User Guide

ManualsBrandsNEC ManualsOtherPlasmaSync 61XM2

PlasmaSync Plasma Monitor

NEC Solutions (America), Inc.

Model Information

For the operation of your plasma monitor,

refer to “Operation Manual”.

Summary of content (8 pages)

PAGE 1
PlasmaSync Plasma Monitor Model Information For the operation of your plasma monitor, refer to “Operation Manual”. NEC Solutions (America), Inc.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS (61XM2A/S) Read before operating equipment 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
PAGE 3
PRÉCAUTIONS IMPORTANTES DE SÉCURITÉ (61XM2A/S) A lire avant de faire fonctionner l’appareil 1. 2. 3. 4. 5. 6. 7. Lire ces instructions. Garder ces instructions. Respecter tous les avertissements. Suivre toutes les instructions. Ne pas utiliser cet appareil près de l’eau. Nettoyer seulement avec un chiffon sec. Ne pas boucher les ouvertures d’aération. Installer selon les instructions du fabricant 8.
PAGE 4
Important Information Warning NOTE: When you connect a computer to this monitor, use an RGB cable including the ferrite core on both ends of the cable. And regarding DVI and power cable, attach the supplied ferrite cores. If you do not do this, this monitor will not conform to mandatory FCC standards. Attaching the ferrite cores: Set the ferrite cores on both ends of the DVI cable (not supplied), and both ends of the power cable (supplied). Close the lid tightly until the clamps click.
PAGE 5
Recommandations importantes Avertissement Attention Ne pas utiliser dans une salle d’ordinateurs telle que définie dans la Norme pour la protection des ordinateurs électroniques/appareils de traitement des données ANSI/ NFPA75. Le 61XM2A/S est destiné à être utilisé uniquement avec les unités optionnelles suivantes. Toute utilisation avec d’autres unités optionnelles peut entraîner l’instabilité du placement.
PAGE 6
Specifications Color Reproduction Signals Synchronization Range Input Signals 1.8" (45) 57.9" (1470) 2.9" (74) 53.2" (1351) Horizontal : 15.5 to 110 kHz (automatic : step scan) Vertical : 50.0 to 120 Hz (automatic : step scan) RGB, NTSC (3.58/4.43), PAL (B,G,M,N), PAL60, SECAM, HD*1 , DVD*1 , DTV*1 34.7" (880) Aspect Ratio Resolution Pixel Pitch 53.2"(H)⳯29.9"(V) inches 1351(H)⳯760(V) mm diagonal 61" 16 : 9 1365(H)⳯768(V) pixels 0.039"(H)⳯0.039"(V) inches 0.99(H)⳯0.
PAGE 7
Table of Signals Supported Supported resolution • When the screen mode is NORMAL, each signal is converted to a 1024 dots⳯768 lines signal. (Except for *2, 3, 4) • When the screen mode is TRUE, the picture is displayed in the original resolution. • When the screen mode is FULL, each signal is converted to a 1365 dots⳯768 lines signal. (Except for *3) Computer input signals supported by this system Model 1280⳯1024 1024⳯768 1280⳯1024 Vertical frequency (Hz) 70.1 59.9 72.8 75.0 85.0 100.4 120.4 60.0 60.
PAGE 8
*1 *2 *3 *4 *5 Only when using a graphic accelerator board that is capable of displaying 852⳯480. This signal is converted to a 1024 dots ⳯ 640 lines signal. The picture is displayed in the original resolution. The aspect ratio is 5:4. This signal is converted to a 960 dots⳯768 lines signal. Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the RGB mode prepared for the input signals listed in the table above.