Installation Instruction

Basic operation en
7
6.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
1.
To switch on intensive mode 2, press ⁠.
a ⁠ ⁠ appears on the display.
2.
To switch on intensive mode 1, press ⁠ again.
a ⁠ ⁠ appears on the display.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
6.5 Switching off intensive mode
▶
Press ⁠.
6.6 Switching on the fan run-on, variant1
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
▶
Press ⁠.
a The fan run-on starts at fan setting1.
a The appliance switches off automatically after ap-
prox. 10 minutes.
6.7 Switching on the fan run-on, variant2
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
▶
Press ⁠ until ⁠ appears on the display.
a The fan run-on starts at fan setting1.
a The appliance switches off automatically after ap-
prox. 10 minutes.
6.8 Switching off the fan run-on, variant 1
▶
Press ⁠.
6.9 Switching off the fan run-on, variant 2
▶
Press ⁠.
6.10 Switching on the AirFresh function
The AirFresh function switches on the ventilation sys-
tem for approx.five minutes per hour at fan setting1.
▶
Press ⁠.
a ⁠ appears on the display.
6.11 Switching on the NoiseReduction
function
The noise reduction function reduces the fan noise.
The function is possible in all fan settings, except in fan
setting ⁠.
▶
Press ⁠.
a The NoiseReduction function remains active even
after the appliance is switched off.
6.12 Switching on automatic mode
The optimum fan setting is set automatically using a
sensor.
▶
Press ⁠.
6.13 Switching off automatic mode
1
▶
Press ⁠.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
6.14 Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on. If the
sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Factory setting:5
¡ Lowest setting:0
¡ Highest setting:9
6.15 Setting the sensor control
1
Requirement:The appliance is switched on.
1.
Press and hold ⁠.
a The setting is displayed after approx. onesecond.
2.
Press ⁠or ⁠ to change the setting.
3.
Release ⁠ to save the setting.
6.16 Switching on the lighting
The lighting can be switched on and off independently
of the ventilation system.
▶
Press ⁠.
6.17 Setting the brightness
▶
Press and hold ⁠ until the required brightness is
reached.
6.18 Switching on Ambient Light
1
You can switch on the Ambient Light independently of
the ventilation system.
▶
Press ⁠.
6.19 Ambient Light
1
- Setting the brightness
▶
Press and hold ⁠ until the required brightness is
reached.
6.20 Ambient Light
1
- adjusting the colour
Requirement:The appliance is switched off.
1.
Press ⁠.
2.
Press ⁠or ⁠ repeatedly until the required colour is
set.
1
Depending on the appliance specifications