User Manual

en Before using for the first time
10
KBefore using for the first
time
Before using for the first time Before you can use your new appliance, you must
make some settings. You must also clean the cooking
compartment and accessories.
Before using for the first time
Before using the appliance for the first time, enquire
about the water hardness of your tap water from your
water supplier.
So that the appliance can reliably remind you to
decalcify it when required, you must correctly set your
water hardness range.
Caution!
The appliance may be damaged if unsuitable liquids are
used.
Do not use distilled water, highly chlorinated tap water
(>40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or
uncarbonated mineral water.
Notes
■ If your water is very hard, we recommend that you
use softened water.
■ If you only use softened water, you can set the water
hardness range to "softened" in this case.
■ If you use mineral water, set the water hardness
range to "4 very hard".
■ If you use mineral water, only use uncarbonated
mineral water.
Initial use
As soon as the appliance is connected to the power
supply, the first setting "Language" appears on the
display.
Setting the language
1. Use the & button to navigate to the bottom line.
2. Use the ( or ) button to select the language.
3. Use the % button to return to "Language".
4. Use the ) button to select the next setting.
Setting the time
1. Use the & button to navigate to the next line.
2. Use the ( or ) button to select the current time.
3. Press the % button.
4. Use the ) button to select the next setting.
Setting the date
1. Use the & button to navigate to the next line.
2. Use the ( or ) button to select the current day.
3. Use the % button to return to "Day".
4. Use the ) button to select the next setting.
5. Use the & button to navigate to the next line.
6. Use the ( or ) button to select the current month.
7. Use the % button to return to "Month".
8. Use the ) button to select the next setting.
9. Use the & button to navigate to the next line.
10. Use the ( or ) button to select the current year.
11. Use the % button to return to "Year".
12. Use the ) button to select the next setting.
Setting the water hardness
1. Use the & button to navigate to the bottom line.
2. Use the ( or ) button to select the water hardness
range.
3. Use the % button to return to "Water hardness".
4. Use the ) button to apply the settings.
The initial use is complete.
Notes
■ You can change these settings at any time in the
basic settings. ~ "Basic settings" on page 18
■ After connecting the appliance to the power or
following a power cut, the settings for initial use are
shown in the display.
Calibrating the appliance and cleaning the
cooking compartment
The boiling point of water depends on the air pressure.
During calibration, the appliance sets itself to the
pressure ratio at the installation location.This occurs
automatically during the first steam operation. This
results in a lot of steam.
Preparing the calibration
1. Remove the accessories from the cooking
compartment.
2. Remove leftover packaging, such as polystyrene
pellets, from the cooking compartment.
3. Before calibrating the appliance, wipe the smooth
surfaces in the cooking compartment with a soft, wet
cloth.
Calibrating the appliance and cleaning the cooking
compartment
Notes
■ The calibration can only be started once the cooking
compartment is cold (room temperature).
■ Do not open the appliance door during calibration.
Calibration will otherwise be interrupted.
1. Use the # touch button to switch on the appliance.
2. Fill the water tank. ~ "Filling the water tank"
on page 11
Water hardness range Setting
0 0 softened
1 (up to 1.3 mmol/l) 1 soft
2 (1.3 - 2.5 mmol/l) 2 medium
3 (2.5 - 3.8 mmol/l) 3 hard
4 (above 3.8 mmol/l) 4 very hard