Installation Instruction
Table Of Contents
- Ceiling-mounted ventilation system
- en
- Table of contents
- 1 Safety
- 2 Preventing material damage
- 3 Environmental protection and saving energy
- 4 Operating modes
- 5 Familiarising yourself with your appliance
- 6 Before using for the first time
- 7 Basic operation
- 7.1 Switching on the appliance
- 7.2 Switching off the appliance
- 7.3 Selecting a fan setting
- 7.4 Switching on intensive mode
- 7.5 Switching off intensive mode
- 7.6 Switching on the fan run-on
- 7.7 Switching off the fan run-on
- 7.8 Switch on automatic mode
- 7.9 Switch off automatic mode
- 7.10 Intermittent ventilation
- 7.11 Sensor control
- 7.12 Setting the sensor control
- 7.13 Setting the saturation indicator
- 7.14 Resetting the saturation indicator
- 7.15 Switching on the lighting
- 7.16 Setting the brightness
- 7.17 Switching on the button tone
- 7.18 Switching the button tone off
- 8 Home Connect
- 9 Hob-based hood control
- 10 Cleaning and servicing
- 10.1 Cleaning products
- 10.2 Cleaning the appliance
- 10.3 Cleaning the stainless steel surfaces
- 10.4 Cleaning controls
- 10.5 Removing the grease filter
- 10.6 Cleaning grease filters in the dishwasher
- 10.7 Cleaning grease filters manually
- 10.8 Fitting grease filters
- 10.9 Replacing the batteries in the remote control
- 11 Troubleshooting
- 12 Customer Service
- 13 Accessories
- 14 Disposal
- 15 Declaration of Conformity
- 16 Installation instructions
- 16.1 Included with the appliance
- 16.2 Safety clearances
- 16.3 Dimensions
- 16.4 Secure installation
- 16.5 Information on the installation situation
- 16.6 Instructions for the exhaust air pipe
- 16.7 General information
- 16.8 Instructions for the electrical connection
- 16.9 Installation
Preventing material damage en
5
2 Preventing material damage
2.1 Avoiding material damage
ATTENTION!
Condensate may cause corrosion damage.
▶ To prevent condensation from building up, switch on
the appliance during cooking.
If moisture gets into the controls, this may result in
damage.
▶ Never clean controls with a wet cloth.
Incorrect cleaning damages the surfaces.
▶ Follow the cleaning instructions.
▶ Do not use harsh or abrasive detergents.
▶ Clean stainless steel surfaces in the direction of the
finish only.
▶ Never clean controls with stainless steel cleaners.
Condensation that flows back in may damage the ap-
pliance.
▶ The air extraction duct must be installed with a
gradient of at least 1° from the appliance.
If you put incorrect stress on the design elements, they
may break off.
▶ Do not pull design elements.
▶ Do not place objects on the design elements or
hang objects from them.
Leaking batteries may damage the remote control.
▶ Remove the batteries if you are not using the re-
mote control.
▶ Safely dispose of empty or defective batteries in an
environmentally friendly manner.
There is a risk of surface damage if you do not peel off
the protective film.
▶ Remove the protective film from all parts of the ap-
pliance before using for the first time.
3 Environmental protection and saving energy
3.1 Disposing of packaging
The packaging materials are environmentally compat-
ible and can be recycled.
▶
Sort the individual components by type and dispose
of them separately.
Information about current disposal methods are
available from your specialist dealer or local author-
ity.
3.2 Saving energy
If you follow these instructions, your appliance will use
less power.
Adjust the fan speed to the amount of steam pro-
duced during cooking.
¡
The lower the fan speed, the less energy is con-
sumed.
Only use the intensive mode as required.
If cooking produces large amounts of steam, select a
higher fan speed in good time.
¡
The odours are distributed around the room less.
Switch off the lighting if it is no longer required.
¡
When the lighting is switched off, it does not con-
sume any energy.
Clean or replace the filters at regular intervals.
¡
The effectiveness of the filter is retained.
Put the cooking lid on.
¡
The cooking vapours and condensation are re-
duced.
Only use the additional functions if required.
¡
Switching off additional functions reduces power
consumption.