Installation Instruction
Table Of Contents
- Ceiling-mounted ventilation system
- en
- Table of contents
- 1 Safety
- 2 Preventing material damage
- 3 Environmental protection and saving energy
- 4 Operating modes
- 5 Familiarising yourself with your appliance
- 6 Before using for the first time
- 7 Basic operation
- 7.1 Switching on the appliance
- 7.2 Switching off the appliance
- 7.3 Selecting a fan setting
- 7.4 Switching on intensive mode
- 7.5 Switching off intensive mode
- 7.6 Switching on the fan run-on
- 7.7 Switching off the fan run-on
- 7.8 Switch on automatic mode
- 7.9 Switch off automatic mode
- 7.10 Intermittent ventilation
- 7.11 Sensor control
- 7.12 Setting the sensor control
- 7.13 Setting the saturation indicator
- 7.14 Resetting the saturation indicator
- 7.15 Switching on the lighting
- 7.16 Setting the brightness
- 7.17 Switching on the button tone
- 7.18 Switching the button tone off
- 8 Home Connect
- 9 Hob-based hood control
- 10 Cleaning and servicing
- 10.1 Cleaning products
- 10.2 Cleaning the appliance
- 10.3 Cleaning the stainless steel surfaces
- 10.4 Cleaning controls
- 10.5 Removing the grease filter
- 10.6 Cleaning grease filters in the dishwasher
- 10.7 Cleaning grease filters manually
- 10.8 Fitting grease filters
- 10.9 Replacing the batteries in the remote control
- 11 Troubleshooting
- 12 Customer Service
- 13 Accessories
- 14 Disposal
- 15 Declaration of Conformity
- 16 Installation instructions
- 16.1 Included with the appliance
- 16.2 Safety clearances
- 16.3 Dimensions
- 16.4 Secure installation
- 16.5 Information on the installation situation
- 16.6 Instructions for the exhaust air pipe
- 16.7 General information
- 16.8 Instructions for the electrical connection
- 16.9 Installation
Familiarising yourself with your appliance en
7
5 Familiarising yourself with your appliance
5.1 Controls
You can use the control panel to configure all functions
of your appliance and to obtain information about the
operating status.
Tip:Align the remote control as precisely as possible
to the infrared receiver for the LED display.
Switch the appliance on or off
Switching automatic mode
1
on or off
Increase the fan setting
Decrease the fan setting
Switch the lighting on or off
Reduce the brightness
Increase the brightness
1
Depending on the appliance specifications
Switch the fan run-on on or off
HomeConnect
Reset the filter saturation indicator
1
Depending on the appliance specifications
5.2 LED display
Die LED-Anzeige zeigt eingestellte Werte und Funk-
tionen.
81 2 3 4 5 6 7
1
Fan setting 1/grease filter saturation display
2
Fan setting 2/odour filter saturation indicator
3
Fan setting 3
4
Intensive mode 1
5
Intensive mode 2
6
Automatic mode
1
/fan run-on time/interval vent-
ilation
7
HomeConnect
8
Infrared receiver
1
Depending on the appliance specifications
6 Before using for the first time
Configure the settings for initial start-up. Clean the ap-
pliance and accessories.
6.1 Setting an operating mode
Your appliance is set to air extraction mode by default.
To use it in circulating-air mode, you must set the oper-
ating mode.
Note:For use in circulating-air mode, you require addi-
tional Accessories.
Requirement:The appliance is switched off.
1.
Press and hold and for approx.three seconds.
‒ To set circulating-air mode (non-regenerable fil-
ter), press / until LED2 lights up in the LED
display.
‒ To set circulating-air mode (non-regenerable fil-
ter), press / until LED3 lights up in the LED
display.
‒ To convert the electronic control back to opera-
tion without the air recirculation filter, press /
until LED1 lights up on the LED display.
2.
To save the setting, press and hold and for ap-
prox. three seconds.
Or wait approx. 10seconds until the setting is
saved automatically.
To cancel the setting, press .
a A signal tone sounds as soon as the selected set-
ting is saved.
7 Basic operation
7.1 Switching on the appliance
Requirement:Align the remote control as precisely as
possible to the infrared receiver for the LED display.
▶
Press to switch on the appliance.
a The appliance starts at fan setting2.
a The LED for the set fan setting lights up in the LED
display.