EXTRACTOR HOOD [en] Instructions for installation and use
en Ú Table of contents [ e n ] I n s t r u c t i o n s f o r i ns t a l a t i o n a n d u s e INSTRUCTION MANUAL ..........................................................3 8 Intended use ......................................................... 3 ( Important safety information .............................. 4 7 Environmental protection.................................... 6 Ç Operating modes.................................................. 6 1 Operating the appliance ....................................
en Important safety information (Important safety information :Warning – Danger of suffocation! Packaging material is dangerous to children. Never allow children to play with packaging material. I mpor t ant saf et y i nf or mat i on : Warning – Danger of death! Risk of poisoning from flue gases that are drawn back in. Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room airdependent heat-producing appliance is being operated.
Important safety information en : Warning – Risk of burns! Causes of damage ■ Caution! Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage. The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance. Risk of burns! ■ The appliance becomes hot during operation. Allow the appliance to cool down before cleaning.
en Environmental protection 7Environmental protection Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly. Envi r onment al pr ot ect i on ÇOperating modes Oper at i ng modes Exhaust air mode The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.
Operating the appliance 1Operating the appliance These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. Oper at i ng t he ap l i ance en Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. This is the most effective way of removing the kitchen fumes.
en Operating the appliance Lighting Audible signal The lighting can be switched on and off independently of the fan. Switching on Touch the 6 symbol. Setting the brightness Press and hold the 6 symbol until the required brightness is reached.
Operating the appliance en Control panel model 2 Symbol # Q 3 A @ ˜ ‘ 6 Explanation Fan on/off Noise reduction function AirFresh function Reduce fan setting/fan run-on Increase fan settings/intensive mode 1, 2 Intensive mode 2 shortcut Automatic air sensor Light on/off/dimming Automatic mode Switching on 1. Touch the # symbol. The fan will start at setting ƒ. 2. Touch the ‘ symbol. The optimum fan setting is set using an automatic air sensor.
en Operating the appliance Noise reduction function The noise reduction function reduces the fan noise. Switching on Note: This function can be used at any fan setting except fan setting ‚. The function will remain active even after the fan is switched off. Switching over the display for air recirculation mode For air recirculation mode, the electronic controller must be switched over accordingly: ■ ■ Touch the Q symbol. Switching off Touch the Q symbol.
Cleaning and maintenance 2Cleaning and maintenance Glass :Warning – Risk of burns! The appliance becomes hot during operation. Allow the appliance to cool down before cleaning. Controls Cl eani ng and mai nt enance : Warning Risk of electric shock! Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.
en Trouble shooting By hand: Note: You can use a special degreaser to remove stubborn dirt. This can be ordered from the online shop. 3Trouble shooting Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service. Tr oubl e sho t i ng ■ ■ ■ Soak the metal grease filters in hot soapy water. Clean the filters with a brush and then rinse them thoroughly. Leave the metal grease filters to drain on an absorbent material.
Customer service en 4Customer service Accessories When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access). You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required.
Installation instructions en INSTALLATION INSTRUCTIONS I ns t al at i on i ns t r uc t i ons PLQ PP PD[ PP PLQ PP PP (Important safety information Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.
Important safety information : Warning – Risk of death! Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible.
en Important safety information : Warning – Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation. Risk of electric shock! ■ It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed.
General information KGeneral information Checking the wall ■ Gener al i nf or mat i on Exhaust air mode : Warning – Risk of death! Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances.
en Installation 5Installation I ns t al at i on Preparing the installation Installation 1. Screw on the fixing bracket for the flue duct. ¨ $ Caution! Ensure that there are no electrical wires, gas pipes or water pipes in the area where holes are to be drilled. 1. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood. 2. Use the enclosed template to mark the positions for the screws and the outline of the attachment area. 3.
Installation Attaching and aligning the appliance Connecting the pipes 1. First, remove the protective foil from the back of the Note: If using an aluminium pipe, smooth the connection area beforehand. appliance and, following installation, remove the foil completely. 2. When attaching the appliance, ensure that it engages firmly with the brackets. « 3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left.
Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd.
