Installation Instruction
Table Of Contents
- Ceiling-mounted ventilation system
- en
- Table of contents
- 1 Safety
- 2 Preventing material damage
- 3 Environmental protection and saving energy
- 4 Operating modes
- 5 Familiarising yourself with your appliance
- 6 Before using for the first time
- 7 Basic operation
- 7.1 Switching on the appliance
- 7.2 Switching off the appliance
- 7.3 Selecting a fan setting
- 7.4 Switching on intensive mode
- 7.5 Switching off intensive mode
- 7.6 Switching on the fan run-on
- 7.7 Switching off the fan run-on
- 7.8 Switch on automatic mode
- 7.9 Switch off automatic mode
- 7.10 Intermittent ventilation
- 7.11 Sensor control
- 7.12 Setting the sensor control
- 7.13 Resetting the saturation indicator
- 7.14 Setting the saturation indicator
- 7.15 Switching on the lighting
- 7.16 Switching off the lighting
- 7.17 Setting the brightness
- 7.18 Switching on the button tone
- 7.19 Switching the button tone off
- 8 Home Connect
- 8.1 Automatically connecting the appliance to the WLAN home network (Wi-Fi)
- 8.2 Manually connecting the appliance to the WLAN home network (Wi-Fi)
- 8.3 Connecting the appliance to the Home Connect app
- 8.4 Home Connect settings
- 8.5 Software update
- 8.6 Resetting the connection
- 8.7 Remote diagnostics
- 8.8 Data protection
- 9 Hob-based hood control
- 10 Cleaning and servicing
- 10.1 Cleaning products
- 10.2 Cleaning the stainless steel surfaces
- 10.3 Cleaning painted surfaces
- 10.4 Cleaning aluminium
- 10.5 Cleaning plastic
- 10.6 Cleaning glass
- 10.7 Cleaning controls
- 10.8 Removing the grease filter
- 10.9 Cleaning grease filters in the dishwasher
- 10.10 Cleaning grease filters manually
- 10.11 Fitting grease filters
- 10.12 Odour filter for recirculating air mode
- 10.13 Replacing the batteries in the remote control
- 11 Troubleshooting
- 12 Customer Service
- 13 Accessories
- 14 Disposal
- 15 Declaration of Conformity
- 16 Installation instructions
Installation instructions en
19
2.
Loosen the screws on the side covers.
20
3.
Open the odour filter cartridge.
4.
Push the side covers inwards and remove them.
5.
Close the odour filter cartridge.
Hanging the appliance
1.
Lift the appliance by the corners and turn it over.
2.
Position the cable that is provided on-site in the
marked area on the appliance.
3.
Guide the cable that is provided on-site through the
opening and hook the appliance into the fastening
screws on the ceiling.
4.
Push the appliance as far as it will go into the four
key hole openings using the guide sleeves.
5.
Move the appliance and lower it further so that the
collar nuts are positioned on the edge of the guide
sleeves.
6.
Carefully tighten the diagonally opposite collar nuts
until the appliance is flush-mounted on the ceiling.
13
Tighten the collar nuts one at a time so that the ap-
pliance does not tilt when doing so.
Connecting the appliance
Requirement:Ensure that the protection against con-
tact is guaranteed during installation.
1.
Guide the cable that is provided on-site through the
opening in the appliance.
Maintain the bending radius of the cable that is
provided on-site for connecting the appliance.
The cable must remain doubly insulated. You should
therefore strip the cable as little as possible up-
stream of the connecting terminal.