware, antique and hand-crafted tableware ¡ Plastic parts not resistant to heat ¡ Tableware made from copper or tin ¡ Tableware soiled with ash, wax, lubricating grease or paint ¡ Very small items of tableware Glass and tableware was not dishwashersafe. The chemical composition of the detergent causes damage.
Basic operation To save resources, do not prerinse tableware under running water. 2. Observe the following when arranging tableware: – Put heavily soiled tableware in the bottom basket, e.g. pans. The more powerful the spray jet, the better the dishwashing result will be. – To prevent damage to tableware, arrange it so it is stable and cannot tip over. – To prevent injury, arrange cutlery with the points and sharp edges downwards.
en Basic operation Setting a programme Starting the programme To adjust the wash cycle to the soiling level of the tableware, select a suitable programme. ▶ Press the right programme button. → "Programmes", Page 17 a The programme is set and the programme button flashes. a The remaining running time of the programme appears on the display. ▶ Press . a The programme has ended when the display shows "0h:00m".
Basic operation en 2. Press for approx. 4 seconds. 3. Close the appliance door. a All displays light up. a As soon as the displays are off, the display shows "0h:01m" and the residual water is pumped out. a The programme is cancelled and ends after approx. 1 minute. Switching off appliance 1. Please note the information on "Safe use" → Page 10. . 2. Press Tip: If you press during the wash cycle, the programme currently running will be interrupted.
en Basic settings Basic settings Basic settings You can configure the appliance to meet your needs. Basic settings Overview of basic settings The basic settings depend on the features of your appliance. Basic setting Water hardness Display text H04 1 Rinse aid dispensing r05 Intensive drying d00 1 d00 - d01 Hot water A00 1 A00 - A01 1 34 1 Selection H00 - H07 r00 - r06 Factory setting (may vary according to model) Description Set the water softening system to your water hardness.
Basic settings en Basic setting InfoLight Display text I01 1 Selection I00 - I01 Tone volume b02 1 b00 - b03 Wi-Fi Cn0 1 Cn0 - Cn1 Remote Start rc11 rc0 - rc2 Factory setting rE Start with YES Confirm with 1 Description Switch InfoLight on or off. While the programme is running, a spot of light is projected onto the floor below the appliance door. This light will not be visible if the appliance is installed at eye level with the cabinet front fitted flush.
en Home Connect 6. To save the settings, press for 3 seconds. 7. Close the appliance door. Home Connect Home Connect This appliance is network-capable. Connect your appliance to a mobile device to control its functions via the Home Connect app. The Home Connect services are not available in every country. The availability of the Home Connect function depends on the availability of Home Connect services in your country. You can find information about this at: www.home-connect.com.
Home Connect Home Connect settings Adapt Home Connect to your needs. You can find the Home Connect settings in the basic settings for your appliance. Which settings the display shows will depend on whether Home Connect has been set up and whether the appliance is connected to your home network. Remote Start You can use the Home Connect app to start the appliance with your mobile device.
en Cleaning and servicing Note: Please note that the Home Connect functions can only be utilised with the Home Connect app. Information on data protection can be retrieved in the Home Connect app. Cleaning and servicing Cleaning and servicing To keep your appliance working efficiently for a long time, it is important to clean and maintain it carefully. Cleaning and servicing Cleaning the tub WARNING Risk of harm to health! Using detergents containing chlorine may result in harm to health.
Cleaning and servicing Phase 2 Removal of Food remnants and deposits Detergent Machine cleaner To ensure optimum cleaning performance, the programme doses the detergents independently of each another during the relevant cleaning phase. Correct placement of the detergents is necessary here. Run Easy Clean without tableware if the indicator for Easy Clean lights up on the control panel or if advised to do so by the display. The indicator will go out after you have run Easy Clean.
en Cleaning and servicing Cleaning filters Soiling in the dishwashing water may block the filters. 1. After each wash check the filters for residue. 2. Turn the coarse filter anticlockwise and remove the filter system . ‒ Check that no foreign objects fall into the sump. 4. Press the locking catches together and lift the coarse filter out . 2 1 2 5. Clean the filter elements under run- 1 3. Pull down the micro filter to re- move. 40 ning water.
Cleaning and servicing en Cleaning spray arms Limescale and soiling in the dishwashing water may block the nozzles and bearings on the spray arms. Clean the spray arms regularly. 1. Unscrew the upper spray arm and pull down to remove . 1 2 2. Pull up the lower spray arm to re- move. 3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies. 4. Insert the lower spray arm. a The spray arm clicks into position. 5.
en Troubleshooting Troubleshooting Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshooting information before contacting after-sales service. This will avoid unnecessary costs. Troubleshooting WARNING Risk of electric shock! Incorrect repairs are dangerous. ▶ Repairs to the appliance should only be carried out by trained specialist staff. ▶ Only use genuine spare parts when repairing the appliance.
Troubleshooting Fault E:32-00 will light up alternately or indicator for water supply lights up. Cause en Troubleshooting 4. Unscrew the water connection. 5. Remove the filter from the supply hose 6. Clean the filter. 7. Re-insert the filter in the supply hose. 8. Screw the water connection back on. 9. Check the water connection for leaks. 10. Restore the power supply. 11. Switch the appliance on. E:92-40 will light up alternately. Filters are soiled or blocked. ▶ Clean the filters.
en Troubleshooting Fault E:90-01 will light up alternately. Cause Mains voltage is too low. A different error code apA technical fault is present. pears in the display window. E:01-00 to E:90-10 Troubleshooting This is not a fault on the appliance. 1. Contact an electrician. 2. Have the mains voltage and electrical installation checked by an electrician. 1. Press . 2. Unplug the appliance or switch off the fuse. 3. Wait at least 2 minutes. 4.
Troubleshooting Fault Tableware is not dry. en Cause Troubleshooting Water collects in recesses of ▶ Position tableware at an angle the tableware or cutlery. where possible. The combined detergent used has a poor drying performance. 1. Use rinse aid to improve drying per- formance. 2. Use a different combined detergent with a better drying performance. Extra Dry not activated to im- ▶ Activate Extra Dry. prove drying performance. Tableware removed too 1. Wait until the programme ends.
en Troubleshooting Fault Remnants of food on tableware. Cause Tableware is placed too close together or basket is overfilled. Troubleshooting 1. Arrange tableware with sufficient space in between. The spray jets must reach the surfaces of the tableware. 2. Avoid points of contact. Spray arm rotation is blocked. ▶ Arrange tableware so that it does Spray arm nozzles are blocked. Filters are soiled. ▶ Clean the "Spray arms" → Page 41. Filters are inserted incorrectly and/or not engaged. 1.
Troubleshooting Fault Detergent residue in the appliance Water marks on plastic parts. Cause Tabs are used in the quick or short programme. Dissolving time of the tab is not attained. Washing effect and dissolving performance are reduced after a prolonged storage time or detergent is very lumpy. Due to laws of physics droplet formation on plastic surfaces is unavoidable. After drying water marks are visible.
en Troubleshooting Fault Cause Stubborn white coatings are Too little detergent is being present on tableware, inside used. the appliance or the door. Washing programme selected too weak. Tea residue or lipstick marks Washing temperature is too on tableware. low. Too little detergent is being used or is unsuitable. Troubleshooting ▶ Increase the amount of detergent used or change "Detergent " → Page 27. ▶ Select a more intensive washing programme.
Troubleshooting Fault Coloured deposits (yellow, orange, brown) that are easy to remove are present inside the appliance (mainly at the bottom). en Cause Troubleshooting The formation of films is due 1. Check the setting of the water to ingredients of food remsoftening system. nants and tap water (limes- 2. Add special salt. cale) "soaplike". → "Adding special salt", Page 24 3. If you are using combined detergents (tabs), activate the water softening system. Follow the information about detergents.
en Troubleshooting Fault Irreversible clouding of glassware. Cause Troubleshooting Glasses are not dishwasher- ▶ Use dishwasher-proof glasses. proof, only suitable for dishGlasses are usually only suitable for washers. use in a dishwasher, i.e. long-term wear or long-term changes must be expected. ▶ Avoid a lengthy steam phase (standing time after wash cycle ends). ▶ Use a programme with a lower tem- perature. → "Programmes", Page 17 ▶ Set the softening system to the wa- ter hardness.
Troubleshooting en Home Connect problem Fault Connection to home network is not established. Cause WLAN on router is not active. Troubleshooting ▶ Check the wireless network connection of your router. WLAN display is flashing. Connection to home network is not available. ▶ Activate the wireless network con- Home Connect set incorrectly. ▶ Please consult the documents sup- Technical fault is present. ▶ Please consult the information Home Connect cannot be implemented correctly.
en Troubleshooting Fault Cause Water is left in the appliance Programme has not yet at the end of the proended. gramme. Troubleshooting ▶ Wait until the programme ends or cancel the programme with Reset. Appliance cannot be switched on or operated. Software update is taking place. ▶ Wait until the software update has Appliance functions have failed. 1. Pull out the mains plug or switch off ▶ → "Terminate programme", Page 32 finished. the fuse. 2. Wait at least 2 minutes. 3.
Troubleshooting Fault Appliance door cannot be closed. Cause Door cannot be closed due to installation method. Troubleshooting ▶ Check whether the appliance has been installed properly. When closed, the appliance door, its decor or attached parts should not knock against adjacent cabinets or the worktop. Lid on the detergent dispenser cannot be closed. Detergent dispenser or lid are blocked by sticky detergent residue. ▶ Remove detergent residue.
en Transportation, storage and disposal Clean wastewater pump 8. Insert the pump cover down Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned. WARNING Risk of injury! Sharp and pointed objects or fragments of glass may block the waste water pump and cause injury. ▶ Remove any foreign bodies carefully. 1. Disconnect the appliance from the power supply. 2.
Customer Service Protect appliance from frost Disposing of old appliance If there is a risk of frost where the appliance will be standing, e.g. in a holiday home, empty the appliance completely. ▶ "Empty the appliance." → Page 55 Valuable raw materials can be reused by recycling. Transporting the appliance To avoid damage to the appliance, empty it before transporting. Note: Always transport the dishwasher upright to prevent residual water getting into the machine's controls and damaging the appliance.
en Technical specifications which your appliance was placed on the market within the European Economic Area. Note: Under the terms of the manufacturer's warranty the use of Customer Service is free of charge. Detailed information on the warranty period and terms of warranty in your country is available from our aftersales service, your retailer or on our website. If you contact Customer Service, you will require the product number (ENr.), the production number (FD) and the consecutive numbering (Z-Nr.
Technical specifications en Power consumption Water pressure Inlet rate Water temperature Capacity Off mode/standby mode: 0.50 W Left-on mode: 0.50 W Networked standby: 2.00 W Time in left-on mode: 0 min Time after which appliance is switched to networked standby mode: 10 min Complies with the latest regulations (EU) for energy labels and ecodesign at the time of placing on the market. Additional functions and settings may increase power consumption and times. ¡ Min. 0.05 MPa (0.5 bar) ¡ Max.
en Technical specifications meets the essential requirements and other relevant provisions of the Directive 2014/53/EU. A detailed RED Declaration of Conformity can be found online at www.neff-international.com among the additional documents on the product page for your appliance. BE BG CZ ES FR HR HU MT NL SK FI SE 5 GHz WLAN (Wi-Fi): For indoor use only. 58 DK IT AT UK 2.4 GHz band: 100 mW max. 5 GHz band: 100 mW max.
*9001581358* Constructa-Neff Vertriebs-GmbH Carl-Wery-Straße 34 81739 München GERMANY 9001581358 en 010107 642 V5
