Installation Instruction

Basic settings en
19
Display Basic setting Selection
Cooling fan run-on time = short
= medium
1
= long
= extra long
Telescopic shelves retrofitted
2
= no
1
(for rails and 1-level pull-out)
= yes (for 2- and 3-level pull-out)
Sabbath mode available = no
1
= yes
Water hardness
→"Setting the water hardness", Page19
= softened
= soft (up to 1.5mmol/l)
= medium (1.5–2.5mmol/l)
= hard (2.5–3.8mmol/l)
1
= very hard (above 3.8mmol/l)
Reset all values to factory settings = no
1
= yes
1
Factory setting (may vary according to model)
2
Depending on the appliance specifications
14.2 Changing basic settings
Requirement:The appliance is switched off.
1.
Press and hold the button for approximately
fourseconds.
a The first basic setting appears in the display,
e.g. ⁠ ⁠ ⁠ ⁠.
2.
Use the temperature selector to change the setting.
3.
Use the or button to switch to the next basic set-
ting.
4.
To save the changes, press and hold the button
for approx. fourseconds.
Note:Your changes to the basic settings will be re-
tained even after a power failure.
14.3 Discarding changes to the basic
settings
▶
Turn the function selector.
a All changes are discarded and not saved.
14.4 Setting the water hardness
ATTENTION!
If the wrong water hardness has been set, the appli-
ance cannot remind you to descale it at the right time.
▶
Set the water hardness correctly.
Using unsuitable liquids may damage the appliance.
▶
Do not use distilled water, highly chlorinated tap wa-
ter (>40 mg/l) or other liquids.
▶
Only use cold, fresh tap water, softened water or
non-carbonated mineral water.
Requirements
¡ Before you set the water hardness, ask your water
supplier about the hardness of your tap water.
¡ The appliance must be switched off.
1.
Press and hold the button for approximately
fourseconds.
a The first basic setting appears in the display,
e.g. ⁠ ⁠ ⁠ ⁠.
2.
Use the or button to switch to the next basic set-
ting ⁠ ⁠ ⁠.
3.
Use the temperature selector to set the water hard-
ness.
Tip:If your tap water is very hard, we recommend
that you use softened water. If you use only
softened water, you can set your appliance to the
"softened" water hardness range.
Tip:If you use mineral water, set the water hardness
range to "very hard". If you use mineral water, you
must only use non-carbonated mineral water.
Water hardness
basic setting
Water
hardness
in mmol/l
German
hardness
in °dH
French
hardness
°fH
⁠ ⁠ ⁠ =
softened
1
- - -
⁠ ⁠ ⁠ =soft Up to 1.5 Up to 8.4 Up to 15
⁠ ⁠ ⁠ = me-
dium
1.5-2.5 8.4-14 15-25
⁠ ⁠ ⁠ = hard 2.5-3.8 14-21.3 25-38
⁠ ⁠ ⁠ =very
hard
2
Above
3.8
Above
21.3
Above 38
1
Only set this if you will be using solely softened
water.
2
Also set for mineral water. Only use non-carbon-
ated mineral water.
4.
To save the changes, press and hold the button
for approx. fourseconds.