[en] Instructions for installation and use Extractor hood
Ú Table of contents alondustifr[e]Ice INSTRUCTION MANUAL............................................................ 2 Important safety information................................................ 2 Environmental protection ..................................................... 4 Environmental protection..............................................................4 Operating modes................................................................... 4 Exhaust air mode .........................................
Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied.
Risk of electric shock! ■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service. ■ Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.
Operating the appliance These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. Explanation A Light On/Off Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. This is the most effective way of removing the kitchen fumes. 0.
Cleaning the metal mesh grease filters ■ Clean the filters with a brush and then rinse them thoroughly. : Risk of fire! ■ Leave the metal mesh grease filters to drain. Grease deposits in the grease filter may catch fire. Clean the grease filter at least every 2 months. Never operate the appliance without the grease filter. Removing metal mesh grease filter Notes ■ Do not use any aggressive, acidic or alkaline cleaning agents.
After-sales service Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician. Accessories for circulating-air mode When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access).
INSTALLATION INSTRUCTIONS Ins tallation in structio ns PLQ PLQ PLQ PLQ ! [ [ [ [ [ ! ■ ■ ■ This appliance is installed on the wall. Follow the enclosed installation instructions for additional special accessories (e.g. for circulating-air mode). The surfaces of the appliance are sensitive. Avoid damaging them during installation. : Important safety information Read these instructions carefully.
Adequate incoming air must therefore always be ensured. ■ An incoming/exhaust air wall box alone will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heatproducing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes or by other technical means.
Checking the wall ■ ■ ■ ■ The wall must be level, vertical and adequately load-bearing. The depth of the bore holes must be the same length as the screws. The wall plugs must have a secure grip. The enclosed screws and wall plugs are suitable for solid brickwork. Suitable fasteners must be used for other structures (e.g. plasterboard, porous concrete, poroton bricks). This appliance may be connected to a correctly installed earthed socket only. Attach the earthed socket preferably inside the flue duct.
Finishing installation of the appliance Attaching the flue duct 1. Drill an 8 mm Ø hole to a depth of 80 mm for the safety : Risk of injury! 2. Initially remove the protective foil from the back of the Components inside the appliance may have sharp edges. Wear protective gloves. screw and press the wall plug flush into the wall. ¨ appliance and, following installation, remove the foil completely. 1. Separate the flue ducts. To do this, remove the adhesive tape 3. Attach the appliance. © 4.
Constructa Neff Vertriebs-GmbH Carl-Wery-Straße 34 D-81739 München *9000773717* 9000773717 920712
