Installation instructions

Cleaning functions en
29
9.
After using the cleaning aid, finish cleaning the
cooking compartment.
→"Wiping down the cooking compartment",
Page29
Wiping down the cooking compartment
ATTENTION!
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶ After using the cleaning aid, wipe the cooking com-
partment clean and allow it to dry fully.
Requirement:The cooking compartment must have
cooled down.
1.
Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2.
Clean the smooth surfaces in the cooking compart-
ment with a dish cloth or a soft brush. Remove stub-
born food remnants using a stainless steel scouring
pad.
3.
Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4.
If there is any stubborn dirt that you are unable to
remove, run the cleaning aid again once the cook-
ing compartment has cooled down.
5.
Leave the cooking compartment to dry with the ap-
pliance door open for approx. 1hour.
19.3 Descaling
To ensure that your appliance continues to operate cor-
rectly, it must be descaled regularly.
How frequently you need to run the descaling pro-
gramme will depend on the water hardness and how
many times you have used the steam function. The ap-
pliance indicates when only another five or fewer
steam-assisted operations are possible. If you do not
carry out the descaling, you can no longer set any op-
eration with steam.
Descaling comprises several steps and takes approx.
70–95minutes:
¡ Descaling (approx. 55–70minutes)
¡ First rinse cycle (approx. 9–12minutes)
¡ Second rinse cycle (approx. 9–12minutes)
For reasons of hygiene, the descaling programme must
be run in full.
If descaling is interrupted, you can no longer set any
operation. To ensure that the appliance is ready for op-
eration again, carry out two rinse cycles.
Preparing descaling
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
▶ Only use the liquid descaler recommended by us
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
▶ Remove descaling solution immediately with water.
1.
Mix the descaling solution:
‒ 200ml liquid descaler
‒ 400ml water
2.
Open the control panel.
3.
Remove the water tank and pour the descaling solu-
tion into it.
4.
Once the descaling solution has been poured into
the water tank, slide the tank back in.
5.
Close the control panel.
Setting the descaling process
ATTENTION!
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
▶ Remove descaling solution immediately with water.
Requirement:The appliance must be prepared for de-
scaling. →Page29
1.
Press ⁠ to switch the appliance on.
2.
Press ⁠.
3.
Swipe left or right to set "Descale" ⁠.
4.
Press the bottom row.
a The duration will appear on the display. You cannot
change the duration of the descaling process.
5.
Press the bottom row.
6.
Press ⁠ to start the descaling process.
a The descaling process will start. The duration will
count down on the display.
a Once the descaling process has run through to the
end, an audible signal will sound.
Running the first rinse cycle
1.
Open the control panel and remove the water tank.
2.
Thoroughly rinse the water tank and fill it with fresh
water.
3.
Slide in the water tank and close the control panel.
4.
Press ⁠ to start the rinse cycle.
a The rinse cycle will start. The duration will count
down on the display.
a Once the rinse cycle has run through to the end, an
audible signal will sound.
Running the second rinse cycle
1.
Open the control panel and remove the water tank.
2.
Thoroughly rinse the water tank and fill it with fresh
water.
3.
Slide in the water tank and close the control panel.
4.
Press ⁠ to start the rinse cycle.
a The rinse cycle will start. The duration will count
down on the display.
a Once the rinse cycle has run through to the end, an
audible signal will sound.
5.
Empty and dry the water tank.
→"Emptying the water tank", Page15