Quick Start Guide
1
8
9
10
A1
A2
A3
A4
-
A
YYYY-MM-DD
Documentation released
-
Ref.Nr.
REV.
DATE
DESCRIPTION
APPROVED
N/A
DIM. IN MM
ROUGHNESS ACC.
ISO 1302 in µM
GENERAL TOLERANCES
SCALE:
FORMAT:
DRAWING:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
A
B
C
D
E
F
6
3
2
1
F
E
D
C
B
A
5
6
7
8
A3
cube
N/A
A.01
ARTICLE NUMBER
REV.
ISO A
GROENLO HOLLAND
SHEET:
4
7
8
5
4
3
2
1
10.01 OF 1
1:1
± 1°
± 0.2
DESCRIPTION
LIN.
ANG.
N/A
??
??
??
DRW:
CHCK:
2009-MM-DD
2009-MM-DD
2009-MM-DD
DSGN:
connect Card reader to the CUBE Core or CUBE Access Plus
05
1
2
3
4
-
A
YYYY-MM-DD
Documentation released
-
Ref.Nr.
REV.
DATE
DESCRIPTION
APPROVED
N/A
DIM. IN MM
ROUGHNESS ACC.
ISO 1302 in µM
GENERAL TOLERANCES
SCALE:
FORMAT:
DRAWING:
Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this
drawing may be reproduced or distributed in any form or by any means, or stored
in a data base or retrieval system without the prior written permission of NEDAP.
A
B
C
D
E
F
6
3
2
1
F
E
D
C
B
A
5
6
7
8
A3
Assem21
N/A
A.01
ARTICLE NUMBER
REV.
ISO A
GROENLO HOLLAND
SHEET:
4
7
8
5
4
3
2
1
10.01 OF 1
1:1
± 1°
± 0.2
DESCRIPTION
LIN.
ANG.
N/A
??
??
??
DRW:
CHCK:
YYYY-MM-DD
YYYY-MM-DD
YYYY-MM-DD
DSGN:
1 2 3 4
MK170W
MK170B
2
!
Blank wire
Reader
Brown
White
Green
Yellow
: +12V
: Ground GND
: RS485 +
: RS485 -
To door locker
To door locker
connectors
Use crimp connectors and isolation
for wire extension
Connect reader(s)
See wiring instructions reader
Cable Signal name Reader cable
White Reader Ground Black
Brown Reader Power +12V Red
Green Reader RS485 + Yellow
Yellow Reader RS485 - Blue
See also pre-installation
1
Cable shield must be connected to Power GND of CUBE
Card-reader (A2) and GND of external device (metal case)
FCC ID: CGDINVEXS170 and IC: 1444A-INVEXS170
Compliance statements (part15.19)
This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Cet appareil se conforme aux normes RSS210 exemptés de license du Industry Canada. L’opération est soumis
aux deux conditions suivantes:
(1) cet appareil ne doit causer aucune interférence, et
(2) cet appareil doit accepter n’importe quelle interférence, y inclus interférence qui peut causer une opération
non pas voulu de cet appareil.
Warning (part15.21)
Changes or modications not expressly approved by party responsible for compliance could void the user’s
authority to operate the equipment.