Installation Instruction
Table Of Contents
- Ceiling-mounted ventilation system
- en
- Table of contents
- 1 Safety
- 2 Preventing material damage
- 3 Environmental protection and saving energy
- 4 Operating modes
- 5 Familiarising yourself with your appliance
- 6 Before using for the first time
- 7 Basic operation
- 7.1 Switching on the appliance
- 7.2 Switching off the appliance
- 7.3 Selecting a fan setting
- 7.4 Switching on intensive mode
- 7.5 Switching off intensive mode
- 7.6 Switching on the fan run-on
- 7.7 Switching off the fan run-on
- 7.8 Switch on automatic mode
- 7.9 Switch off automatic mode
- 7.10 Intermittent ventilation
- 7.11 Sensor control
- 7.12 Setting the sensor control
- 7.13 Resetting the saturation indicator
- 7.14 Setting the saturation indicator
- 7.15 Switching on the lighting
- 7.16 Switching off the lighting
- 7.17 Setting the brightness
- 7.18 Switching on the button tone
- 7.19 Switching the button tone off
- 8 Home Connect
- 8.1 Automatically connecting the appliance to the WLAN home network (Wi-Fi)
- 8.2 Manually connecting the appliance to the WLAN home network (Wi-Fi)
- 8.3 Connecting the appliance to the Home Connect app
- 8.4 Home Connect settings
- 8.5 Software update
- 8.6 Resetting the connection
- 8.7 Remote diagnostics
- 8.8 Data protection
- 9 Hob-based hood control
- 10 Cleaning and servicing
- 10.1 Cleaning products
- 10.2 Cleaning the stainless steel surfaces
- 10.3 Cleaning painted surfaces
- 10.4 Cleaning aluminium
- 10.5 Cleaning plastic
- 10.6 Cleaning glass
- 10.7 Cleaning controls
- 10.8 Removing the grease filter
- 10.9 Cleaning grease filters in the dishwasher
- 10.10 Cleaning grease filters manually
- 10.11 Fitting grease filters
- 10.12 Odour filter for recirculating air mode
- 10.13 Replacing the batteries in the remote control
- 11 Troubleshooting
- 12 Customer Service
- 13 Accessories
- 14 Disposal
- 15 Declaration of Conformity
- 16 Installation instructions
en Cleaning and servicing
12
Requirement:The grease filters have been removed.
→"Removing the grease filter", Page11
1.
Observe the information regarding the cleaning
agents.
→"Cleaning products", Page10
2.
Soak the grease filter in hot soapy water.
Use special grease solvent for stubborn dirt. You
can obtain grease solvents from after-sales service
or the online shop.
3.
Use a brush to clean the grease filters.
4.
Rinse the grease filters thoroughly.
5.
Allow the grease filters to drain.
10.11 Fitting grease filters
ATTENTION!
Falling grease filters may damage the hob below.
▶ Grip below the grease filter with one hand.
1.
Fit the grease filters.
2.
Fold the grease filters upwards and engage the
locks.
3.
Make sure that the locks engage.
4.
Close the filter cover.
5.
Make sure that the filter cover locks engage cor-
rectly.
10.12 Odour filter for recirculating air mode
You can obtain odour filters from the after-sales service
or the online shop. Only use original odour filters.
→"Accessories", Page14
Replacing the odour filter
Requirement:The grease filters have been removed.
1.
Open the odour filter cartridge.
2.
Remove the odour filter.
3.
Remove the new odour filter from the packaging.
4.
Insert the odour filter.
Insert the odour filter in the correct direction.
5.
Close the odour filter cartridge.
6.
→"Fitting grease filters", Page12.
10.13 Replacing the batteries in the remote
control
WARNING‒Risk of injury!
Children may swallow batteries.
▶ Keep batteries out of the reach of children.
▶ Keep an eye on any children when you are repla-
cing batteries.
Batteries may explode.
▶ Do not charge the batteries.
▶ Do not short-circuit the batteries.
▶ Do not throw batteries into a fire.
ATTENTION!
Improper handling of batteries.
▶ Do not short-circuit the terminals.
▶ Use the specified type of batteries only.
▶ Do not use different battery types together.
▶ Do not use new and used batteries together.
▶ Do not use rechargeable batteries.
Leaking batteries may damage the remote control.
▶ Remove the batteries if you are not using the re-
mote control.
▶ Safely dispose of the empty or defective batteries in
an environmentally friendly manner.
1.
Remove the cover.
2.
Remove the empty batteries.
3.
Insert the new batteries (3VCR2032).
4.
Close the cover.
5.
Dispose of the empty batteries in an environmentally
friendly manner.