Instructions for Use

en Cleaning function
24
■ Do not open the appliance door while it is running.
Doing this will interrupt the EasyClean š cleaning
aid.
1. Remove any accessories from the cooking
compartment.
2. Mix 0.4 litres water (not distilled water) with a drop of
washing-up liquid and pour into the middle of the
cooking compartment floor.
3. Use the function selector to set the cleaning
functions 2.
The 2 symbol and the cleaning functions will
appear on the display.The first cleaning function is
highlighted.
4. Press the ) or ( button repeatedly until the š symbol
is highlighted.
"EASY" will appear on the display.
5. Turn the temperature selector.
"On" will appear on the display.
The cleaning aid will start after a few seconds.The
duration will count down on the display.
Note: The interior lighting remains off while the cleaning
aid is running.
If œ flashes on the display when the function is switched
on, this indicates that the cooking compartment has not
completely cooled down. Switch off the appliance. Wait
until the cooking compartment has cooled down and
switch the cleaning aid back on.
Once the cleaning aid has run through to the end, an
audible signal will sound.
Subsequent cleaning
The remaining water in the cooking compartment must
be removed promptly. Do not leave the remaining water
in the cooking compartment for a long time (e.g.
overnight). The appliance must not be operated when
the cooking compartment is still wet or damp.
1. Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2. Clean the smooth surfaces in the cooking
compartment with a dish cloth or a soft brush.
Stubborn residues can be removed using a stainless
steel scouring pad.
3. Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4. To switch off, turn the function selector to the zero
setting.
5. Depending on the appliance type, open or lower the
appliance door to the stop position (approx. 30°)
and leave it open for approx. one hour to allow the
enamel surfaces in the cooking compartment to dry
thoroughly. Alternatively, you can also run the rapid
drying function for the cooking compartment.
Running the rapid drying function for the cooking
compartment
1. Once the cleaning aid has been run through,
depending on the appliance type, open or lower the
appliance door to the stop position (approx. 30°).
2. Start CircoTherm hot air at 50 °C.
3. After five minutes, switch off the appliance and close
the appliance door.
Removing heavy deposits of dirt
You have several options for removing particularly
stubborn deposits of dirt.
■ Leave the soapy water to work for some time before
starting the cleaning aid.
■ Rub soapy water onto the dirt on the smooth
surfaces before starting the cleaning aid.
■ Repeat the cleaning aid after the cooking
compartment has cooled down.
Descaling
To ensure that your appliance continues to operate
correctly, it must be descaled regularly.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
The , symbol appears on the display if the appliance
needs to be descaled.
There are four steps in the descaling programme. For
hygiene reasons, the descaling programme must be
run through completely before the appliance is ready
for operation again. Descaling takes around 90–
110 minutes in total:
■ First step (1_4): Descale (approx. 65 minutes), then
empty and refill the water tank
■ Second step (2/4): Rinse (approx. 9 minutes), then
empty and refill the water tank
■ Third step (3_4): Rinse (approx. 9 minutes), then
empty and refill the water tank
■ Fourth step (4_4): Rinse (approx. 9 minutes), then
empty and dry the water tank
Start descaling
Caution!
■ Risk of damage to the appliance: Only use the liquid
descaler recommended by us for the descaling
programme. The length of time for which the
descaler is left to work is based on this product.
Using other descalers may damage the appliance.
Descaler order no. 311 680
■ Descaling solution: Do not allow any descaling
solution or descaler to come into contact with the
control panel or other surfaces on the appliance.
This may damage the surfaces. If this does happen,
remove the descaling solution immediately with
water.
Note: Do not pour more than 150 ml of liquid into the
water tank throughout the descaling process.
First step (1_4)
1. Mix 100 ml water with 50 ml liquid descaler to make
a descaling solution.
2. Pour the descaling solution into the water tank and
insert the water tank.
3. Use the function selector to set the cleaning
functions 2.
The 2 symbol and the cleaning functions appear
on the display. The first cleaning function is
highlighted.
4. Press the ) or ( button repeatedly until the , symbol
is highlighted.
"’‘–’" appears on the display.