Smartcard-Booster LEGI C I nstallation Guide 2012-02-21 This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no license under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher.
Smartcard-Booster LEGIC CONTENTS 1 INTRODUCTION .......................................................................................................................................................................................3 2 INSTALLATION .........................................................................................................................................................................................4 3 2.1 DIMENSIONS......................................................
Smartcard-Booster LEGIC 1 INTRODUCTION The Smartcard-Booster LEGIC is an active dual ID tag enabling simultaneous identification of the inserted LEGIC smart card and the embedded vehicle ID resulting in rapid driver and vehicle monitoring. A LEGIC smart card can be placed in the device (representing driver ID). Additionally a separate ID is programmed in the Smartcard-Booster (representing vehicle ID).
Smartcard-Booster LEGIC 2 INSTALLATION 2.1 DIMENSIONS The Smartcard-Booster is easily mounted on the interior of the car’s windshield by means of suction cups. Users should ensure the visual contact between the Booster and any TRANSIT reader is unobstructed with items such as stickers or metalized windshields (see also chapter 2.3 about solar control windshields). Note: The suction cups must be faced toward the reader to achieve maximum reading distance.
Smartcard-Booster LEGIC 2.2 TEMPERATURE CONSIDERATIONS The Smartcard-Booster is designed to operate within the extreme temperature ranges, which often occur behind a vehicle’s windshield during the winter or summer seasons (-20°C to 85°C). However the LEGIC card inserted in the Booster may not be designed to withstand such temperatures and could suffer damage as a result. Nedap advises to remove the LEGIC card when not in use.
Smartcard-Booster LEGIC 3 CONFIGURATION The Smartcard-Booster LEGIC is configured by means of configuration cards. This configuration card is a LEGIC Advant transponder that contains all the information that is required to find the user's segment and read the data. The Smartcard-Booster LEGIC only accepts a configuration card after configuration is enabled with a master token card. A newly purchased booster will accept any master token card.
Smartcard-Booster LEGIC 3.3 CONFIGURATION SOFTWARE NEDAP has developed a software application that allows system integrators to create configuration cards. This software can be downloaded from our website www.nedapavi.com . Note: A LEGIC Advant programmer is required. For example the KABA B-Net 91 07. LEGIC Boost er Config soft w are © Nedap AVI, P.O.
Smartcard-Booster LEGIC 3.3.1 CREATE A CONFIGURATION CARD The configuration card contains the information which user cards are supported and which data on these cards must be read. Follow the procedure below to create a configuration card. 1. Specify the OPTIONS (see chapter 3.3.1.1) 2. Specify the SEARCH DEFINITIONS (see chapter 3.3.1.3) 3. Specify the DATA DEFINITIONS (see chapter 3.3.1.4) 4. Load the Master Token IAM.
Smartcard-Booster LEGIC 3.3.1.2 RFID OPTIONS Enable ISO15693 ■ The ISO15693 protocol is always enabled because it is required to read the configuration cards. Enable ISO14443A ■ Enables reading ISO14443A cards. Enable LEGIC prime ■ Enables reading LEGIC Prime cards. Enable Inside Contactless □ Enables reading Inside Contactless cards (UID only). Enable FeliCa □ Enables reading Sony Felica cards (UID only). Requires Smartcard-Booster LEGIC 2G.
Smartcard-Booster LEGIC 3.3.1.4 DATA DEFINITIONS Specify which data to read. Up to 3 data definitions can be defined (A, B and C). These data definitions can be allocated to one or more search definitions. Please make sure that the total length of the data does not exceed the maximum (depending upon the operating mode. See chapter 3.3.1.1). The total data length is determined by the data type, data length, constant data for all allocated data definitions.
Smartcard-Booster LEGIC 3.3.2 EXAMPLE CONFIGURATION In this chapter will be explained how to setup the configuration to accept LEGIC transponders with a Kaba Group Header segment. 3.3.2.1 OPERATING MODE Operating mode Dual-ID Vehicle-ID and driver-ID.
Smartcard-Booster LEGIC 3.4 TESTING THE CONFIGURATION The configuration can be tested on your read/write unit with the LEGIC cards that should be supported. This test can be performed before the configuration cards are created and without any Boosters. 3.4.1 SETUP TEST ENVIRONMENT First the configuration must be transmitted to the programmer. This is done by clicking 'Configuration', 'Test' and 'Setup configuration in read/write unit'.
Smartcard-Booster LEGIC 4 4.1 USAGE INFORMATION USING THE SMARTCARD-BOOSTER LEGIC Place the Smartcard-Booster behind the windscreen of your vehicle as described in chapter 2. The driver inserts his card and pushes the button on the Booster. A beep should indicate that the card was successfully read. The TRANSIT reader can identify your LEGIC card up to a distance of 10 meters now. After 5 seconds the Booster returns into standby mode.
Smartcard-Booster LEGIC 5 BUZZER INDICATIONS The Smartcard-Booster's built-in buzzer gives audible feedback upon various conditions. The table below describes the buzzer indications.
Smartcard-Booster LEGIC 6 BATTERY REPLACEMENT The Smartcard-Booster contains two replaceable non-rechargeable AAA batteries. The average lifetime of these batteries is approximately 5 years. When replacement becomes necessary follow the procedure below. 1. Open the battery compartment. 2. Remove both batteries. Follow local environment protection laws / regulations for disposal of used batteries. 3. Replace with two new batteries of the same type.
Smartcard-Booster LEGIC A TECHNICAL SPECIFICATIONS ITEM Dimensions SPECIFICATION 111 x 65 x 32 mm Weight 120 gram Protection IP32 (approx.
