STEAM PRESS LOC K UNL OCK MAX 400ml 300ml 200ml MIN MODEL:SP-80 OPERATING INSTRUCTIONS Please read this manual carefully before using and keep in a safe place for further use
CONTENTS Page 1． Features of the machine 3 2． Power Supply Index 3 3． Important Safeguards 4 4． Designation and application of various parts for electronic steam press 6 8 5． Operating The Steam Press 13 6． Pressing Suggestions 13 7． Pressing Application 14 8． Cleaning and maintenance 15 9． Trouble Shooting 16 2
1. Features of the machine 1. Saving time and effort: A pressing surface is seven times larger than most hand-held irons and reduces ironing . time. Approximatley 100LBS of steam per square inch which makes it easy to use for one hand operation; 2. Wide Application: Variable fabric temperature control from nylon to linen (20-200 degrees which prevents leaving a shine effect dry or steam press possible on all types of fabric; 3. Easy to handle: Possible to iron while either sitting down or standing up. 4.
3. Important Safeguards When using your steam press, the following safety precautions should be followed: 1. Use this press only for its intended use. 2. Before plugging in , be sure the electrical information on the label on the bottom of the press agrees with your power supply. 3. To protect against risk of electrical shock, do not immerse the press in water or other liquids. 4. The press should always be turned OFF before plugging into or unplugging from electrical outlet. 5.
4 1 LOCK 2 SILK WOO L OFF N LINE 6 7 MAX YE S 8 9 10 400m l 300m l 200m l MIN 11 12 14 13 5 5 N N YL O TT O N UNL OC K O C 3 LOC K UNLOCK STEAM NO
4.Designation and application of various parts for electronic steam press 1. Power Insert the plug into the power socket. Turn on the power at the wall socket and turn on the on/off switch on the side of the press. The off light on the control panel will turn on. 2. Power key: Make sure the ON/OFF switch to the ON position,it shows already connect the power,the(off) light on the operation display light up. 3. The steam control: Is set by default. For dry pressing simply press the No control.
8. The ironing board: Has a padded surface which holds the fabric during pressing. The board cover can be removed for cleaning or replacement. 9. Water tank: Holds the water for the steaming process. Pull the water tank half way out for water filling. 10.Base: It is used for storage of water for steaming. In case of no water, the water tank can be drawn out for water filling. 11. ON/OFF switch: Located under the ironing board, next to the power cord. 12.
5．Operation of electric ironing machine 1. Before inserting power cord A. It is required to check if the voltage indicated for the base of the machine shall be identical to the voltage of power supply you are using B. Place the electric ironing machine in a stable place 2.
3. Starting of electric ironing machine A. Hold down the handle of pressing board, pull up locking key, shake the handle lightly to make the locking pin retreat and pressing board separate with ironing plate. The hand shall not leave the handle and slight force shall be given to make it face upward automatically in slow way. B.
4. Temperature selection and control SILK WOO L OFF N LINE you wish to press. If you cannot determine the type of N N FABRIC INDICATION O TT YL O O N C Turn the temperature control dial to the kind of fabric fabric then begin at the lowest temperature setting SELECTION DIAL and increase until you achieve your desired result when the desired temperature has been reached the YE indicator light will stop flashing.
5. Steam Control A. The Sp80 will always start in default mode, the steam spraying function will be activated the steam light will turn on automatically on the display panel for dry pressing press the “No” steam control. As the pressing plate is lowered there will be a tick sound followed by the steam spray. Pause for 1-2 seconds each time the pressing plate is raised during steam pressing to maintain good pressing results.
6. Pressing Carefully spread the fabric area to be pressed on the pressing board. CAUTION: Please be careful not to touch the pressing plate. For dry pressing grasp the pressing plate handle and lower the pressing plate to press the fabric on the pressing board. For steam pressing in order to increase the steam spray to remove stubborn creases please adjust the fabric temperature..
6. Pressing Suggestions *You may find it desirable to place cloth between your fabric and pressing plate. *Buttons, zippers, etc. Most of today`s buttons, zippers and other notions require no special attention, however, some may be sensitive to heat. Care should be taken with items that may melt, place these items face down on the ironing board or cover with a press cloth before pressing.
7. Pressing Application Shirts and Blouses: A．Place the shoulder yoke on the ironing board first, face down and press. B．Place the sleeves on board with folds parallel to the long edge and press. C．Place the cuffs on the end of ironing board and press. D．Place the shirt into storage area and press the side front including the plackets and the opening/plactket. E．Pull the shirt section by section towards you and press. E．Place the yoke flat on the ironing board and press to remove the crease.
8．Cleaning and maintenance 1. To clean the pressing plate. Place the pressing pad in the centre of the ironing board, and place a clean towel over the pressing pad and board. Set the temperature to cotton and on to the steaming mode. Gently lower the pressing plate on to the pressing pad 3 to 4 times 2. Clean the pressing plate regularly with a damp cloth, do not use any abrasive cleaners. 3. The ironing board cover is easily removed for washing.
9. TROUBLE SHOOTING PROBLEM SOLUTION CAUSE 1. The machine cannot be opened by handle of pressing plate The locking switch is in lock position. 2. The steam press is hot but it does not remove creases Incorrect fabric temperature The temperature has not been set ● The plug of electric ironing machine has not been inserted into the socket ● 3.
Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
DO NOT THROW AWAY! RECYCLING We are committed to the protection of the environment. We strive tominimize the environment impact of our products by continuously improving product design and our manufac-turing methods. At end of life please dispose of this product in an environmentally responsible way. The crossed-out wheelie bin symbol featured above and on the product's data-plate means that this product falls under the scope of the E.U.
