Installation Instruction
Table Of Contents
- Extractor hood
- en
- Table of contents
- 1 Safety
- 2 Avoiding material damage
- 3 Environmental protection and saving energy
- 4 Operating modes
- 5 Familiarising yourself with your appliance
- 6 Basic operation
- 6.1 Switching on the appliance
- 6.2 Switching off the appliance
- 6.3 Setting a fan setting
- 6.4 Switching on intensive mode
- 6.5 Switching off intensive mode
- 6.6 Switching on the fan run-on
- 6.7 Switching off the fan run-on
- 6.8 Switching on the AirFresh function
- 6.9 Switching on the NoiseReduction function
- 6.10 Sensor control
- 6.11 Setting the sensor control
- 6.12 Switching on the lighting
- 6.13 Setting the brightness
- 6.14 Switching on Ambient Light
- 6.15 Ambient Light - Setting the brightness
- 6.16 Ambient Light - adjusting the colour
- 6.17 Setting the intermediate position for the filter cover
- 6.18 Switching on the audible signal
- 7 Home Connect
- 8 Hob-based hood control
- 9 Cleaning and servicing
- 10 Troubleshooting
- 11 Disposal
- 12 Customer Service
- 13 Accessories
- 14 Declaration of Conformity
- 15 Installation instructions
en Cleaning and servicing
10
1.
Observe the information regarding the cleaning
agents.
→"Cleaning products", Page9
2.
Clean as follows, depending on the surface:
‒ Clean stainless steel surfaces in the direction of
the finish using a sponge cloth and hot soapy
water.
‒ Clean painted surfaces using a damp sponge
cloth and hot soapy water.
‒ Clean aluminium using a soft cloth and glass
cleaner.
‒ Clean plastic using a soft cloth and glass
cleaner.
‒ Clean glass using a soft cloth and glass cleaner.
3.
Dry with a soft cloth.
4.
Apply a thin layer of the stainless steel cleaning
product to stainless steel surfaces using a soft
cloth.
You can obtain stainless steel cleaning products
from the after-sales service or the online shop.
9.3 Cleaning controls
WARNING‒Risk of electric shock!
Penetrating moisture may cause an electric shock.
▶ Do not use wet sponge cloths.
1.
Observe the information regarding the cleaning
agents.
→"Cleaning products", Page9
2.
Clean using a damp sponge cloth and hot soapy
water.
3.
Dry with a soft cloth.
9.4 Removing the grease filter
WARNING‒Risk of injury!
Risk of injury when opening and closing the hinges.
▶ Keep your hands away from the hinges.
The filter cover may swing out.
▶ Open the filter cover slowly.
▶ Take hold of the filter cover after opening until it no
longer swings out.
▶ Close the filter cover slowly.
Items placed on the appliance may fall off.
▶ Before opening the appliance, remove any objects
from the shelf.
1.
Take hold of the filter cover in the centre and open it
fully.
2.
ATTENTION!
Falling grease filters may damage the hob below.
▶ Grip below the grease filter with one hand.
Open the lock on the grease filter and fold down the
grease filter.
3.
Remove the grease filters from the holders.
To prevent grease from dripping, hold the grease fil-
ter horizontally.
9.5 Fitting the grease filters
1.
ATTENTION!
Falling grease filters may damage the hob below.
▶ Grip below the grease filter with one hand.
Note:Note the correct position of the grease filter.
Insert the grease filter.
2.
The lock on the grease filter clicks into place.
3.
If the grease filter has been inserted incorrectly,
carefully push the lock forwards, remove the grease
filter and insert it correctly.